GE EZ4の取扱説明書

デバイスGE EZ4の取扱説明書

デバイス: GE EZ4
カテゴリ: 水道システム
メーカー: GE
サイズ: 0.36 MB
追加した日付: 9/6/2013
ページ数: 33
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスGE EZ4の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、GE EZ4に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書GE EZ4をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書GE EZ4のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - GE EZ4の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
GE EZ4 取扱説明書 - Online PDF
Advertisement
« Page 1 of 33 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書GE EZ4を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書GE EZ4の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

OSMONICS
TM
E4, E4LE, EZ4 SERIES
WATER PURIFICATION
MACHINES
INSTALLATION, OPERATION,
AND MAINTENANCE
MANUAL
GE Infrastructure
Water & Process Technologies

ページ2に含まれる内容の要旨

ページ3に含まれる内容の要旨

INSTALLATION, OPERATION AND MAINTENANCE MANUAL E4, E4LE, AND EZ4 SERIES WATER PURIFICATION MACHINES TABLE OF CONTENTS Page 2.0 INSTALLATION 1 2.1 Mounting the Unit 1 2.2 Plumbing 1 2.3 Installing Clean-In-Place Valves 2 2.4 Concentrate Outlet Connections 2 2.5 Feed Water Requirements 2 2.6 Transporting Pure Water (Permeate) to Point-of-Use 3 2.7 Pressure Correction Factors 4 2.8 Electrical 5 2.8.1 Single-Phase Electrical 5 2.8.2 Three-Phase Electrical 5 2.9 Machine Control 6 2.9.1 Economy Model

ページ4に含まれる内容の要旨

Page 2.17 Operation and Maintenance 16 2.17.1 Daily Flushing for the Economy Model 16 2.17.2 Daily Flushing for the Deluxe Model 16 2.18 Pre-Filter Cartridge 17 2.19 Membrane Element Cleaning 17 2.19.1 Step Wise Cleaning 17 2.19.2 Procedure to Clean with a CIP Pump 17 2.20 Suction Cleaning 19 2.21 Changing Out Membrane Elements 20 2.22 Troubleshooting 22 LIST OF FIGURES Figure Description 2.1 Three-Phase Allen Bradley Motor Starter 6 2.2 Setting-Up the Correct Time on the Autoflush Timer 11 2.3

ページ5に含まれる内容の要旨

ページ6に含まれる内容の要旨

2.0 INSTALLATION 2.1 Mounting the Unit When installing your new GE Infrastructure Water & Process Technologies reverse osmosis (RO) machine, allow at least 45-inches (114 cm) above the machine for mem- brane element removal and loading. If space is not available, the entire membrane element housing can be removed for membrane element change outs. If the mem- brane element housings are to be removed to change out the membrane elements, at least 6-inches (15.2 cm) is required at the end of each

ページ7に含まれる内容の要旨

2.3 Installing Clean-In-Place Valves NOTE: Clean-In-Place (CIP) valves are not included with the machine. The CIP valves must be purchased and installed by the customer. When installing the CIP valves, a three-way valve should be installed in the inlet feed stream of the machine. The tees on the permeate and concentrate lines should be installed with two-way valves. All valves should be installed in a manner that will allow circulation of the cleaning chemicals through the machine and back to

ページ8に含まれる内容の要旨

Table 2.2 E-Series Feed Water Requirements Temperature Typical: 50° - 85°F (10° - 29°C) Limits: 33° - 104°F (0.16° - 40°C) Inlet Pressure Minimum: 30 psig (2.1 barg) Maximum: 60 psig (4.1 barg) Chlorine 0 parts per million (ppm) (continuous feed) Operating pH 5.5 - 8.5 Silt Density Less than or equal to 5 to minimize Index (SDI) membrane element fouling and extend cleaning intervals. Refer to ASTM* standard D4189. * American Standard for Testing Materials 2.6 Transporting Pure Water (Permeate) t

