ページ1に含まれる内容の要旨
WorkingMan’s
Series
BASS SPEAKER
ENCLOSURES
USER GUIDE
includes:
WORKINGMAN’S 1X10T
WORKINGMAN’S 1X15T
WORKINGMAN’S 2X10T
WORKINGMAN’S 4X10T
WORKINGMAN’S TOWER
SWR SOUND CORP. • SUN VALLEY, CA • USA
ページ2に含まれる内容の要旨
SWR WORKINGMAN’S SERIES BASS SPEAKER ENCLOSURE USER GUIDE INTRODUCTION Congratulations on your purchase of an SWR WorkingMan’s Series bass speaker enclosure. By placing an SWR cabinet in your bass amplification system you have made a sound desicion that could very well be the best of your life! Just a little humor there, but true nonetheless. For over 15 years we here at SWR have been putting everything we know about bass into the SWR product line. We’ve earned a reputation for designing and
ページ3に含まれる内容の要旨
SWR WORKINGMAN’S SERIES BASS SPEAKER ENCLOSURE USER GUIDE TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Table Of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Input Panel Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 WorkingMan’s 1X10T . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
GENERAL INFORMATION Connection Only one amplifier at a time can be connected to your WorkingMan’s speaker enclosure. DO NOT plug two amplifiers into one speaker enclosure, as it will not work and may damage your system. Always complete your amplifier-to-speaker and speaker-to-speaker connections before powering up your system. Full Range Input and Output Jacks All WorkingMan’s Series speaker enclosures feature two, 1/4" full range input/output jacks wired in ® parallel (Note: The WorkingMan’s T
ページ5に含まれる内容の要旨
INPUT PANEL DIAGRAM All Models (except WorkingMan’s Tower) Tweeter Attenuator Switch 1/4" Input 1/4" Output INPUT PANEL DIAGRAM WorkingMan’s Tower Tweeter Attenuator Control 1/4" Input 1/4" Output Speakon Input Speakon Output 4
ページ6に含まれる内容の要旨
WORKINGMAN’S 1X10T Specifications Specifications Description: 1x10 and Tweeter Speaker Enclosure Power Handling: 100 watts RMS Impedance: 8 ohms Frequency Response & SPL: 96 dB SPL @ 1W1M (–3dB @ 70Hz and 18KHz) Speaker Complement: (1) Custom Designed, Stamped Steel Frame, 10" SWR Driver (1) Custom Designed Tweeter Porting: Front Slot Port Dimensions: 16.25"W x 14.5"H x 14"D Weight: 26 lbs. Connection and Operation The SWR WorkingMan’s 1X10T speaker enclosure can be connected to any musical in
ページ7に含まれる内容の要旨
WORKINGMAN’S 1X15T Specifications Description: 1x15 and Tweeter Speaker Enclosure Power Handling: 200 watts RMS Impedance: 8 ohms Frequency Response & SPL: 100 dB SPL @ 1W1M (–6dB @ 40 Hz and 18KHz) Speaker Complement: (1) Custom Designed, Cast Frame 15" SWR Driver (1) Custom Designed Tweeter Porting: Front Slot Port Dimensions: 23.25"W x 20.25"H x 18.5"D Weight: 45 lbs. Connection and Operation The SWR WorkingMan’s 1X15T speaker enclosure can be connected to any musical instrument amplifier
ページ8に含まれる内容の要旨
WORKINGMAN’S 2X10T Specifications Specifications Description: 2x10 and Tweeter Speaker Enclosure Power Handling: 200 watts RMS Impedance: 8 ohms Frequency Response & SPL: 98 dB SPL @ 1W1M (–3db @ 63 Hz and 18.5 KHz) Speaker Complement: (2) Custom Designed 10" SWR Drivers (1) Custom Designed Tweeter Porting: Front Slot Port Dimensions: 23"W x 17"H x 16.25"D Weight: 60 lbs. Connection and Operation The SWR WorkingMan’s 2X10T speaker enclosure can be connected to any musical instrument amplifier
ページ9に含まれる内容の要旨
WORKINGMAN’S 4X10T Specifications Specifications Description: 4x10 and Tweeter Speaker Enclosure Power Handling: 400 watts RMS Impedance: 8 ohms Frequency Response & SPL: 100 dB SPL @ 1W1M (–3dB @ 50 Hz and 18KHz) Speaker Complement: (2) Custom Designed 10" SWR Drivers (1) LCustom Designed Tweeter Porting: Front Slot Port Dimensions: 23"W x 25.25"H x 18.375"D Weight: 97 lbs. Connection and Operation Connection and Operation The SWR WorkingMan’s 4X10T speaker enclosure can be connected to any
ページ10に含まれる内容の要旨
