ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
DSR-3706PA
Digital Video Recorder
with Multiplexer Function
About this manual
Before installing and using this unit, please read this manual carefully.
Be sure to keep it handy for later reference.
ページ2に含まれる内容の要旨
English Table of Contents Searching for recorded video. . . . . . . . . . . . . . . . . . . . . .21 Foreword A Alarm search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 B Alarm thumbnail search . . . . . . . . . . . . . . . . . . . . .22 These must be followed for safety reasons . . . . . . . . 3 b Viewing pre-alarm video . . . . . . . . . . . . . . . . . . . .22 Follow the points outlined below f
ページ3に含まれる内容の要旨
Table of Contents B Recording area menu description. . . . . . . . . . . . . 43 E Network settings . . . . . . . . . . . . . . . . . . . . . . . . . . .69 b Verifying the capacity of the recording areas. . . . 43 E-1 Network password modification . . . . . . . . . . . . .69 B-1 Changing the normal recording area F RS-485 settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 and the alarm recording area . . . . . . . . . . . . . . . 44 Screen settings . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
English Safety precautions These must be followed for safety reasons Warning b Do not use if the unit emits smoke, or b Do not use during thunder/thunder storms. while abnormal sounds and smells Do not use during thunder/thunder storms. are detected. Never make contact with the connection Remove the power cable. This may cause electrocution. cable from the Using in an abnormal condition may cause outlet. Contact prohibited electrocution and fires. Immediately remove the power cable from t
ページ5に含まれる内容の要旨
Safety precautions Caution b Delivery and portability b Do not expose to extreme temperatures or temperature variations. Never move this unit while the power is turned on. Do not place in areas where the unit will Remove the power be exposed to extreme temperatures (±10 Remove the power cable from the outlet, cable from the outlet. degrees Centigrade per hour) or moisture confirm that the connection cable has Prohibited changes. been removed, and store in original packaging before
ページ6に含まれる内容の要旨
English Safety precautions Follow the points outlined below for proper use b Hard disk This unit is loaded with a hard disk drive. Stored data on this unit may be damaged/lost through hard-disk breakdowns caused by shock/vibration. Follow the items outlined below when placing, transporting, and operating this unit. Warning Caution G This unit is designed to be positioned horizontally. G Inspecting for abnormalities in the hard disk drive and Do not position vertically. the cooling fan G Do not
ページ7に含まれる内容の要旨
Safety precautions bBack up battery bMaintaining this unit A lithium battery (fixed) is built into this unit. Supplying Turn the power off and remove the power cable from power for more than 48 hours after setting the date and the outlet. time will allow the internal power source to sustain the Wipe away dust using a soft cloth. set time for 30 days. When the stains are hard to remove... The battery is expected to last for approximately 5 years if the unit is used regularly. Soak the clot
ページ8に含まれる内容の要旨
English Main Features Accessories b This digital video recorder (DVR) can record video Check that you have all the parts shown below. from surveillance cameras to its internal hard disk, Quick Guide and it can display the video on a screen split into six Instruction Manual (Digital Video Recorder) or four fields, both during recording, and playback. Manual for Remote Operation using a Network Connection b Complete range of recording and playback functions Mounting screws for hard disk
ページ9に含まれる内容の要旨
Names and functions of parts (front panel) DSR-3706PA 1 2 345 6 7 8 9FGHI 1 Power indicator (POWER) 8 USB terminal (USB) On: The power cord at the rear panel of the DVR is This terminal connects to an optional CD-R/RW drive. inserted in the outlet. When the front panel and the rear panel terminals are Off: The power cord on the rear panel of the DVR is not connected simultaneously, the front panel is given priority. inserted in the outlet. 9 Camera selection buttons and indicators Fast blinking
ページ10に含まれる内容の要旨
English Names and functions of parts (front panel) J KL M X W W 12 Open Pull out Front N O P 2 Q Insert 3Fold down 1Lift and (lock) push RS T U V J Menu button and indicator (MENU) S Timer-controlled recording button and indicator (TIMER) On: The menu is displayed. On: Timer-controlled recording or standby. Off: The EXIT/OSD button is pressed. Off: When pressed again (cancel) K Exit/Operation screen display button and indicator (EXIT/OSD) T Alarm buttons ( ALARM ) On: Displaying the channel a
ページ11に含まれる内容の要旨