ページ9に含まれる内容の要旨

2.7 Pressure Correction Factors It is often necessary to operate RO machines with permeate back pressure. Permeate back pressure will decrease permeate production. See Table 2.3 (Pressure Correction Factors) to calculate loss of permeate. Table 2.3 Pressure Correction Factors PRESSURE % LOSS OF CORRECTION BACK PRESSURE PERMEATE FLOW FACTOR (PCF) E4/EZ4 E4LE E4/EZ4 E4LE 10 psig (0.7 barg) 5% 10% 0.95 0.90 20 psig (1.4 barg) 10% 20% 0.90 0.80 30 psig (2.0 barg) 15% 30% 0.80 0.70 40 psig (2.7 bar

ページ10に含まれる内容の要旨

2.8 Electrical This RO machine requires two supply voltages; the control voltage and the pump motor voltage. 2.8.1 Single-Phase Electrical The control voltage can be connected to either a 115 VAC, 60 Hertz or 220 VAC, 50 Hertz single-phase power supply. The RO control circuit should always be installed on at least a 15 Amp, single-phase dedi- cated circuit. Reverse osmosis machines with 115 VAC, single-phase control voltage include an eight-foot (2.4 m) cord which plugs into a three-prong grou

ページ11に含まれる内容の要旨

Figure 2.1 Three-Phase Allen Bradley Motor Starter 2.9 Machine Control 2.9.1 Economy Model To remotely control the Economy Model (ECN) with float switches and/or pre- treatment lockout, remove the jumper between terminals 4 and 5 and wire in the float switches or pretreatment components in series. After all field wiring is complete and complies with local and national electrical codes, move onto Section 2.10 (Pretreatment for Water Purification). NOTE: External control contacts are normally clo

ページ12に含まれる内容の要旨

and complies with local and national electrical codes, move onto Section 2.10 (Pretreatment for Water Purification). NOTE: External control contacts are normally closed, dry contacts. 2.10 Pretreatment for Water Purification A water analysis of your feed water should have been performed, as part of the plan- ning and engineering that went into developing your RO system. The water analysis will provide information on what type of pretreatment may be required and what recovery the machine can be r

ページ13に含まれる内容の要旨

6. Turn the ON/OFF button on the machine ON. System will open allowing water to flow through the machine to the drain through the permeate and concen- trate CIP valves. Let the machine run to drain for 5 - 10 minutes. This provides a wet start-up of the pump and removes any air in the system. 7. Turn the ON/OFF button on the machine to the OFF position. 8. Re-energize the pump power and trigger the ON/OFF button on the machine to check rotation of the pump motor. Observing from the back of th

ページ14に含まれる内容の要旨

The concentrate valve is drilled, and when completely closed the machine is running at the correct concentrate flow for a 75% recovery (Table 2.4, Flow Specifications for E4-Series Machines). If the temperature of the inlet feed water is not 77°F (25°C) use the Temperature Correction Factor Table (Technote 113). The proper adjustment of the recycle and concentrate valves are critical to the correct operation of the machine. CAUTION: Optimum recovery will vary according to water quality. 2.13 T

ページ15に含まれる内容の要旨

2.14 Recovery The machine flow specifications listed below are based on 25°C (77°F). Table 2.4 Flow Specifications for E4-Series Machines E4-Series 2200 4400 6600 11000 13200 8800 Recovery 50-75% 50-75% 50-75% 50-75% 50-75% 50-75% Units LPM/GPM LPM/GPM LPM/GPM LPM/GPM LPM/GPM LPM/GPM Permeate Rate 5.8/11.6 11.6/3.06 17.3/4.6 23.1/6.1 28.9/7.6 34.7/9.2 Concentrate 5.8/11.6 11.6/3.06 17.3/4.6 23.1/6.1 28.9/7.6 34.7/9.2 Rate (50%) Concentrate 1.9/0.5 3.9/1.0 5.8/1.5 7.7/2.0 9.6/2.5 11.6/3.06 Rate (