WORKINGMAN’S TOWER Specifications Specifications Description: 8x10 and Tweeter Speaker Enclosure Power Handling: 800 watts RMS Impedance: 4 ohms Frequency Response & SPL: 93 dB @ 1W1M (–3dB 60 Hz & 13.5 kHz) Speaker Complement: (8) Custom Designed, Stamped Steel Frame, 10" SWR Drivers (1) Custom Designed Tweeter Porting: Front Slot Port Dimensions: 46.5" H x 22.375" W x 18.25 D" Weight: 110 lbs. 10" Speaker Specifications Individual Impedance: 8 Ohms (each) Power Rating: 100 Watts RMS (each) F
ページ11に含まれる内容の要旨
WORKINGMAN’S TOWER (continued) Tweeter Attenuator Control The large dial found on the input panel of the cabinet is the Tweeter Attenuator Control (see dia- gram, page 4). This control is used to adjust the level of high frequency signal present at the tweet- er. A normal setting for this control is straight up or “twelve o’clock.” Turning the dial fully counter- clockwise removes the tweeter from the circuit. As you turn the dial clockwise from this position, the high frequency content is inc
ページ12に含まれる内容の要旨
IMPEDANCE: A GENERAL OVERVIEW The following terms will be helpful in understanding the information in this section: Impedance: The resistance of a device to the flow of alternating current. Often used to rate the resistance of a speaker's voice coil. Ohm: A unit of electrical resistance equal to that of a conductor in which a current of one ampere is produced by a potential of one volt across its terminals. Parallel Operation: The connection of two or more power sources of the same output volt
ページ13に含まれる内容の要旨
IMPEDANCE (continued) one 8 ohm enclosure, you know you can add one more 8 ohm speaker safely (8 divided by 2 = 4). Although much less common, you could also add one, or even two, 16 ohm cabinets: two 16 ohm cabinets in parallel have the same total impedance as one 8 ohm speaker. To get the most efficiency out of your system with the fewest cabinets, your best choice would be to connect two 8 ohm enclosures. Since you would be driving two cabinets of equal impedance, each will receive half the p
ページ14に含まれる内容の要旨
than one cabinet, check all cable connections in the chain. If you then suspect that the problem may be a bad cable, you can use a 9 volt battery as a cable-tester. To do so, plug one end of the questionable cable into your speaker cabinet, and then touch the phone plug on the other end to the two terminals (+ and –) of the battery, contacting the tip and sleeve. When you connect the bat- tery to the phone plug, a good cable will will pass the voltage to the speakers, which will be indicat- ed
ページ15に含まれる内容の要旨
SWR LIMITED WARRANTY SWR LIMITED WARRANTY All SWR WorkingMan’s Series Speaker Enclosures are warrantied to the original consumer purchaser for a period of One (1) Year (with the exception of the WorkingMan’s Tower which is warrantied for Two (2) Years) from the date of purchase in the USA from an Authorized SWR Dealer. The warranty is VOID if the unit has been damaged due to accident, improper handling, installation or operation, modification, shipping damage, abuse or misuse, unauthorized repa
ページ16に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER OR BACK. CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. PLEASE REFER TO A QUALIFIED SERVICE TECHNICIAN. NO USER-SERVICEABLE PARTS INSIDE. PLEASE REFER TO A QUALIFIED SERVICE TECHNICIAN. A. Read Instructions: A. Read Instructions: All safety and operation instructions should be read before the product is operated. B. Retain Instructions
ページ17に含まれる内容の要旨
More WorkingMan’s Series Gear WORKINGMAN’S 4004 Pro features at an affordable price! 400 watts of power housed in a durable road case with an extra rack space for your effects. Shape your tone with a 5-band EQ sec- tion, Aural Enhancer, and a variable limiter. Other fea- tures include: Tuner out for silent on-stage tuning, XLR Out to run your signal directly to the PA or recording console, and an effects loop. Lightweight and easy to transport. WORKINGMAN’S 2004 200 watt head designed for the w
ページ18に含まれる内容の要旨
©2001 SWR Sound Corp. All rights reserved. PART NO. 320033 REV. 05/01 Learn more about SWR products and artists by point- ing your browser to: swrsound.com SWR SOUND CORPORATION 9130 Glenoaks Blvd. • Sun Valley, CA 91352 USA (818) 253-4797• Fax: (818) 253-4799
