ページ1に含まれる内容の要旨
3.5 inch Hard Drive Enclosure
Model #: HDE350U
User’s Manual
ページ2に含まれる内容の要旨
Rev. 060811 2
ページ3に含まれる内容の要旨
User’s Record: To provide quality customer service and technical support, it is suggested that you keep the following information as well as your store receipt and this user’s manual. Date of Purchase: __________________________________ Model Number: __________________________________ Serial Number: __________________________________ Product Rev Number (located below the UPC on the package): __________________________________ 3
ページ4に含まれる内容の要旨
Package Contents: Your new Enclosure will ship with the following items. 3.5 inch Hard Drive Enclosure USB Cable Power Adapter Enclosure Stand Driver CD Mounting Screws User’s Manual Warranty Information System Requirements: Please be sure that you meet all of the system requirements below to avoid difficulties during installation. ® Windows 98SE, ME, 2000, XP Available USB 2.0 Port CD-ROM Drive (for driver installation) 3.5” Hard Drive (hard dr
ページ5に含まれる内容の要旨
USB Interface 5
ページ6に含まれる内容の要旨
Installation: 1. Removing The Inner From Your Enclosure: a. Remove the two screws from the connector end of your Enclosure. b. Slide the Hard Drive Tray out of your Enclosure. 6
ページ7に含まれる内容の要旨
2. Installing a Hard Drive Into Your Enclosure: a. Connect your 3.5” hard drive (not included) to the 4-Pin Power Connector and IDE connector on the Hard Drive Tray. b. Mount your hard drive to the Hard Drive Tray with two of the enclosed hard drive mounting screws. c. Inside your Enclosure you will notice an LED Power Cable, arrange the cable so the connector end is outside of the enclosure and then carefully begin to slide the Hard Drive Tray, with your hard drive attached, back into y
ページ8に含まれる内容の要旨
e. Secure the Hard Drive Tray to your Enclosure by using the screws removed in step 1a. 8
ページ9に含まれる内容の要旨
3. Connect Your Enclosure To Your Computer: a. Make sure the Power Switch on your Enclosure is in the OFF position. b. Turn on your computer and wait for it to load. c. Connect the USB Cable to the USB Port on your Enclosure, and then connect the other end to an available USB port on your computer. d. Connect the enclosed Power Adapter to the DC 12V Power Port on your Enclosure, and then connect the other end to a power outlet. e. Turn on the Power Switch on your Enclosure. f. Your com
ページ10に含まれる内容の要旨
® Special Instruction for Windows 98SE Users: ® In Windows 98SE, the “Add New Hardware Wizard” may open after your computer has detected your Enclosure. If this occurs, please follow the instructions below to install drivers from the enclosed Driver CD: 1. Insert the enclosed Driver CD into the CD-ROM drive of your computer. 2. At the “Add New Hardware Wizard”, click “Next”. 3. Select the option “Search for the best driver for your device (Recommended)” and then click “Next” to continue
ページ11に含まれる内容の要旨
4. Check ONLY the option “CD-ROM drive”, and then click "Next" to continue. ® 5. Windows will search and find the correct driver from the Driver CD, click “Next” to continue (NOTE: your computer ® ® may ask for your Windows 98SE CD during the installation; if this occurs, please insert your Windows 98SE CD and click “OK” to complete the installation). 11
ページ12に含まれる内容の要旨
6. After the installation is complete, click “Finish” to close the wizard. 7. Restart your computer (NOTE: if the following screen does not appear, please manually restart your computer). ® 8. After your computer has restarted and Windows is loaded, right-click “My Computer”, then click “Properties”, and then click the “Device Manager” tab. 9. Select “Disk Drives”. Your new hard drive will appear in the hard drive list. 10. Double-click your new hard drive and click the “Settings” t
ページ13に含まれる内容の要旨
11. Make sure there are check marks in the “Disconnect”, “Sync Data Transfer”, “Removable”, and “Int 13 unit” boxes. The drive letter will be automatically assigned to your hard drive. Click "OK", and then restart your computer. ® 12. Once your computer has restarted and Windows has loaded, your Enclosure will be ready to be used. 13
ページ14に含まれる内容の要旨
LED Indicators: There are LED Indicators located on your Enclosure, for a description and location of these LED indicators please refer to the picture and chart below: LED Indicator Status Description Power LED Off LED Power Cable Disconnected / Power Off On Connected / Power On Access LED Off LED Power Cable Disconnected / Power Off On Ready for Use Flash Data Transferring / Data Seeking 14
ページ15に含まれる内容の要旨
Formatting Your Hard Drive ® For Windows 98SE, ME If a new hard drive is being installed in your Enclosure, it will need to be formatted before it can be used. Please follow the instructions below. Please note that formatting a hard drive will delete ALL data from the hard drive and you MUST ® NOT format the hard drive that Windows is installed on. 1. Click “Start”, then “Settings”, then “Control Panel”. 2. Double-click on “System”, then “Device Manager”. 3. Select “Disk Drives”. Your n
ページ16に含まれる内容の要旨
6. After your system restarts, double-click the “My Computer” icon on your desktop. Right-click the hard drive icon for your removable disk and select “Format” from the menu. ® 7. Click “Start” and Windows will begin formatting your hard drive. Click “Close” when the formatting is complete. 16
ページ17に含まれる内容の要旨
8. Double-click the "My Computer" icon on your desktop, and you will see your new hard drive’s icon listed. Your new hard drive is now formatted and ready to be used. ® For Windows 2000, XP If a new hard drive is being installed in your Enclosure, it will need to be formatted before it can be used. Please follow the instructions below. Please note that formatting a hard drive will delete ALL data from the hard drive and you MUST ® NOT format the hard drive that Windows is installed on.
ページ18に含まれる内容の要旨
18
ページ19に含まれる内容の要旨
2. Right-click the status box of your new hard drive and select “New Partition”. 3. The "New Partition Wizard" will start, click "Next". Follow the onscreen instructions to complete the formatting. 19
ページ20に含まれる内容の要旨
4. Double-click the "My Computer" icon on your desktop. You will see your new hard drive’s icon listed. Your new hard drive is now formatted and ready to be used. 20
