ページ1に含まれる内容の要旨
f I
~ I
;
~
~
i
£j:i'-; , ,,"
j
~
SO-O216A-xxx SERIES 118127X
DODGEDURANGO
OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM
~
OPTIONAL ACCESSORIES MA y BE ADED:
ESCORT PASSPORT 4600 RADAR DETECTOR
1
MINI- TRIP COMPUTER FROM O.E.M. OVERHEAD
2
These instructions are intended for use only by experienced professionals in the automotive
customizing business. Special tools and equipment, as well as specialized handling and care
of product during installation, may be required. Before beginning this
ページ2に含まれる内容の要旨
[ MA TERIALS PROVIDED FOR INST ALLA TION ~ ~ . . i { I . lrEMi~,pe~cription ,gTY ..;!~",;;c..c;, .. ,~;.:~~':~,;; ~! " ,,-';;;c.:,; t SCREW, # 6 X Y2 PPH 13 1 1 ~. SCREW,#8X* HWH 6 2 SCREW, # 8 X 11/4 PWH 2 3 FRONT MOUNTING BRACKET 1 2 4 COMPUTER MOUNTING BRACKET I 5 REAR MOUNTING BRACKET I 6 RADAR DETECTOR HOUSING I 3 7 BLOCK OFF I 8 CONSOLE I 9 " FRONT LIGHT I 10 FRONT LIGHT TRIM I 11 5 4 8 ~ D 9 c ~ ;. s I!: l i. i ~ 7 10 11 Apr. 13, 1998 INSTALLATION INSTRUCTION # 44-0021A Printed in the U.S
ページ3に含まれる内容の要旨
.. ~ ({ I. PREPARATION OF VEHICLE INTERIOR ~ .""4.' $ "' ~ * ;t ~ ,; ,J: if. ,;;::.:!~emoveand discard fr.on(dOln~ light and , proceed to step 7. 2. Remove front mounting screw from overhead console and slide forward to release tabs at rear of console. See figure 1. I 0 / / FIGURE 1 . 3. Disconnect wiring harness from console. See fig. 2 . 4. Individually cut and remove the green, white, and black wires that control the map lights , from the connector on the mini-trip computer. - ~ ~ 5. Remove a
ページ4に含まれる内容の要旨
7" T ~" -~~:i" ~tC ~ ~5rf:; ."," ~",,~' ,~~ 8. Carefully trim headliner and drill (2) two Y2" holes in return air grille to allow for screws to pass through when mounting bracket. See fig. 4. FIGURE 4 T 1 t~ 9. Install rear mounting bracket (item 6 pg 2) and '--"- secure using (4) four # 8 x 3,{" screws (item 2 pg 2). Make sure that holes in bracket align with dimples in roof brace. See figure 5. FIGURE 5 II. PREPARATION OF CONSOLE FOR INSTALLATION .f ~ ~ f ii ;: L W ~ ~ 10. Install the video sy
ページ5に含まれる内容の要旨
i t ';; ,. i{ :'i ~; bI;: ;, ". :! 11. Install fro~,tjig4t(item 10 pg 2) and secure ,-,,"= , "'" i -using (3) three::~~6;;kV2" screws {item 1 pg'2).. ;} ~ Install front light trim (item II pg 2) around light. See figure 7. \ I . . 12. There are 3 options available for the front of the console. For no accessory see step A. For radar detector housing see step B. For O.E.M. mini- trip computer see step C. A. Install block off (item 8 pg 2) and secure using (4) four # 6 x ,Y2" screws. See fig. 8. .,
ページ6に含まれる内容の要旨
if ~~ ~ .; ~ 'I' ii " ~ ii .if 9 c. Install O.E.M. mini-trip computer bezel from the backside of opening in console. Install computer mounting bracket (item 5 pg 2) and secure using (2) two # 6 x Y2" screws (item 1 pg 2). See figure 10. fj ij ~ . .n FIGURE 10 Install O.E.M. mini-trip computer and secure using (4) four #6 x 1f2" screws (item I pg 2). See figure 11. Do not overtighten screws. FIGURE 11 6
ページ7に含まれる内容の要旨
f ~ :;: ... III. INST ALLA TION OF CONSOLE ~ '. " " " . ~ NOTE: Additional a"ssistance in mounting the overhead console in vehicle is ~ advised to prevent damage to console or components. rf c ~- J ;t 13. Install and route all accessory wiring, video and audio cables, and any other added ~ component requirements to their respective r. t places in the vehicle. Refer to component f installation instructions for wiring diagrams. The suggested routing of the video system cable is as follows: Above t
ページ8に含まれる内容の要旨
"' .r I. ~ . #. . ~ j ~ ~ 'f :f ~ o :.: ~, 17. Using an awl or similar tool, align the front mounting holes in console with holes in bracket. Secure using (2) two # 8 x 1 ~" screws (item 3 pg 2). See figure 14. Caution: Do not overtighten screws. Figure 14 . } . . , il ); 8
