ページ1に含まれる内容の要旨
9101443100
»
302@#
Double Auto Reverse Cassette Deck
OWNER’S MANUAL
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
Ü
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
ÿ
that may be of sufficient magnitude to constitute a risk of electric sh
ページ2に含まれる内容の要旨
Important Safety Precautions For U.S.A IMPORTANT (for U.K. Customers) TO THE USER This equipment has been tested and found to DO NOT cut off the mains plug from this equipment. comply with the limits for a Class A digital If the plug fitted is not suitable for the power points in your home or device, pursuant to Part 15 of the FCC Rules. the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Th
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS CAUTION: "Note to CATV system installer: …Read all of these Instructions. This reminder is provided to call the CATV system installer’s attention to …Save these Instructions for later use. Section 820-40 of the NEC which provides guidelines for proper grounding …Follow all Warnings and Instructions marked on the audio and, in particular, specifies that the cable ground shall be connected to t
ページ4に含まれる内容の要旨
Before Getting Started The TASCAM 302MKII is a double auto reverse Rack Mounting cassette deck primarily designed for continuous The 302MKII can be installed in a standard 19" rack, playback of background music or tape dubbing needs. using the provided 4 pairs of screws (M5 x 12) and 4 A maximum of ten 302MKIIs can be hooked up to washers, as shown. form a sequential play loop or to synchronize them, with one serving as the master/source machine and the others serv
ページ5に含まれる内容の要旨
General Guide to the Controls and Connectors TASCAM 302MKII 5
ページ6に含まれる内容の要旨
General Guide to the Controls and Connectors Front Panel 1 POWER switch : Turns the unit on and off. deck 2, or MIX for monitoring a mix of two tape signals. During Record Ready or Record modes, NOTE you can monitor input signals, as selected with this The equipment draws nominal nonoperating power switch. from the AC outlet with its POWER switch in the OFF position. B PHONES control : Adjusts the listening level of the headphones plugged into the PHONES jack.
ページ7に含まれる内容の要旨
General Guide to the Controls and Connectors MDOLBY NR switch : Selects the Dolby B or C Q INPUT/OUTPUT switch : Set to SEPARATE for Noise Reduction system or defeats them. When deck 1 and deck 2 to operate independently from listening to a recording, set this switch to the setting each other. With SEPARATE engaged, the inputs used for the original recording. and outputs on the rear panel are independent for each deck. Only in DUAL REC mode, the inputs to deck 1 have access to deck 2 as well. D
ページ8に含まれる内容の要旨
General Guide to the Controls and Connectors Rear Panel TDECK 2, INPUT and OUTPUT jacks : These V CASCADE OUTPUT jacks : Used for dubbing jacks are independent from deck 1 all the time. from a deck onto, or recording from an external single source on multiple decks, as shown in the NOTE diagram on page 13. These jacks are only operational when the INPUT/ OUTPUT switch is set to the SEPARATE position. WEXT CONTROL jack : Used to connect a multiple-unit system, as shown in the diagram on page 12.
ページ9に含まれる内容の要旨
Using a Single Unit Recording on Either Deck, or Both at the Same Time Unless you use multiple 302MkII units connected in If you are using only one of the two decks, put it series, set the OFF/SLV/MSTR switch to the left OFF into Record Ready mode by holding down position all the time. RECORD and pressing PAUSE. 1. Check to see that the source is connected to the DECK 1 INPUT connectors if you intend to record on deck 1 only or on deck 1 and deck 2 simul- taneously. Use the DECK 2 INPUT connect
ページ10に含まれる内容の要旨
Using a Single Unit Continuous Recording on Both Decks When the tape on deck 1 records up to the end of the “ The INPUT/OUTPUT switch must be set to reverse side, the tape on deck 2 will start recording, SEPARATE. stopping at its end of the reverse side. DUAL REC cannot be used in this application; put The signal connected to DECK 1 is automatically both decks into Record Ready mode separately by routed to DECK 2. holding RECORD and pressing PAUSE on the individual decks. (The INPUT and REC BAL
ページ11に含まれる内容の要旨
Using a Single Unit You can press PAUSE on deck 2 to put deck 1 into 9. To stop dubbing in NORM mode and exit this Play Pause mode and deck 2 into Record Pause mode, press STOP on deck 2. In HIGH SPEED mode. mode, you can press STOP on either deck. Playback Using Just One of the Two Available Decks 1. Connect the amp/speaker system to the OUTPUT “ DOLBY NR switch depending on the tape in use. connectors of the deck you intend to use. 2. Insert the tape into either deck 1 or 2. If REV MODE i
