ページ1に含まれる内容の要旨
GALAXY
5000RS/2000RS
SERIES-DBP
DATA BUS PORT
VEHICLE SECURITY SYSTEM
WITH REMOTE START
PRODUCT MANUAL
ページ2に含まれる内容の要旨
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid. After the first 12 month warranty period there will be a maximum serv
ページ3に含まれる内容の要旨
Table of Contents 1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3 Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
About Your System The ScyTek Galaxy 5000RS-DBP Series is a Combination Vehicle Security and Remote Starting System , Galaxy 2000RS-DBP Series is a Remote Starting with keyless entry. featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come. The Galaxy’s 5000/2000RS Series built-in re
ページ6に含まれる内容の要旨
Remote Transmitters Standard Remote Transmitter Description LED LED Button 2 Button 1 Button 1 Button 2 Button 5 Button 3 Button 3 Button 4 Button 4 Button 5 T5 T5-SP Depending on the model chosen, the Galaxy 5000/2000RS-DBP Series will be supplied with one or two T5 or T5-SP 5-button Remote Transmitters that are used to control the system’s operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transm
ページ7に含まれる内容の要旨
Adding/Replacing Standard Remote Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter will be erased if it is not programed within the following sequence To program the transmitter(s): 1. Turn the ignition key On, Off, On, Off, and back On. (Key On 3 times) · 3 seconds
ページ8に含まれる内容の要旨
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Depending on the model chosen, the Galaxy 5000/2000RS-DBP-2W Series will be supplied with one or two 2-way LCD Remote Transmitters, offering increased range and confirmation of any activated features. Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks the sys
ページ9に含まれる内容の要旨
· The LED will illuminate. 3. Press and release Button 1 on the first transmitter then on the second transmitter. · The siren/horn will chirp/honk once for every transmitter learned. 4. Turn off the ignition key. 5. The siren/horn will chirp/honk 3 times to indicate the system has exited programming mode. LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. Depending on the amount of use, the battery m
ページ10に含まれる内容の要旨
To set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster. 4. When the desired time is displayed, press Button 5 to store. · The remote will beep 3 times to indicate the daily start function has been set. To disable the daily
ページ11に含まれる内容の要旨
CHP Set the siren/horn confirmation chirps/honks ON or OFF: 1. Press and hold Button 5 until the display shows CHP. ·The transmitter will beep three times. 2. Release Button 5. · The transmitter will beep once. · The LCD panel will show a siren if the chirps*/honks are enabled or "off" if the chirps*/honks are disabled. SND sound function selects the transmitter's confirmation mode - Tone or Vibration mode. Set the transmitter confirmation tones ON or OFF: 1. Press and hold Button 5 until the
ページ12に含まれる内容の要旨
Page 8 - Galaxy 5000/2000RS-DBP
ページ13に含まれる内容の要旨
O OP Pt tiio on na all C Co ollo or r R Re em mo ot te e time date/engine run timer 11/16 3:10P Button 3 Button 4 Button 5 wakeup Button 1 Battery autostart alarm Button 2 status enabled enabled Optional 2-way Color remote transmitter is offering increased range and confirmation of any activated feature. Page 1 Button 1 Arms and Locks* the system and when held for 3 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode
ページ14に含まれる内容の要旨
PAGER PARAMETERS SETTING Press and hold Buttons 2 and 3 until pager program features are displayed. Select pager setting by pressing buttons 1 or 2 to highlight the remote pager. Press button 3 to select the pager. Setting Date & Time Select Time Date setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Use buttons 1 & 2 to highlight the parameter you wish to change, use buttons 3 & 4 to scroll up or down to ch
ページ15に含まれる内容の要旨
Use buttons 1 & 2 to highlight the time parameter you wish to change, use buttons 3 & 4 to scroll up or down to chage the time. Save the changes by pressing button 5. START SET AUTO ST ON TIME: 08:00A Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Enable/Disable Alarm Select Alarm Clock on/off by pressing button 3. CLOCK ALARM ALARM ON TIME: 08:00A Use buttons 1 & 2 t
ページ16に含まれる内容の要旨
Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Press and hold Buttons 2 and 3 until pager program features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the siren. Press button 3 to select the system features. Siren Chirp Enable/Disable Select Siren Chirp setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to sel
ページ17に含まれる内容の要旨
Setting AutoStart Cold Temperature Threshold Select Cold Temp start setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. SIREN CHIRP PASSIVE ARM COLD TEMP HOT TEMP BACK Use buttons 3 & 4 to scroll up or down to chage the temperature threshold. Save the changes by pressing button 5. AUTOSTART SET COLD TEMP o TEMP: - 11 F Security system responce Setting AutoStart Hot Temperature Threshold Select Cold Temp Time setting by pressing buttons 1 or 2 to highlig
ページ18に含まれる内容の要旨
Synchronize System and Pager Clocks Select Clock Sync setting by pressing buttons 1 or 2 to highlight the arrows. Press button 3 to select the pager. Pager Clock Sync This feature synchronizes the pager clock to the security system time of a day clock. Select Pager Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. AUTO PGR CLK SYNC CLOCK SET SYS CLK SYNC START 1 TIME START 2 TIME Security system responce EXIT System Clock Sync This feature synchroni
ページ19に含まれる内容の要旨
START 1 SET SET TIME TIME: 8:00A Use buttons 1 & 2 to highlight Set Time press button 3. AUTOSTART 1 TIME: 8:00A The security system responce. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. PGR CLK SYNC SYS CLK SYNC START 1 TIME START 2 TIME EXIT Use buttons 1 & 2 to highlight hours or minutes, use buttons 3 & 4 to scroll up or down to chage the time. START 2 SET SET TIME TIME:
ページ20に含まれる内容の要旨
Programmable Functions using the Color Remote Programmable Functions using the Color Remote Pressing and holding transmitter button 5 will scroll through several transmitter programmable options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE, ENABLE AUTOSTART 1, ENABLE AUTOSTART 2. TEMPERATURE Check the temperature inside the vehicle 1. Press and hold Button 5 until the display shows TEMPERATURE 2. Release Button 5. · The transmitter will beep four times. ENABLE COLD ST
