Grindmaster CRATHCO 5711の取扱説明書

デバイスGrindmaster CRATHCO 5711の取扱説明書

デバイス: Grindmaster CRATHCO 5711
カテゴリ: 冷蔵庫
メーカー: Grindmaster
サイズ: 5.6 MB
追加した日付: 5/5/2013
ページ数: 72
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスGrindmaster CRATHCO 5711の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Grindmaster CRATHCO 5711に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Grindmaster CRATHCO 5711をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Grindmaster CRATHCO 5711のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Grindmaster CRATHCO 5711の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Grindmaster CRATHCO 5711 取扱説明書 - Online PDF
Advertisement
« Page 1 of 72 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Grindmaster CRATHCO 5711を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Grindmaster CRATHCO 5711の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

Crathco Beverage Freezers
®
Operation and Instruction Manual
for
Models 5311, 5511, 5941, & 5711
TABLE OF CONTENTS
Warnings and Safety Precautions.....................3
Installation ...................................................4-6
Operating and Adjustments .......................6-11
Care and Cleaning ...................................12-17
Maintenance Service ................................17-21
Troubleshooting .......................................22-23
Exploded Views................

ページ2に含まれる内容の要旨

ページ3に含まれる内容の要旨

WARNING LABELS OPERATOR'S SAFETY PRECAUTIONS 1) Read and understand the operating instructions in this manual thoroughly. 2) Note all warning labels on the freezer. If any of the warning labels are missing or damaged replace them immediately. 3) Do not wear loose fitting garments or jewelry which could cause a serious accident. 4) Stay alert at all times during operation. 5) Keep operating area clean. 6) Do not operate freezer if any excessive noise or vibration occurs. Contact your authorize

ページ4に含まれる内容の要旨

Removal from Carton and Pallet 1) Remove staples or cut cardboard box around the stapled area. 2) Pull the cardboard box up off machine. 3) Remove the Styrofoam packing and the plastic bag. 4) Remove both side panels with screwdriver. 5) Use a wratchet with a 3 inch extension and a 7/16 socket to remove the shipping bolts (connecting the machine to the pallet) located on both sides of the frame bottom plate. 6) Supporting all four sides, lift machine up and place in appropriate area. CAUTION:

ページ5に含まれる内容の要旨

Installation of Concealed Air Filter Accessory Kit (optional) (Part #s W089.0200 Stainless Steel, W089.0208 Black) 1) Remove the four screws that hold the right side panel on INSTALL THE FILTER PANEL OVER THE the machine. EXISTING SIDE PANEL & RE-INSTALL SCREWS. 2) Install the filter panel over the existing side panel and reinstall screws. (See Figure D) 3) Open top cover of filter cover by raising and rotating away from P/N: W0520101, COMES IN KIT # W0890220 the existing panel. FILTER PANEL F

ページ6に含まれる内容の要旨

Installation of Spinner/Mixer Accessory Kit (optional) (Part #W089.0053-115V) (Part # W0890124-220V) 1) Turn to "off" and unplug the freezer from the Electrical box electrical power source. 2) Remove the white plastic plugs covering the threaded holes on the right front panel (facing the freezer). 3) Remove the electrical box cover. 4) Feed the spinner electrical wires through the 7/8” hole in the spinner mounting bracket. 5) Feed these wires up through the 1/4” x 1/2” hole in the right side bot

ページ7に含まれる内容の要旨

Carburetor Assembly Your new freezer uses a metering device, known as a carburetor, to feed the proper ratio of mix and air into the freezing cylinder. For products such as dairy based shake mixes, the proper mix to air ratio is generally accepted to be two parts mix to one part air. This proportion yields a finished product that is both tasty and profitable. At this ratio, one gallon of liquid mix will yield a volume of one and one-half gallons of frozen product. The carburetor is a tube wit