ページ16に含まれる内容の要旨

2.15 Autoflush Timer 2.15.1 Programming the Autoflush Timer The Autoflush timer clock operates and displays in real time, but the Autoflush feature will only work when the RO machine is operating. When the machine is operating in the Autoflush Mode, the total flow through the machine is increased. This provides extra cross flow which flushes the loose foulants from the surface of the membrane elements. When the machine is operating in the Autoflush Mode a slight drop in permeate production,

ページ17に含まれる内容の要旨

STEPS 1. While holding down the Clock Key ( ), press the h key to advance to ⊗ the current minute. 2. While holding down the Clock Key ( ), press the h key to advance to ⊗ the current minute. 3. While holding down the Clock Key ( ), press the h key to advance to ⊗ the current minute. NOTE: If the h and m keys are held down for longer than 2 seconds, the numbers will advance rapidly. If the days are flashing, it indicates the day of the week was not set when setting the time. The timer cannot be

ページ18に含まれる内容の要旨

2.15.4 Programming Twenty-Four Hour or Seven Day Schedules NOTE: It is helpful to write out the program schedules before programming the time. Example: Figure 2.3 Programming the Timer 2.15.5 Changing a Program Select the program to be changed with the Prog. Key. A new set of days may be selected with the Day Key just as in the initial programming. Hour and minute can be changed with the h and m Keys. 2.15.6 Deleting a Program To delete one or a few programs: Press the Prog. Key until the de

ページ19に含まれる内容の要旨

2.15.7 Troubleshooting the Autoflush Timer PROBLEM: Days are flashing, pressing any Key does nothing except “Hand” Key turns output ON and OFF. SOLUTION: Time of Day and Day of Week have not been set. See Section 2.15.3 (Setting-Up the Autoflush Timer Clock). PROBLEM: Time of day was set while holding the Clock Key down, but days are still flashing. SOLUTION: Current day of week was not set while holding down the Clock Key. See Setting-Up the Autoflush Timer Clock (Section 2.15.2). PROBLEM: It

ページ20に含まれる内容の要旨

2.16 Calibrating the Conductivity Probe STEPS 1. Make sure the calibration meter is in Measure Mode (with the MEAS LED light ON). 2. Immerse the Conductivity Probe in a 13.00 microSiemens (mS) prepared solu- tion. 3. Immerse and agitate Conductivity Probe, and wait for the reading to stabilize. 4. Calibrate the meter by adjusting the CAL adjustment screw until the Liquid Crystal Display (LCD) display reads 13 mS of the solution. The meter is now calibrated NOTE: The alarm function on the conduct


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 GE 215C1044P010-3 取扱説明書 水道システム 6
2 GE 268 取扱説明書 水道システム 17
3 GE 263 取扱説明書 水道システム 10
4 GE 3020511 取扱説明書 水道システム 1
5 GE E2 Series 取扱説明書 水道システム 2
6 GE 000 gpd to 288 取扱説明書 水道システム 0
7 GE E4H-CE Series, E8-CE Series 取扱説明書 水道システム 8
8 GE E4H Series 取扱説明書 水道システム 35
9 GE E4 取扱説明書 水道システム 62
10 GE EZ2 Series 取扱説明書 水道システム 0
11 GE E4LE 取扱説明書 水道システム 0
12 GE E8-CE 取扱説明書 水道システム 8
13 GE E4H-CE 取扱説明書 水道システム 0
14 GE Profile SmartWater ULTRA PLUS FQROPF 取扱説明書 水道システム 4
15 GE SmartWater GXRTQR 取扱説明書 水道システム 5
16 Sony 7 取扱説明書 水道システム 0
17 3Com ENTERPRISE OS 11.3 取扱説明書 水道システム 0
18 Acronis VIA C7-M 取扱説明書 水道システム 0
19 Acronis 200 Series 取扱説明書 水道システム 2
20 Acronis Z540 取扱説明書 水道システム 1