ページ1に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 1
UH060SX-2
Operating Guide
To bring outstanding wireless communication products
to people's lives throughout the world.
vol/ch
vol/ch
ページ2に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 2 CONTROL & INDICATORS INCLUDED IN YOUR PACKAGE: • UH060SX Radio (2) • Charging Cradle with AC Adaptor • Operating Guide • NiMH Battery Pack (2) • Belt Clip (2) • VOX Headset (2) OPTIONAL ACCESSORIES • VOX Earset • Carry Case 1 Antenna 14 Battery Level Meter 2 PTT (Push-To-Talk) Button 15 Receive Indicator 3 Monitor Button 16 Channel Indicator 4 Duplex/Call Key 17 Scan Indicator 5 Scan Key 18 VOX Indicator 6 Channel/Volume/Keylock Key 19 Keypad Lock
ページ3に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 3 GETTING STARTED Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture. BATTERY INSTALLATION Your UH060SX-2 unit uses the included NiMH battery pack for power. The unit can be powered with optional 4 AAA ALKALINE batteries. If you don't use the UH060SX-2 for long periods, Uniden recommend removing the batteries. The UH060SX-2 is designed to retain the previous user settings. This feature will contin
ページ4に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 4 INSTALLING THE CHARGE CRADLE • Plug the AC adaptor into the rear of the charge cradle and into the mains power. Place the UH060SX-2 into the charge cradle. The charge light will come on to indicate the unit is charging. Before operating the UH060SX-2, charge the battery pack for 16 hours. Do not charge alkaline or non rechargeable batteries. BELT CLIP To attach the belt clip: Slide the belt clip until it snaps into place. To remove the belt clip:
ページ5に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 5 OPERATION POWER ON/OFF Press and hold select/power key to turn the radio on. A channel number will appear on the display. Press and hold select/power key to turn the radio off. VOLUME Press volume/channel or key to increase or decrease the volume level. ‘VOL’ icon appears on the display while volume is being adjusted. There are 8 volume levels. Level 0 (No Audio) to Level 7 (Maximum Volume). ADJUSTING THE KEY BEEPS Your radio emits a beep each
ページ6に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 6 SELECTING A CHANNEL • Press ch/vol/keylock key momentarily to activate channel select mode. The displayed channel will flash. • Press volume/channel or key to select the desired channel. • Press ch/vol/keylock key momentarily to exit channel select mode. • If no button is pressed within 4 sec the UH060SX-2 will exit from the channel select mode. TO TRANSMIT AND RECEIVE The UH060SX-2 uses the 40 UHF-CB Channels. For your reference a list of t
ページ7に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 7 TRANSMIT Hi/Lo POWER SELECT • Press txp/ctcss key momentarily to select desired transmit level. • ‘HI’ icon will appear on the display for maximum transmit level. • ‘LO’ icon will appear on the display for minimum transmit level. • No transmit level appears for the middle transmit level • The RF transmit power of the UH060SX-2 is selectable between 0.1/0.5/1.5 W. AUTOMATIC SQUELCH FEATURE The UH060SX-2 is equipped with an Automatic Squelch System
ページ8に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 8 TO OPERATE IN DUPLEX MODE (REPEATERS) The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08. UHF CB Repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions. Contact your retailer for a list of repeaters available in your area. Operation with the aid of a Repeater Press dup/call key mom
ページ9に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 9 To initiate scanning, 1. Press scan key momentarily to begin scanning. The ‘SCAN’ icon is displayed. 2. Press select/power key or scan key to cancel. REPLY DELAY While scanning, the UH060SX-2 stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 2 seconds for the return of the signal, otherwise, the radio resumes scanning. CTCSS (Continuous Tone Coded Squelch System) CTCSS is a feature that
ページ10に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 10 The current selected VOX setting will flash on the display. Press volume/channel or key to adjust the VOX sensitivity. 1 is the highest sensitivity and 4 is the lowest sensitivity. VOX can be turned off by selecting ‘oF’ icon. The ‘VOX’ icon is shown on the display when VOX is selected to on and VOX Headset is plugged into VOX Headset Jack. The ‘TX’ icon blinks when the voice level is possible to transmit at the current selected VOX sensitiv
ページ11に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 11 UHF CHANNELS & FREQUENCIES Simplex Mode Duplex Mode Simplex Mode CH No. Transmit / Receive Transmit CH No. Transmit / Receive Frequency (MHz) Frequency (MHz) Frequency (MHz) 1 476.425 477.175 CH31 21 476.925 2 476.450 477.200 CH32 22 476.950 3 476.475 477.225 CH33 23 476.975 4 476.500 477.250 CH34 24 477.000 5 476.525 477.275 CH35 25 477.025 6 476.550 477.300 CH36 26 477.050 7 476.575 477.325 CH37 27 477.075 8 476.600 477.350 CH38 28 477.100 9 47
ページ12に含まれる内容の要旨
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 12 WARRANTY UNIDEN UH060SX-2 UHF CB RADIO Limited One Year Warranty Please keep your sales docket as it provides evidence of warranty. Warrantor: Uniden Australia Pty Limited ABN58 001 865 498 Uniden New Zealand Limited. Warranty only available in original country of purchase Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty, its UH060SX-2 UHF CB Transceiver Radio (hereinafter referred to as the Pro
