ページ1に含まれる内容の要旨
Model CC4001 User Guide
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
ページ2に含まれる内容の要旨
LASER SAFETY CAUTION This unit employs a laser. Only a qualified service person should remove RISK OF ELECTRIC SHOCK the cover or attempt to service this device, due to possible eye injury. DO NOT OPEN CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, OTHER THAN THOSE SPECIFIED HEREIN DO NOT REMOVE COVER (OR BACK) MAY RESULT IN HAZARDOUS RADIATION NO USER-SERVICEABLE PARTS INSIDE EXPOSURE. REFER SERVICING TO QUALIFIED SERVICE PERS
ページ3に含まれる内容の要旨
to try to correct the interference by one or more of NOTE: IMPORTANT SAFETY the following measures: This equipment has been tested and found to – Reorient or relocate the receiving antenna. comply with the limits for a Class B digital device, INSTRUCTIONS pursuant to Part 15 of the FCC Rules. These – Increase the separation between the limits are designed to provide reasonable equipment and receiver. READ BEFORE OPERATING EQUIPMENT protection against harmful interference in a – Connect the equip
ページ4に含まれる内容の要旨
CONTENTS FOREWORD This section must be read before any connection is FOREWORD.....................................................................................................1 made to the mains supply. EQUIPMENT MAINS WORKING SETTING .............................................................................1 COPYRIGHT ............................................................................................................................1 INTRODUCTION ..................................
ページ5に含まれる内容の要旨
PLAYING MP3 FILES INTRODUCTION There are many sites on the Internet from which you can download music files in MP3 format. These files can be downloaded following the instructions on the site and stored on CD-R/RW discs which can then be played on the this unit. PRODUCT FEATURES APPLICABLE DISCS TO THE The music on commercially available music CDs can be converted into MP3 files on a computer using MP3 encoding programs. When this is done, the data is reduced to approximately 1/10 the original s
ページ6に含まれる内容の要旨
* Use discs which satisfy the CD standards INAPPROPRIATE PLACES such as those with the “CD logo” or BEFORE USING FOR INSTALLATION “” mark on their disc label surfaces. No guarantees are made for playback if discs To keep your player in perfect working order for the which do not satisfy the appropriate CD longest possible time, avoid installing the player in NOTES FOR REMOVING NOTES ABOUT THE DISCS standards are used. the following locations. SHIPPING SCREWS Similarly, no guarantees are made for
ページ7に含まれる内容の要旨
5 DISC CD CHANGER CC4001 OPEN/CLOSE PLAY STOP PAUSE D C K 1 2 3 4 5 IS S IP REPEAT RANDOM LEVEL STANDBY POWER ON/STANDBY PHONES 7 Cautions on handling power cord 7 Remote control USING REMOTE CONTROL UNIT LOADING BATTERIES Operate the remote control unit (RC4001CC) • Do not touch the power cord with wet hands. Batteries in this remote control unit have a life of within a distance of approx. 5 m from the infrared 7 Cautions on handling batteries • When disconnecting the power cord, always approxi
ページ8に含まれる内容の要旨
NAMES AND FUNCTIONS FRONT PANEL ⁄3 ⁄4 v b ⁄0 . , m OPEN/CLOSE PLAY STOP PAUSE 5 DISC CD CHANGER CC4001 1 MP3 CD PROGRAM RANDOM REPEAT 1DISC 2 R 12 345 DISC SKIP TRACK REPEAT RANDOM 3 DISC MIN SEC 1 2 3 4 5 4 6 7 8 9 10 TOTAL 11 12 13 14 15 5 EACH REMAIN 16 17 18 19 20 LEVEL STANDBY POWER ON/STANDBY PHONES x z c ⁄2 ⁄1 n ⁄5 ⁄6 z POWER ON/STANDBY button n 4/1, ¡/¢ , 7 STOP button ⁄3 1-5 (Disc Select button) (Track Skip/Search buttons) When it is pressed, the display window lights Press this button
ページ9に含まれる内容の要旨
NAMES AND FUNCTIONS DISPLAY WINDOW a b c def g h MP3 CD 1 PROGRAM RANDOM REPEAT 1DISC 2 R TRACK 3 n DISC MIN SEC 1 2 3 4 5 4 6 7 8 9 10 TOTAL EACH 11 12 13 14 15 5 REMAIN 16 17 18 19 20 m l k j i a 3 (Play) indicator h REMAIN indicator l Remote Control indicator This lights during disc play. This lights while displaying track and disc This lights during a remote control unit is remaining times. operated. b 8 (Pause) indicator i 1-20 (track number display) m Disc Number indicator This lights when
ページ10に含まれる内容の要旨
NAMES AND FUNCTIONS REAR PANEL REMOTE CONTROL ANALOG OUT ANALOG OUT DIGITAL OUT FLASHER IN IN L EXT. INT. RS-232C OUT R AC IN COAXIAL OPTICAL MODEL NO. CC4001 MODEL NO. CC4001 A B C DEFG H A EXT./INT. (External/Internal switch) C REMOTE CONTROL IN/OUT (input D ANALOG OUTPUT connectors F DIGITAL AUDIO OUT OPTICAL When this unit is used as a standalone and output) connectors These are the output jacks of the analog audio This jack is to be connected with a recording component, set this switch to t
ページ11に含まれる内容の要旨
NAMES AND FUNCTIONS REMOTE CONTROLLER z ON button n 1, ¡ (Search buttons) ⁄4 RECALL button When this button is pressed while the unit is in 1 : While this button is pressed during Use this button to check the programmed standby status, the power of the unit is turned playback, the track is searched tracks while programming or stopped z on. backward. programming. (See page 16) STANDBY ON ¡ : While this button is pressed during x playback, the track is searched x STANDBY button ⁄5 0 -9 (Numerical
