ページ2に含まれる内容の要旨
W A R N I N G S Thank you for purchasing a Sirius Range Hood. Please read all the instructions in this manual before installing the appliance. Save these instructions for future reference. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the appliance. If the range hood is vented, the air so vented must be ducted into a dedicated duct that is not showed with any other
ページ3に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN 1 DUCTING 1 External Venting Requirements 1 Duct Run Calculation 1 ELECTRICAL 2 Electrical Supply 2 INSTALLATION 3 Positioning the Range Hood 3 Marking the Fixing Holes for the Range Hood 3 Fixing the Main Support Bracket 3 Chimney Installation 4 Hanging the Range Hood 4 Connecting Electricity and Ducting 5 Connecting Chimneys 5 Connecting the Screen (SU 202 only) 5 Re-Circulating Requirements 6 OPERATING PROCEDURES 6 General Advice 6 Functions 7 MAINTENANCE 7
ページ4に含まれる内容の要旨
BEFORE YOU BEGIN The manufacturer declines all BEFORE YOU BEGIN: responsibility in the event of failure It is advisable to test run the to observe the instructions given range hood before installation. here for installation, maintenance and suitable operation of the Please read this entire manual and product. The manufacturer further ensure that you are fully conversant declines all responsibility for injury with the requirements and limitations due to negligence and t
ページ5に含まれる内容の要旨
hood is 100’. Calculate your duct run Maximum Run by measuring linear feet and adding 6” or 3 1/4 x 10” duct 100 FT the elbows, transitions and caps Deduct based on the table alongside. Each 90 elbow used 15FT Each 45 elbow used 9FT The ducting connection to the hood Each 6” or 3 1/4 x 10” duct must be in line with the central vertical axis of the range hood 1” Transition used 1FT away from the back wall on which Each 3’1/4 x 10” to 6” the hood is to be mounted. Transition used
ページ6に含まれる内容の要旨
I N S T A L L A T I O N Gently tape the template to the wall Positioning the Range Hood making sure it has no creases or folds (use a tape that will not Determine the center point of the damage the wall finish). There are range hood. This is generally the three hole positions shown for the center of the range. Make a mark wall bracket. Using a sharp object, on the wall a minimum of 25” above mark the wall through the template the top of an electric range. If the at the cent
ページ7に含まれる内容の要旨
applications. Wherever possible, it Fix bracket “Y” to the wall and is advisable to place blocking ceiling. between the studs, behind the drywall, to attach the support bracket Hanging the Range Hood to (refer to Figure 4). Prepare the range hood for Drill the appropriate size holes at the installation. Remove all filters to marks made earlier and fix the ensure they do not get damaged Support Bracket (“S”) securely to during the installation process. Hang
ページ8に含まれる内容の要旨
These screws are also used to make minor adjustments to the levelling of the range hood. Ensure the hood is level. Locate the two holes “C” inside the housing of the range hood and secure the range hood to the wall once the range hood is perfectly level and vertical. (refer to Figure 3) Connecting Electricity and Ducting Figure 10 Figure 9 Connecting Chimneys Remove the protective covering from the decorative chimney and carefully Figure 8 slide the sections together. Please re
ページ9に含まれる内容の要旨
Figure 12 Figure 13 Figure 14 grit present – if there is this will most fit the deflector (refer Figure 13) with definitely crack the glass. The plastic the screws supplied to the upper washers must be positioned be- telescope chimney. tween the screw head and the glass. Fit the screen – please have some- There are holes in the back upper one hold this in place whilst another edge of the decorative chimney for person puts in the screws. Using this purpose. A short length of FINGER
ページ10に含まれる内容の要旨
NEVER dispose cigarette ashes, Functions ignitable substances or any foreign objects into blowers. Modular Wall Range Hood Controls Cooking that generates flame is not A: Light ON/OFF button recommended as this hood is B: Blower Speed 1 (low) or OFF equipped with a thermal overload C: Blower Speed 2 (medium) that will shut down the motor if it D: Blower Speed 3 (high) senses excessive heat. When E: Blower Speed 4 (intensive) frying, oil in the pan can easily F: 1
ページ11に含まれる内容の要旨
Allow filters to dry before replacing Light Bulb Replacement them, otherwise water will be drawn (If in doubt, call 866-528-4987) into the blower. Turn blower and lights off. Make If a carbon filter has been fitted, this sure the lights are cool. must be replaced every 6 months as a minimum, depending on usage Do not remove the entire fixture and type of cooking that is (socket) as this is very difficult to performed. reinstall. Gently pry the bulb from the fixture usin
ページ12に含まれる内容の要旨
Three Year Limited Warranty WARRANTY SERVICE To qualify for warranty service, you must notify Sirius Range Hoods at the address stated below or call toll free USA or Canada 1-866-528-4987 and provide the model number, description of the fault or defect and original date of purchase. Sirius reserves the right to request proof of original purchase. Sirius will at its sole option and discretion replace products that arrive damaged through shipping, provided shipping damage is reported
ページ1に含まれる内容の要旨
I N S T A L L A T I O N
I N S T R U C T I O N S
CARE AND USE MANUAL FOR:
CONTEMPORARY WALL RANGE HOODS
Models covered by these instructions:
SU202 & SU 207
* * * B E F O R E I N S T A L L A T I O N * * *
ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED
DURING SHIPPING
* * * S H I P P I N G D A M A G E * * *
MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT
Telephone (Toll Free): 866.528.4987 Fax (Toll Free): 866.365.9204
www.siriushoods.com
