ページ1に含まれる内容の要旨
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
ITEM 69054
60" Workbench
visit our website at: http://www.harborfreight.com
email our tech
ページ2に含まれる内容の要旨
SaFetY Setup OpeRatiOn maintenanCe t able of Contents Safety ......................................................... 2 Parts List and Diagram .............................. 10 Specifications ............................................. 3 Warranty .................................................... 12 Setup .......................................................... 3 WaRninG SYmBOlS anD DeFinitiOnS This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
ページ3に含まれる内容の要旨
Specifications Top Shelf Weight Capacity 250 lb. Drawer Weight Capacity 25 lb. (per drawer) Bottom Shelf Capacity 200 lb. Vise Capacity 7" Table Top Thickness 2-1/2" Setup - Before use: Read the entiRe impORtant SaFetY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 10. note: More than
ページ4に含まれる内容の要旨
SaFetY Setup OpeRatiOn maintenanCe 3. Once both Legs have been fastened to the Cross Brace, slide the Shelf (2) above against the Legs so that the far Cross Leg (4) edge fits onto the groove on the Cross Brace. Brace (3) See Figure C, right. Shelf (2) Figure C 4. While your assistant is holding the Shelf in place against the Figure 4 first Cross Brace, set the second Cross Brace against the other edge of the Shelf. See Figure D, right. Shelf (2)
ページ5に含まれる内容の要旨
6. Set the Sliding Partition (14) into place by inserting the tabs at the end of the Partition into the holes at the center of the Table Top’s underside. See Figure F, right. Sliding Partition (14) Table Top (1) Figure F note: Verify that the Sliding Partition and Table Top face the same direction. See Figure G, right. Sliding Partition (14) Table Top (1) Figure G 7. Use the Screws (13) to fasten the Sliding Partition to
ページ6に含まれる内容の要旨
SaFetY Setup OpeRatiOn maintenanCe 9. Use the Hex Wrench and Screws (6) to fasten the tops of the Legs to the Table Top underside. See Figure I, right. Leg (4) Hex Wrench (9) Table Top (1) Figure i 10. Use the Hex Wrench and Screws (13) to fasten the sides of the Legs to the Table Top underside. See Figure J, right. Leg (4) note: There are no pilot holes available for this step, so you will need to use a drill to make the pilot holes before thr
ページ7に含まれる内容の要旨
12. Once the ends of the Lower Support have been fastened to the Legs, use the Screws (6) to fasten the middle of the Sliding Lower Support to the top of the Sliding Partition. Partition (14) See Figure L, right. Lower 13. With assistance, set the assembled frame right-side up and Support in the spot where you want the Workbench located. (15) Figure l 14. Remove the Vise Screw and Washer (12) from the middle Vise (5) thread of the Vise (5). See Figure M
ページ8に含まれる内容の要旨
SaFetY Setup OpeRatiOn maintenanCe 17. Use the Drawer Screws (22) to fasten the Drawer Handles (21) to the Drawer Front Panels (16). See Figure O, right. Drawer Front note: Each Drawer piece should have a sticker designating what it Panel (16) is (P1-P5). Use the Parts List as on page 10 as reference. This will help assure correct assembly. Drawer Handle (21) Figure O Drawer Slot Panel (19) 18. Fasten the Drawer Panel (18) and the Drawer Slot Pan
ページ9に含まれる内容の要旨
20. Fasten Drawer Bottom to Drawer Pack Panel. Once Drawers are fully assembled, verify that the inside tracks along the Sliding Partition are pushed forward. See Figure R, right. Figure R 21. Slide Drawers into tracks along Sliding Partition and insides of the Legs. See Figure S, right. Drawer Front Panel (16) Figure S 22. Once all Drawers are inserted, tap Wood Pegs (10) and Wood Pegs (10) Small Anvil Pegs (11
ページ10に含まれる内容の要旨
SaFetY Setup OpeRatiOn maintenanCe parts list and Diagram pleaSe ReaD the FOllOWinG CaReFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS QUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRI
ページ11に含まれる内容の要旨
assembly Diagram Shelf (2) Table Top (1) Cross Brace (3) Vise (5) Leg (4) Screw (50mm) (6) Bolt (60mm) (7) Connecting Hex Wrench (50 mm) (9) Nut (8) Screw and Washer Wood Peg (10) Anvil Peg (11) (Washer not shown) (12) Lower Support (15) Screw (13) Sliding Partition (14) Drawer Screws (22) Drawer Back Panel - p2 (17) Drawer Panel - p3 (18) Drawer Slot Panel - P4 (19) Drawer Bottom - p5 (20) Drawer Front Panel - p1 (16) Drawer Handle (21) Record product’s Serial number here: note: If product h
ページ12に含まれる内容の要旨
limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installatio
