ページ1に含まれる内容の要旨
19 inch HN Series
TFT LCD Monitor
USER’S MANUAL
ページ2に含まれる内容の要旨
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radia
ページ3に含まれる内容の要旨
User’s Manual Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonom
ページ4に含まれる内容の要旨
User’s Manual Recycling Information We, the HannStar Display Corp. care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly
ページ5に含まれる内容の要旨
User’s Manual TABLE OF CONTENTS SAFETY NOTICE ........................................................................................... 6 PRECAUTIONS......................................................................................... 6 SPECIAL NOTES ON LCD MONITORS ................................................... 7 BEFORE YOU OPERATE THE MONITOR.................................................... 8 FEATURES ......................................................................
ページ6に含まれる内容の要旨
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interferenc
ページ7に含まれる内容の要旨
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of
ページ8に含まれる内容の要旨
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor (Reference only, the real feature is depended on selected model) Screen Base Cables and User manual Power Cord VGA Cable Au
ページ9に含まれる内容の要旨
User’s Manual INSTALLATION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged in
ページ10に含まれる内容の要旨
User’s Manual To set up the device, you need to assemble the monitor stand. Join the stand base to the stand post. You should be able to hear it slot in. Insert the screw enclosed, tightening it with a coin or a screwdriver, so that the stand base is attached securely to the stand post. To set up the device, you must fi t the monitor base together. You can adjust the height of the base. When the base of the monitor is extended, you can tilt the monitor 90° (Pivot function). POWER
ページ11に含まれる内容の要旨
User’s Manual CONTROLS AND CONNECTORS CABLE CONNECTIONS: Turn off your computer before performing the procedure below. 1. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the 24-pin DVI cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI port. 3. Connect the audio cable between the monitor's audio input and the PC's audio outpu
ページ12に含まれる内容の要旨
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from 0 ° to 20 °. monitor’s angle Figure.3. NOTES: • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. • Be car
ページ13に含まれる内容の要旨
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor position. The power indicator will light up. F
ページ14に含まれる内容の要旨
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange — Off mode. • MENU / ENTER: 1. Active OSD menu or function adjust confirm or 2. Exit OSD menu when in volume OSD status. • Volume < >: 1. Activates the volume control when the OSD is OFF. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. • Auto Adjust button: When
ページ15に含まれる内容の要旨
User’s Manual HOW TO ADJUST A SETTING OSD Diagram OSD Description Brightness/Contrast adjustment: Brightness: Adjusts brightness by using the buttons < or > (② and ⑤ in fig. 4). Contrast: Adjusts screen contrast by using the buttons < or > (② and ⑤ in fig. 4). Image Control: Auto Adjustment: Automatically selects the optimal settings for image parameters (image position, phase, etc.) by using the button MENU (① in fig. 4). H. Position: Controls the picture’s horizontal position
ページ16に含まれる内容の要旨
User’s Manual OSD Diagram OSD Description OSD Control: H. OSD Position: Controls the OSD menu’s horizontal position. V. OSD Position: Controls the OSD menu’s vertical position. OSD Timeout: Determines how long (in seconds) the OSD menu waits before closing automatically after no action has been performed. Other: English. French. German. Italian. Spanish. Japanese. Portuguese. Nederlands. Korea. Simplify Chinese. Traditional Chinese. Input: Controls the selection of the input
ページ17に含まれる内容の要旨
User’s Manual electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The
ページ18に含まれる内容の要旨
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL DEFECTIVE PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position Power LED is not on *Power Cord should be connected *Check if the PC system is Plug & Play compatible No Plug & Play *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave *Move electrical devices
ページ19に含まれる内容の要旨
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. FACTORY PRESET TIMING TABLE: HORIZONTAL VERTICAL VIDEO MODE RESOLUTION FREQUENCY (kHz) FREQUENCY (Hz
ページ20に含まれる内容の要旨
User’s Manual APPENDIX SPECIFICATIONS Driving system TFT Color LCD Size 48.2cm(19.0") Pixel pitch 0.294mm(H) x 0.294mm(V) 2 LCD Panel Brightness 270cd/m (Typical) Contrast 700:1 (Typical) Viewable angle 150 ° (H) 135 ° (V) Response time 8 ms R,G,B Analog Interface Video Digital (Dual-Input Model) H/V TTL Input H-Frequency 31KHz – 80KHz V-Frequency 55 – 75Hz Display Colors 16.2M Colors Dot Clock 135MHz Max. Resolution 1280 x 1024 @75Hz TM VESA DDC2B Plug & Pla