ページ12に含まれる内容の要旨
Using a Single Unit Using the CPS Function CPS (Computer-controlled Program Search) 2. To autolocate the tape, say to the fifth program autolocates the tape to the beginning of specific ahead, press the CPS button repeatedly until 05 is program materials. The tape will automatically start displayed. Then, press F FWD. playing after completing autolocation. To identify specific programs, CPS counts a blank space of about 4 scconds between programs. To access a program on the other side of the tap
ページ13に含まれる内容の要旨
Multiple-Unit System Operation A maximum of ten compatible units (TASCAM 322 or “ Dubbing onto multipie cassettes simultaneously. 302MkII) can be interconnected to provide the “Recording an external source onto multiple following possibilities : cassettes simultaneously. “ Sequential link play of multiple cassettes. Sequential Link Play WARNING : Make all conncctions with power off. “ OFF/SLV/MSTR switch to OFF ; “ REV MODE switch to CONT. 5. Insert pre-recorded tapes into decks 1 and 2 of
ページ14に含まれる内容の要旨
Multiple-unit System Operation Simultaneous Dubbing onto Multiple Cassettes WARNING : Make all connections with power off. If the reverse PLAY LED is blinking on deck 1 of the master unit, press the Á on that deck. MASTER Bear in mind that, in a multiple-unit system, the transport control buttons on deck 1 of the master unit are independent from all the other decks, while the buttons on deck 2 of the master unit have effect on decks 1 and 2 of every slave unit SLAVE-1 6. If need be, rewind the
ページ15に含まれる内容の要旨
Multiple-unit System Operation 9. To start dubbing, press PLAY on deck 2 of the 10. To stop dubbing, press STOP on deck 2 of the master unit. Deck 2 of the master and all the slave master. decks will go into Record mode, simultaneously. NOTE Upon pressing STOP on deck 1 or deck 2 of any The target decks all configure themselves to the slave unit, that deck cannot function any more. Dolby system and the record level settings used To use it as a slave again, first press EJECT. when originally re
ページ16に含まれる内容の要旨
Multiple-unit System Operation 9. Adjust the INPUT control on deck 2 of the master 14. To continue to record, press the Ó button once so the meter reading is around 0 dB. Balance the more on deck 2 of the master. left and right input levels with the REC BAL control. 15. To terminate recording, press STOP on deck 2 of 10. Set the DOLBY NR switch on deck 2 of the master the master. to the desired position. All the slave decks configure themselves to the level and balance on deck 2 of the master.
ページ17に含まれる内容の要旨
Care and Maintenance Cleaning the Heads and Tape Guides All heads and metal parts in the tape path must be cleaned after every 6 hours of operation, or before starting and after ending a recording session. 1. Open the cassette compartment. 2. Using a good head cleaning fluid and a cotton swab, clean the heads and tape guides until the swab comes off clean. Wipe off any excess cleaning fluid with a dry swab. Cleaning the Pinch Rollers Clean the pinch rollers at least once each day the deck 2. Using
ページ18に含まれる内容の要旨
Troubleshooting Problem Possible Cause Solution REV MODE switch set to Ä or ä. Set switch to CONT. Continuous record/play OFF/SLV/MSTR switch set to SLV or impossible Set switch to the left OFF position. MSTR. Heads are dirty. Clean them, as stated above. Inappropriate DOLBY NR switch Set switch to the setting used for Poor sound quality setting. original recording. Heads are magnetized. Demagnetize them, as stated above. Erase-protection tabs broken off the Recording impossible Cover tab
ページ19に含まれる内容の要旨
Specifications Power Requirements : Tape : Compact cassette tape C-30/60/90 USA/Canada/General Export Model : (Normal/High Position/Metal) 120/230 V AC (50-60 Hz), switchable Track Format : 4-track, 2-channel U.K./Europe : 230 V AC (50 Hz) Head Configuration : 4-track, 2-channel ; Australia : 240 V AC (50 Hz) Record/repro combination rotary head Consumption : 33 Watts (DECK 1 x1, DECK 2 x1, permally) Dimensions : ( See drawings below) Erase head (DECK 1 x1, DECK 2 x1, ferrite) Weigh
ページ20に含まれる内容の要旨
Block Diagram TEAC CORPORATION Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan TEAC AMERICA, INC. Phone: (323) 726-0303 7733 Telegraph Road, Montebello, California 90640 TEAC CANADA LTD. Phone: 905-890-8008 Facsimile: 905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.A. De C.V Phone: 5-851-5500 Campesinos No. 184, Colonia Granjas Esmeralda, Delegacion lztapalapa CP 09810 Mexico DF Mexico TEAC UK LIMITED Phone: 01923-819699 5 Marlin
