ページ1に含まれる内容の要旨
Cordless Cleaner
HANDY VAC II MODEL 4071D
INSTRUCTION MANUAL
SPEC I F I CAT1 0 N S
Capacity
Dimensions IL x W x H) Net weight
365 mm x 102 mm x 108 mm
600 mi 0 6 kg I1 3 Ibs)
! 114 318" x 4" x 4-1/4")
~~
* Manufacturer reserves the right to change specifications without notice
* Note Specifications may differ from country to country
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNINGTO reduce the risk of fire, electric shock, or injury: 1. Do not leave appliance when the battery cartridge is installed. Remove the battery cartridge from your appliance when not in use and before servicing. 2. Do not allow to be used as a toy. Close attention is necessary when used by or near
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS -This Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 3
ページ4に含まれる内容の要旨
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. A battery short can cause a large current flow, overheating, possible burns 5. and
ページ5に含まれる内容の要旨
Installing or removing battery cartridge I *Always switch off the tool before inser- Set date tion or removal of the battery cartridge. / To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully b
ページ6に含まれる内容の要旨
Switch action To start the tool, simply pull the trigger. Release the trigger to StOD. CAUTION : Before operation, always check to be sure that the filter and pre-filter are correctly in- stalled, or dirt and foreign matter will get into the motor and cause a failure. Cleaning (Suction) Nozzle Attach the nozzle to clean off tables, desks, etc. Nozzle slips on easily. furniture, Nozzle + Extension wand The extension wand fits in between the nozzle and the cleaner itself. This arrange
ページ7に含まれる内容の要旨
Crevice tool Fit on the crevice tool attachment for cleaning corners and crevice tool of a car or furniture. Sand and other heavy items can be sucked up easily. Crevice tool + Extension wand In tight quarters where the cleaner itself cannot squeeze in, or in high places hard to reach, the extension wand may be used. Tapping out filter When you notice less suction force during operation, stand the cleaner so that the intake hole is in the upright position and tap by hand the side of th
ページ8に含まれる内容の要旨
Dust disposal Raise the end of the cleaner so that the contents will not fall out. Then tap by hand the side of the capsule 4 or 5 times in order to detach materials from the pre- Tap or rap here (arrow-indicated position) filter and filter and facilitate emptying. Tip end of cleaner (with suction hole) down and unscrew capsule as indicated in arrow direction. Remove capsule carefully keeping it straight up and down so that the contents will not spill out. of the capsule and also Em
ページ9に含まれる内容の要旨
Turn the pre-filter and pull it off toward you, emptying out the fine dust inside. Then take out the filter and tap out any adhering dust. After emptying out the cleaner, re-assemble in the order shown in the figure. 1. Fit filter snugly on all the way. 2. Slip on pre-filter. 3. Screw on the capsule. Capsule Pre-f ilter Filter I I CAUTIONS: 0 Failure to re-assemble the filter and/or pre-filter so that they are back on all the way, or using a broken or ripped filter, can cause dust t
ページ10に含まれる内容の要旨
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. From time to time wipe off the outside (housing) of the cleaner using a cloth dampened in soapy water. Never use gasoline, thinner or the like or discolora- tion or cracks can take place. Rins out the filter in soapy water occa- sionally. Dry it out thoroughly before use. Never use an electric washer to clean the filter. I C
ページ11に含まれる内容の要旨
ACC ESSO R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons, The accessories or attachments should be used only in the proper and intended manner. 0 Extension wand 0 Nozzle assembly Part No. 412040-0 Part No. 122234-6 Nozzle assembly (for carpet) 0 Crevice tool Part No. 122291 -4 Part No. 41 1891 -8 0 Battery cartridge 7000 0 Fl
ページ12に含まれる内容の要旨
Jan.-08'87 EN CORDLESS CLEANER Model 4071D Note: The switch and other part configurations may differ from country to country. 12
ページ13に含まれる内容の要旨
9 1 Hanger 10 6 Tapping Screw 3x20 11 1 Filter 12 1 Pm Filter 13 1 Stop Ring CS 3 14 1 Valve 15 1 Capsule 16 1 Housing Set IWith Item 31 13
ページ14に含まれる内容の要旨
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other of disposal. I Ni-Cd I method To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that
