ページ1に含まれる内容の要旨
WMT-3000
Wireless
Transmitter
Owner’s Manual
ページ2に含まれる内容の要旨
Warnings This device complies with Part 15 of the FCC rules, Operation of this device is subject to the fol- lowing conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation. Installation: The WMT-3000 transmitter is used with the Dakota Alert WR-3000 receiver. The WMT-3000 trans- mitter uses a passive infrared (PIR) detector to detect people, vehicles or large animals at the monitored l
ページ3に含まれる内容の要旨
PIR settings (figure 1) The jumpers settings are as follows: Range: High-80 feet Medium- 50 feet Low- 30 feet LED: ON- led will flash when it detects OFF- led is always dark Filter: On- set for outdoor use Off-set for indoor use Reset: 15 seconds to reset after activation 120 seconds to reset after activation Coding the transmitter: Note: The transmitters and receivers are preset at the factory. DO NOT change settings, unless changing the tune or experiencing false sig- nals. 1. When l
ページ4に含まれる内容の要旨
2. Locate the dip switches in the WMT-3000 transmitter module (figure 2). 3. The first eight dip switches are for the frequency setting (256 combinations). Set switches 1-8 (3) to match the eight switches in the receiver. 4. Switches 9 and 10 (4) are for the zone/channel settings on the transmitter. The four zones are listed in the table below. LOW BATTERY ALERT: If the receiver sounds a sec- ond alert 30 seconds after the first alert, provided nothing trips the transmitter again, the 9-vol
ページ5に含まれる内容の要旨
Mounting the transmitter: 1. Select a location to mount the transmit- ter, such as a post or tree. 2. For best results, the transmitter should be about three to four feet off the ground, and about twenty feet from the side of the drive. 3. The transmitter will detect people or ve- hicles to about eighty feet, but occasionally it may detect one hundred feet. For this rea- son, it is best to avoid pointing the transmit- ter at streets or roads in the distance. 4. The transmitter must remain c
ページ6に含まれる内容の要旨
Coding the receiver: 1. Open the receiver case by inserting a small screwdriver into one of the pry notches on the side of the case. (refer to receiver manual) 2. Gently lift off the front cover. 3. Locate the eight dip switches on the receiver and make sure they are set identically to dip switches 1-8 on the transmitter. Note: If more than one transmitter is used with the receiver, the first eight dip switches of all transmitters must match the eight dip switches of the receiver. Note:
ページ7に含まれる内容の要旨
Troubleshooting the WMT-3000 Although the WMT-3000 should be very reliable, there are occasions when you might have false alarms or a failure to alert. If you are getting false alarms, please try this: • S e t fi l t e r ju m p e r t o “ O N ” . • D e c r e as e r a n g e ju m p e r . • M a k e s u r e t h a t t h e t r a n sm i t t e r i s n o t p o i n t i n g a t a r o a d i n t h e d i s t a n c e . • T he sun ma y be causing false sig nals; tr y t o r eloca
ページ8に含まれる内容の要旨
WARRANTY Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of God or improper operation. If this product does become defective, simply return it to Dakota Alert. Please include a note describing the troubles along with your name and return address as well as the original sales receipt. If the product is covered under warranty it will b
