ページ1に含まれる内容の要旨
hi/lo
dup mon
channel/ volume
scan
UH039P
Operating Guide
To bring outstanding wireless communication products
to people's lives throughout the world.
hi/lo
dup mon
channel/ volume
scan
ページ2に含まれる内容の要旨
CONTROL & INDICATORS INCLUDED IN YOUR PACKAGE: UH039P Radio (2) Operating Guide Belt Clip (2) Charging Cradle with AC Adaptor NiMH Battery Pack (2) OPTIONAL ACCESSORIES VOX Earset VOX Headset Carry Case RX TX SCAN VOL VOX DUP HI hi/lo dup mon 13 15 14 channel/ volume scan RX TX 12 19 16 SCAN VOL VOX DUP 20 17 HI 21 18 22 1 Antenna 12 Channel Indicator 2 PTT (Push-To-Talk) Button 13 Receive Indicator 3 Channel/scan up Key 14 Transmit Indicator 4 Channel/scan down Key 15 Battery In
ページ3に含まれる内容の要旨
GETTING STARTED Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture. BATTERY INSTALLATION Your UH039P unit uses the included NiMH battery pack for power. The unit can be powered with optional 4 AAA ALKALINE batteries. To avoid damage to the unit do not mix old and new batteries. To install the batteries: 1. Make sure your radio is off. 2. Remove the battery compartment door by pressing the tab at the bottom of the compartment door, allowing the
ページ4に含まれる内容の要旨
dup mon channel/ volume scan charge 1 charge 2 Power Point Place the UH039P into the charge cradle. The charge light will come on to indicate the unit is charging. Before operating the UH039P, charge the battery pack for 16 hours. Do not charge alkaline or non rechargeable batteries. BELT CLIP To attach the belt clip: Slide the belt clip until it snaps into place. Belt Clip Locker To remove the belt clip: To remove the belt clip, press and hold belt clip locker, slide the belt clip at the same t
ページ5に含まれる内容の要旨
OPERATION POWER ON/OFF Press and hold to turn the radio on. A channel number will appear on the display. Press and hold to turn the radio off. VOLUME Press volume or to increase or decrease the volume level. VOL 'VOL' icon appears on the display while hi/lo volume is being adjusted. dup mon There are 8 volume levels. Level 0 (No channel/ volume scan Audio) to Level 7 (Maximum Volume). ADJUSTING THE KEY BEEPS Your radio emits a beep each time one of the keys (except for the PTT button) is pressed
ページ6に含まれる内容の要旨
SELECTING CHANNEL Press channel/scan or to select hi/lo dup mon the desired channel. channel/ volume scan TO TRANSMIT AND RECEIVE The UH039P uses the 40 UHF-CB Channels. For your reference a list of the available channels and corresponding frequencies is printed on page 10. 1. Before you transmit, listen for activity on the selected channel. TX 2. When the channel is clear, press PTT and hold the to transmit. PTT hi/lo 'TX' appears on the LCD. dup mon Switch channel/ volume scan Hold the radio w
ページ7に含まれる内容の要旨
TRANSMIT Hi/Lo SELECT dup Press and hold for 2 seconds when the unit is in Transmit Lo and it will switch to Transmit Hi. 'HI' icon will appear on HI display. dup Press and hold for 2 seconds again to return to Transmit Lo setting. 'HI' icon will disappear from display. The RF transmit power of the UH039P is selectable Transmit Power 0.3/0.7 W. AUTOMATIC SQUELCH FEATURE The UH039P is equipped with an Automatic Squelch System which shuts off weak transmissions and unwanted noise. MONITOR RX
ページ8に含まれる内容の要旨
TO OPERATE IN DUPLEX MODE (REPEATERS) The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08. UHF CB Repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions. Contact your retailer for a list of repeaters available in your area. Operation with the aid of a Repeater dup Press momentarily. The 'DUP' icon appears. DUP dup Press again to d
ページ9に含まれる内容の要旨
SCANNING The scan function scans all channels and stops at an active channel. When the signal stops, the UH039P waits 2 seconds (Reply Delay) before scanning resumes. To initiate scanning, SCAN 1. Assuming the unit is on CH01 when switched on. 2. Press and hold channel/scan or for 3 seconds and hi/lo scanning starts and Scan icon is dup mon displayed. channel/ volume scan PTT 3. Press or to cancel. If channel/scan or is pressed while the unit is paused on a channel, scanning is resumed. CTCSS (C
ページ10に含まれる内容の要旨
REPLY DELAY While scanning, the UH039P stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 2 seconds for the return of the signal, otherwise, the radio resumes scanning. VOX VOX is the automatic transmitting function by inputting voice PTT into the optional VOX headset mic without pressing the button. Press two times momentarily in Stand By mode to enter VOX Sensitivity mode. The current selected VOX setting will flash on the CTCSS channe
ページ11に含まれる内容の要旨
UHF CHANNELS & FREQUENCIES Simplex Mode Duplex Mode Simplex Mode Transmit / Receive Transmit Transmit / Receive CH No. CH No. Frequency (MHz) Frequency (MHz) Frequency (MHz) 1 476.425 477.175 CH31 21 476.925 2 476.450 477.200 CH32 22 476.950 3 476.475 477.225 CH33 23 476.975 4 476.500 477.250 CH34 24 477.000 5 476.525 477.275 CH35 25 477.025 6 476.550 477.300 CH36 26 477.050 7 476.575 477.325 CH37 27 477.075 8 476.600 477.350 CH38 28 477.100 9 476.625 29 477.125 10 476.650 30 477.150 11 476.675
ページ12に含まれる内容の要旨
WARRANTY UNIDEN UH039P UHF CB RADIO Limited One Year Warranty Please keep your sales docket as it provides evidence of warranty. Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498 Uniden New Zealand Limited Warranty only available in original country of purchase Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty, its UH039P UHF CB Transceiver Radio (hereinafter referred to as the Product) to be free from defects in materials and craftsman
