ページ1に含まれる内容の要旨
1” DRIVE INDUSTRIAL
AIR IMPACT WRENCH
94108
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2004 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight
ページ2に含まれる内容の要旨
Specifications Torque 1,250 FT./LBS. Working Pressure 100 PSI, 115 PSI = maximum air pressure Air Consumption 14 CFM Average Air Inlet 1/2 inch – 14 NPT with screen Drive One inch, Inline air impact; 6” extended anvil Regulator on Unit 3 torque settings: 1, 2, & 3; Left and Right direction Overall Dimensions 22” (L) x 8 1/4” (W) x 6 1/2” (H) with side handle Weight 25.8 LBS. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operati
ページ3に含まれる内容の要旨
Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and gre
ページ4に含まれる内容の要旨
Impact Wrench Safety Precautions 19. Only use Impact Sockets with this tool. Standard sockets will not withstand the force applied by this tool, and may break, possible causing personal injury and/or property injury. 20. Use only specified operating air pressure. Never operate tool above the recommended working pressure of 100 PSI. 21. Do not use combustible gases. Do not use combustible gases as a power source, or use tool in areas where combustible gases are stored. 22. OSHA Guidelines.
ページ5に含まれる内容の要旨
Assembly The only assembly required is to install Side Handle (8), per the following instruc- tions. Using Cap Screws (7), and the supplied Allen Wrench, mount the Side Handle (8) to the Front Casing (5). Securely tighten all Cap Screws (7). Note: Use pipe thread seal or Teflon tape on all threaded connections. Oiler and Filter Connection Dirt, water, and the lack of pneumatic tool oil are major causes for tool wear. It is recom- men
ページ6に含まれる内容の要旨
OPERATION NOTE: Turn off your air compressor and disconnect the air pressure hose before changing sockets or making any adjustments to this tool. Severe injury or property damage may result otherwise. WARNING: This tool generates considerable torque when in use. Always hold the tool with both hands when using, and brace yourself to resist the torque which will be delivered to the work piece. 1. Select the appropriate size 1” square drive socket (not included) for your needs. Push and
ページ7に含まれる内容の要旨
OPERATION (continued) Caution: Never increase pressure at the air compressor regulator to achieve more torque. 7. When finished, release the Trigger (36), and lift the Impact Wrench off the nut. 8. Remove the air supply hose, then squeeze the Trigger (36) again to release any remaining air pressure in the Impact Wrench air chamber. Maintenance 1. After each use, wipe the Impact Wrench with a clean cloth to remove any dirt and grease buildup. 2. To maintain tool life, always lubricate the air l
ページ8に含まれる内容の要旨
Parts List #205 Rotation / Torque Knob #60205 1 8 SKU 94108 For technical questions, please call 1-800-444-3353 Page 8
ページ9に含まれる内容の要旨
Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 94108 For technical questions, please call 1-800-444-3353 Page 9
ページ10に含まれる内容の要旨
Lubrication Gear oil should be added in part #4, use MoS2 lubricating grease. It should be added monthly. The amount is 0.033-0.044 lb. each time. Gear oil should be added in part #44, use Spindle Oil. Add 5-10 drops every day, before operating the tool. To take advantage of this warranty, the product 90 Day Warranty or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the Harbor Freight Tools Co. make