ページ8に含まれる内容の要旨

Computing Overrun (cont.) 3) Draw a heaping cup of frozen product that contains no air pockets. Note: Use a spatula or other device to help fill the cup completely. Avoid tamping the cup as this artificially reduces overrun. 4) Use a straight edge to scrape off excess product flush with the rim of the cup and weigh the cup. 5) Subtract the cup weight and use the overrun formula to determine overrun. Weight of Weight of (Minus) x 100 = OVERRUN Liquid Mix Frozen Product Weight of Frozen Product

ページ9に含まれる内容の要旨

Mix Low Function (cont.) buzzer is out of the circuit and the light will illuminate fully again. After the 10-minute cycle the mix out safety func- tion is activated making the unit inoperable. The machine is placed into the standby mode to prevent any damage to the machine from running dry of product. The unit can be reset back to the freeze mode by simply adding mix into the hopper. 1) If the unit is low in mix or the unit shuts down due to extended mix low condition (“Mix Low” safety function

ページ10に含まれる内容の要旨

Product Consistency Adjustment (cont.) 4) When making adjustments to a thicker (colder) setting, dispense approximately 16 ounces (1/2 liter) of product and recheck consistency after the compressor has cycled off. 5) If the consistency is still not correct, repeat steps 2 and 3. "Standby" - Freezing Cylinder Temperature Adjustment 1) Remove the front electrical box cover. (See Figure C). 2) For a colder setting, turn the "Barrel" control adjuster, located at the top left of the circuit board, c

ページ11に含まれる内容の要旨

Consistency Control - Overview (cont.) In the “standby” mode the control board senses the temperature of the product in the barrel. The drive motor is cycled on time only. It will operate for 2 minutes ON then 18 minutes OFF as long as it is in “standby”. The com- pressor and drive motor are cycled independently for the barrel in the “standby” mode. Once the barrel thermistor signals to the board, the board will start the compressor and the barrel solenoid valve will open as refrigeration is req

ページ12に含まれる内容の要旨

CARE AND CLEANING Note: Each time the freezer is disassembled, all internal freezer components must be thoroughly washed, scoured, and sanitized using procedures recommended by your local health department. In lieu of local health department recommendations, use a three compartment sink; one compartment to wash parts in detergent, one compartment to rinse, and one to sanitize. Drain and Rinse 1. If the freezer is empty, proceed to “Cleaning Following Complete Disassembly of Unit” or “Daily Clea

ページ13に含まれる内容の要旨

Daily Cleaning Procedure (cont.) Note: The best way to remove an “O” Ring is to first wipe off all of the lubricant using a clean paper towel. Pinch the “O” Ring upward with a dry towel between your index finger and thumb. When a loop is formed in the “O” Ring, roll it out of the groove with your other thumb. Always remove the “O” Ring farthest from the end of the plunger first. (See figure M). Figure M Ring Removal 2. Take all components to the cleaning area. 3. Carefully inspect the “O” Ri

ページ14に含まれる内容の要旨

Sanitizing Carburetor and Valve Components (cont.) 8. Slide the valve plunger spring over the small end of the valve plunger and, using another clean piece of paper toweling, pick up the valve plunger at the outlet end and insert plunger and spring into the valve body (figure Q). 9. Push up on the valve plunger and insert the stainless steel handle (figure R). Figure Q Installing Plunger and Spring 10. Insert the dispensing valve handle retaining pin (figure S) Sanitizing and Refilling 1. Pour

ページ15に含まれる内容の要旨

Sanitizing and Refilling (cont.) 11. Watch the product flowing out of the dispensing valve and close the valve when the sanitizer remaining in the cylinder has been purged by the new mix. 12. Use a clean piece of paper toweling to insert the sanitized carburetor assembly into the inlet hole in the hopper (figure V). 13. Fill mix storage hopper with fresh product. Figure V Carb Tube 14. Turn front panel switch to “ON”. Allow approximately 20 to 30 minutes for the freezer to reach proper consi

ページ16に含まれる内容の要旨

Cleaning Following Complete Disassembly of Unit (cont.) IMPORTANT: After disassembly, thoroughly scour each part of the freezer in a warm mild detergent solution including the inside of the freezing cylinder and the mix storage hopper. Rinse each part with clear water. Prepare a minimum of 3-1/2 gallons (13 liters) of sanitizing solution (Divorsol CX or equiva- lent) following the manufacturer's instructions. Note: Add 3 ounces (85.4 mg) of Divorsol CX to 3-1/2 gallons (13 liters) of 120°

