ページ1に含まれる内容の要旨
SIZE:139X216mm
ページ2に含まれる内容の要旨
1. BUTTONS LOCATION AND FUNCTIONING 1 8 11 3 PANEL MONO/ AUTOMATICALLY RELEASE STEREO STORE / PRESET CD EJECT BUTTON BUTTON SCAN BUTTON BUTTON VOLUME AUDIO MUTE PRESET MEMORY BUTTONS (M1~M6) SCAN KNOB BUTTON BUTTON BUTTON 10 4 2 7 9 12 6 15 17 LOCAL/ REMOTE PRESET POWER DISTANT CONTROL EQUALIZER BUTTON BUTTON RECEIVER BUTTON BAND/ DISPLAY SOURCE TUNING UP / DOWN LOUDNESS BUTTON BUTTON / TRACK UP / DOWN BUTTON SUB-WOOFER BUTTONS 5 13 16 14 E - 1
ページ3に含まれる内容の要旨
2. HANDLING COMPACT DISCS MOISTURE CONDENSATION On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. NOTES ON CDs NOTES ON DISCS If you use the discs explained below, the sticky 1. A dirty or defective disc may cause sound residue can cause the CD to stop spinning and dropouts while playing. To enjoy optim
ページ4に含まれる内容の要旨
3. INSTALLATION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the pa
ページ5に含まれる内容の要旨
Removing the unit a a. Frame b. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove down wards b and attach it.) c. Insert the levers supplied with the unit c into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard. Trim Plate Installation: Push the trim plate against the chassis until it is fitt
ページ6に含まれる内容の要旨
4. DETACHABLE CONTROL PANEL (D.C.P.) Removing The Detachable Control Panel (D.C.P.). 1. Turn the power off 2. Press the D.C.P. release button 3. Remove the D.C.P. PANEL RELEASE BUTTON Attaching the DCP 1. Attach the panel at the right side first, with point B on the main unit touching point A on the 2 D.C.P . (As shown on the digram). A 2. Then press the left side of D.C.P . onto the main unit until a “click” sound is heard. B CAUTION DO NOT insert the D.C.P from the left side. Doing so m
ページ7に含まれる内容の要旨
SUB-WOOFER 5. WIRING DIAGRAM (20 PIN HARNESS PLUG) ANTENNA J ACK ANTENNAPEXT ENDERP CABLE FUSE 20-PIN AUDIO/POWER HARNESS (See Figure 1) WHITE RCA-TO-RCA CABLES (not supplied) SUB WOOFER YELLOW BLUE AUX IN WHITE RED RCA-TO-RCA CABLES (not supplied) WHITE REAR LINE OUT GREY RED AMP WHITE FRONT LINE OUT BLACK RED Power Antenna Connect to power antenna or amplifier,If not used,Tape bare end of wire. BLUE Ground Connect to ground terminal or chassis BLACK Clean unpainted metal p
ページ8に含まれる内容の要旨
6. BASIC OPERATIONS 1) PANEL RELEASE BUTTON (REL) Press this button to remove the control panel. 12) POWER ON/OFF BUTTON Press this button to turn on or off the power. 5) DISPLAY BUTTON (DISP) Press this button briefly, the LCD will display the clock for about 2 seconds, then return to previous display mode. Clock Adjustment Under clock display mode, press DISP button until the LCD flashes, press Tuning Up Button to adjust hour and Tuning Down Button to adjust minute. 16) SOURCE BUTTON (S
ページ9に含まれる内容の要旨
7. AUDIO OPERATIONS 10) VOLUME KNOB Turn this knob to adjust desired volume level. 4) AUDIO BUTTON Press this button to select desired audio function. ORDER OF FUNCTION: VOLUME(VOL) -> BASS(BAS) -> TREBLE(TRE) ->BALANCE(BAL) ->FADER(FAD) While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds, otherwise the unit will return to volume adjustment mode. 2) MUTE BUTTON (MUTE) Press this button to mute the sound. Press it again to resume listeni
ページ10に含まれる内容の要旨
8. RADIO OPERATIONS 11) AUTO MEMORY STORE/PRESET SCAN BUTTON (AS/PS) 1.PRESET SCAN: Press AS/PS button briefly to enter Preset Scan mode, it will scan all the preset stations in the memories, you can hear that it will stay on each station for about 5 seconds. 2.AUTO MEMORY STORE: Press AS/PS button for couple of seconds to enter Auto Store mode, this feature will automatically scan the current band and enter up to 6 strongest stations into the 6 preset memories. To stop Auto Store & Scan, p
ページ11に含まれる内容の要旨
9.CD OPERATIONS M1) PAUSE BUTTON (PAUSE) Press this button to pause CD play, press again to release pause. M2) SCAN BUTTON (SCAN) Press this button, the first 10 seconds of each track will be played sequentially until this button is pressed again, then normal play will resume at the current track. M3) REPEAT BUTTON (REPEAT) Press this button, the current track will be played repeatedly until this button is pressed again. M4) SHUFFLE BUTTON (SHUFFLE) Press this button to play all tracks on CD i
ページ12に含まれる内容の要旨
10.REMOTE CONTROL 8 1 9 2 3 10 4 11 5 6 12 13 7 14 OPERATIONS: Key Radio Mode CD Player Mode ( ) Power On/Off Power On/Off 1. Power Adjust Vol,Bas, Adjust Vol,Bas, 2. Volume Up/Down Tre,Fad,Bal Tre,Fad,Bal Display Clock Display Clock 3. DISP 4.Stereo/Mono No Function Stereo/FM Mono 5. Tuning Up/Down Tuning/Seek Up/Down Track Up/Down Local/Distant No Function 6. LOC 7. Scan Station Scan No Function Mute 8. Mute Mute Select Vol, Bas, Select Vol, Bas, 9. Audio Tre, Fad, Bal Tre, Fad, Bal Sub-wo
ページ13に含まれる内容の要旨
11.SPECIFICATIONS CD PLAYER System Compact disc audio system Compact disc Usable disc 44.1KHz Sampling frequency 1bit No of quantization bits 5-20,000Hz Frequency Number of channels 2 stereo 70dB S/N Ratio RADIO SECTION FM Frequency Range 87.5-107.9MHz 10.7 MHz Intermediate Frequency Better than 15dB at S/N 30 dB Usable Sensitivity Stereo Separation 25 dB at 1KHz 50 dB S/N Ratio AM/MW Frequency Range 530-1710KHz 450KHz Intermediate Frequency Usable Sensitivity Better than 45dB 40 dB S/N Rati
ページ14に含まれる内容の要旨
12.TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution If the power supply is properly connected No power The car ignition is not on. to the car accessory terminal, switch the ignition key to “ACC” The fuse is blown. Replace the fuse. Disc cannot be loaded Remove the disc in the player, then put a Presence of CD disc inside or ejected new one.
ページ15に含まれる内容の要旨