CLOCK OUT CLOCK IN NON REC OUT EXIT TIMER IN SERIES OUT SERIES IN ALARM FULL FULL WARNING OUT ALARM RESET ALARM OUT Names and functions of parts (rear panel) Basic connections 3 Video input terminal (Video IN) 1 Clear button (ALL RESET) Press to reset the clocks connected to the digital video Connect SANYO protocol cameras (dome or zoom) or generic recorder to their initial values. cameras to these terminals. (P70) ALL Camera (sold separately) RESET 2 Video output terminal (Video OUT) Outputs
ページ12に含まれる内容の要旨
English CLOCK OUT CLOCK IN NON REC OUT EXIT TIMER IN SERIES OUT SERIES IN ALARM FULL FULL WARNING OUT ALARM RESET ALARM OUT Names and functions of parts (rear panel) Alarm and RS-485 connections 1 Alarm input terminals (ALARM IN) 2 Sensor alarm output terminals Connecting a switch or security sensor etc. to the terminal of the (SENSOR ALARM OUT) DVR allows the detection of the intrusion of outsiders when doors This terminal is used to output the signals listed below etc. are opened and close
ページ13に含まれる内容の要旨
CLOCK OUT CLOCK IN CLOCK OUT CLOCK IN SERIES IN FULL ALARM RESET ALARM OUT NON REC OUT EXIT TIMER IN SERIES OUT SERIES IN ALARM FULL FULL WARNING OUT ALARM RESET ALARM OUT Names and functions of parts (rear panel) Control terminals (CONTROL) This DVR can be remotely controlled when a remote-control circuit (R1, R2, C) similar to that shown below is connected to the remote-control terminals. Use a resistance of 1/10 ohms or more and with a D ranking (Precision within ±0.5%). The remote contr
ページ14に含まれる内容の要旨
English Preparing for use Turn on the power of the DVR Language, clock settings Connect the supplied power cable. Press the MENU button and turn the S-dial 1 1 clockwise 3 times. The power indicator turns on, and the monitor displays the "PLEASE SET THE CLOCK !" message. "ENGLISH" starts blinking. The DVR performs playbacks or searches based on the MENU recording date and time. Select the LANGUAGE/ 1.INITIAL SET -> CLOCK SET using the INITIAL
ページ15に含まれる内容の要旨
Preparing for use Operation display The operation display shows information necessary for Changing the position of the operation display operation, such as the date, time and video quality. The Whenever the EXIT/OSD button is pressed, the position of operation display can be hidden. the operation display changes. 12 34567 8 EXIT/OSD 01-01-06 00:00:00 REC REPEAT EN A ALARM 0000 (Hidden) 0 02 02 02 F9 1 Date display 7 Recording type 01-01-06 (day, month, year): Do not forget to set the
ページ16に含まれる内容の要旨
English Viewing live video using various multi screens Switching to another full-screen video Enlarging an image (Plus screen display) Press the camera selection button (example 2, 6) of the desired camera. Press the PLUS button. 1 The video from Camera 2, then the video from Camera 6 are One camera image is displayed enlarged. displayed. Plus screen PLUS 02 02 06 01 03 2 6 04 04 05 05 06 06 Press the camera selection button (example 6). 2 The corresponding image is enlarged. ☞ Refer to P20 f
ページ17に含まれる内容の要旨
Viewing live video using various multi screens Automatic screen scrolling Viewing on the monitor connected to the MON2 terminal A Automatic full-screen scrolling Connect a monitor to the MON2 terminal on the rear panel. Press the SEQUENCE button. The display is full-screen only. (P10) The live surveillance video scrolls through the cameras in the While the main monitor is used in split-screen mode, the order of the camera numbers. monitor 2 connected to the MON2 terminal can be used to To s
ページ18に含まれる内容の要旨
English Recording video to the hard disk The internal hard disk is automatically formatted with Normal recording recording area, normal recording, recording conditions, (normal recording area) etc. Before starting recording, verify the recordable duration for normal recording (List of recording rate and Video from all cameras connected to the video input terminals recording times: P83). The formatting can be modified of the DVR can be recorded with one touch of a button. using "Recording
ページ19に含まれる内容の要旨
(Normal recording area) Viewing recorded video This DVR can play video that has already been recorded or Full-screen viewing currently being recorded in the normal recording area (by normal or timer-controlled recording). Press the PLAY/STOP button. 1 Normal recording area The " " symbol appears in the operation display area and the video starts playing. 26-10-06 09:30:00 REC REPEAT EN A ARCHIV 0001 PLAY/STOP (Hard disk recording areas) 02 Playback When playback ends, the DVR pauses auto
ページ20に含まれる内容の要旨
English Viewing recorded video Changing the playback speed Viewing still images The corresponding symbol ( , ...) appears in the Press the STILL button during playback. operation display area for each of these operations. The image is paused. The " " symbol appears in the Audio will not be played when changing the playback speed. operation display area. Press the STILL button once again, to return to normal A Fast-forward/Slow playback playback. 26-10-06 09:30:00 REC REPEAT EN A ALARM 0000 S