ページ12に含まれる内容の要旨
NAMES AND FUNCTIONS Display Examples 7 Remote Control Unit Setting 7 CC4001 Setting REMOTE CONTROL CODE • When the remote control unit is set to CODE1 SETTING 1 CD STANDBY ON STANDBY ON 2 • The unit and remote control unit have five sets OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER 3 DISC 1 2 3 4 5 of built-in remote control codes for each. These 4 6 7 8 9 10 codes enable up to five CC4001s installed in 11 12 13 14 15 123 123 5 1-5 16 17 18 19 20 the same place to be controlled independently. 4
ページ13に含まれる内容の要旨
CONNECTIONS Depending on your amplifier/receiver/Stereo System, there are various ways to connect to this player. For correct connection please refer to instruction manuals of stereo system to be To Analog Audio output connected. Caution (white) (red) Do not connect audio output from this unit to PHONO input of your audio system. 1. Connect the audio cable q to this unit’s REMOTE CONTROL REMOTE CONTROL ANALOG OUT ANALOG OUT DIGIT DIGITAL AL OUT OUT FLASHER IN FLASHER IN Analog Audio outputs and
ページ14に含まれる内容の要旨
AC IN Caution 1. Press 0 OPEN/CLOSE button on the unit or remote control unit to open the disc tray. Hold • Place a disc on each tray correctly. If not, the OPERATION the edge of the disc and place on the tray. unit cannot be operated and discs may be damaged. • Be careful not to have your finger caught when CONNECTING THE POWER NORMAL PLAYBACK you close the tray. SUPPLY AND TURNING ON OPEN/CLOSE PLAY STOP PAUSE 5 DISC CD CHANGER CC4001 If the finger is caught, press 0 OPEN/CLOSE 12 345 DISC SKI
ページ15に含まれる内容の要旨
PAUSE PLAYBACK STOP PLAYBACK CHANGE DISCS WHILE PLAYING You can change other discs not being played while playing a disc. STANDBY ON r STANDBY ON OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER t e STANDBY ON 123 123 OPEN/CLOSE TIME DIMMER 456 456 0 OPEN/CLOSE 123 q w 789 789 PROGRAM RECALL PROGRAM RECALL 456 0 0 789 PROGRAM RECALL 0 8 PAUSE 7 STOP RANDOM AMS REPEAT RANDOM AMS REPEAT DISC 1 DISC 2 DISC 3 DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 RANDOM AMS REPEAT DISC 4 DISC 5 DISC 1 DISC 2 DISC 3 REMOTE
ページ16に含まれる内容の要旨
7 All Track AMS Play PLAYING YOUR FAVORITE PLAYING YOUR FAVORITE SEARCH YOUR FAVORITE Press AMS button on the remote control unit once TRACKS OF A DISC PARTS OF A TRACK TRACKS (AMS (AUTOMATIC to start AMS play all tracks automatically. MUSIC SCAN)PLAY) • At this time, “3” and “TRACK” blinks. AMS (Automatic Music Scan) play is a function to STANDBY ON STANDBY ON Blink play 10 seconds of each track’s beginning one by OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER CD one. 1 2 It is a useful function
ページ17に含まれる内容の要旨
7 All Disc AMS Play 7 Stop AMS Play 7 One Disc Random Play PLAYING TRACKS IN A Press AMS button on the remote control twice to To stop the AMS play, press the AMS button on When RANDOM button is pressed on the main unit RANDOM SEQUENCE start AMS play all discs automatically. the remote control unit once or twice until the or remote control unit once, starts the random play blinking “3” lights up. for one disc automatically. (RANDOM PLAY) • At this time, “3” and “DISC” blinks. • At this time, RAN
ページ18に含まれる内容の要旨
2. Press DISC1-5 button on the main unit or 7 One Track Repeat Play REPEAT PLAY PLAYING TRACKS IN A remote control unit or DISC SKIP button on the After choosing a track to repeat, press REPEAT SPECIFIC SEQUENCE Repeat play is a function to automatically play main unit to choose a disc where the tracks to button on the main unit or remote control unit once repeatedly. There are 3 modes for the Repeat play: register are contained. to play the chosen track repeatedly. (PROGRAM PLAY) • One Track Re
ページ19に含まれる内容の要旨
↓ BACK TO NORMAL PLAY CHECK THE PROGRAM CHANGE PROGRAMMED TRACKS Total playback time of the tracks programmed WITHOUT CLEARING PROGRAM (example) When tracks 3, 5, and 7 of disc 1 are programmed, 1 CD STANDBY ON To go back to normal play without clearing the PROGRAM change track 5 of disc 1 to track 7 of disc 3. 2 program while playing the program, do one of the TRACK OPEN/CLOSE TIME DIMMER 3 DISC MIN SEC followings: 4 7 5 123 STANDBY ON 456 STANDBY ON OPEN/CLOSE TIME DIMMER 789 • The programmed
ページ20に含まれる内容の要旨
2. Press DISC1-5 button on the main unit or 7 To Clear Chosen Track 7 To Clear Whole Program CLEAR PROGRAMMED TRACKS remote control unit or DISC SKIP button on the unit to choose disc 3. 7 To Clear One Track at a Time STANDBY ON STANDBY ON CD 1 OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER PROGRAM 2 STANDBY ON 3 0OPEN/CLOSE DISC 123 123 4 OPEN/CLOSE TIME DIMMER 5 456 456 123 789 789 PROGRAM RECALL PROGRAM RECALL 456 0 0 3. Press 4/1, ¡/¢ button on the main 1. 789 4¢ unit, or / or 1-9 button on t