ページ17に含まれる内容の要旨

Reassembly (cont.) 5. Disassemble the carburetor assembly and remove the O-Rings. Wash and sanitize all parts. 6. Reinstall and lubricate the O-Rings and slip on the outer tube if equipped. (See Figure EE) Figure EE Thick product Standard Low overrun carb tube carb tube carb tube Sanitizing and Refilling 1. Prepare a minimum of 3-1/2 gallons (13 liters) of sanitizing solution (Divorsol CX or equivalent) following the manufacturer's instructions. Note: Add sanitizer to 3-1/2 gallons of water

ページ18に含まれる内容の要旨

How to Clean Exposed Filter: 1. Slide exposed filter out of the rails by pulling forward on the filter. It is recommended to remove the filter by using the palm of your hand and applying even pressure to the face of the filter. 2. Clean filter with liquid soap and water. 3. Soak filter for 15 minutes. 4. Rinse filter with heavy stream of water, opposite the direction of air flow. Allow filter to dry. 5. Slide the filter into the rails until the filter contacts the stop on the top rail. How to C

ページ19に含まれる内容の要旨

Annual Maintenance (cont.) 4. Remove dasher assembly, inspect stator bearings and replace shaft seal set. (See Care and Cleaning). 5. Remove rear panel and inspect "V" belt. 6. Inspect the drive shaft square hole for wear (rounding-out). 7. Check drive shaft and motor shaft bearings for excessive wear. 8. Reinstall side and back panels. 9. Re-connect power supply. Belt Adjustment CAUTION: Unplug the machine before performing any adjustments. This procedure  must be done by a qualified techni

ページ20に含まれる内容の要旨

5000 SERIES FREEZER SPECIFICATIONS: Specification Model 5311 Model 5511 Model 5711 Model 5941 Circuit NEMA# NEMA 5-20R NEMA 6-20R NEMA 6-20R NEMA 5-15R 208/230 volt, 60 Hz, 1 115 volt, 60 Hz, 1 Phase 208/230 volt, 60 Hz, 115 volt, 60 Hz, 1 Phase Electrical Phase Dedicated 20 Amp circuit 1 Phase 15 Amp circuit Dedicated 20 Amp circuit Drive Motor 1/4 hp, Capacitor Start/Run 1/2 hp, Capacitor Start/Run 1/2 hp, Capacitor Start/Run 1/4 hp, Capacitor Start/Run N/A Note: Freezer must be Compressor 3/


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Grindmaster CRATHCO 5311 取扱説明書 冷蔵庫 1
2 Grindmaster CRATHCO 5511 取扱説明書 冷蔵庫 0
3 Grindmaster 3312 取扱説明書 冷蔵庫 9
4 Grindmaster 6321L 取扱説明書 冷蔵庫 0
5 Grindmaster 3511 取扱説明書 冷蔵庫 0
6 Grindmaster CRATHCO 5941 取扱説明書 冷蔵庫 0
7 2JANE Surround Sound System HTS-GS1 取扱説明書 冷蔵庫 4
8 3Com Phaser 7750 取扱説明書 冷蔵庫 1
9 3Com iQ 10 取扱説明書 冷蔵庫 0
10 3Com PowerDual iQ 10 iQ 10C 取扱説明書 冷蔵庫 1
11 3Com PowerDual iQ 10 iQ 10P 取扱説明書 冷蔵庫 2
12 3Com Dell D-Family Battery Charger CHRG01L 取扱説明書 冷蔵庫 0
13 3Com PowerDual iQ 10 iQ 10PC 取扱説明書 冷蔵庫 0
14 3Com Preface Firmware Version 1.07 VFD-D D 取扱説明書 冷蔵庫 0
15 3D Connexion Infinity Systems Interlude IL120s 取扱説明書 冷蔵庫 1