ページ1に含まれる内容の要旨
Planning Information
Integrated Model 700BR
Refrigerator Drawers
Seamless molding Removable crisper
cover
Location of serial Electronic digital
number control panel
Model 700BR
Magnetic drawer Upper refrigerator
gaskets storage drawer
Front venting with Lower refrigerator
removable kickplate storage drawer
These appliances are Star-K certified from the
factory to meet strict religious regulations in
conjunction with specific instructions found on
star-k.org. No extra wiring harness is required.
ページ2に含まれる内容の要旨
Planning Information Integrated Model 700BR FEATURES Drawer unit with refrigerator storage Alarm will let you know with an audible drawers beeping if a drawer is left open Integrated design for "point-of-use" refriger- Removable crisper cover with a clear-view ation anywhere in the home window can be used in either storage drawer Energy Star qualified Each storage drawer has a removable divider Refrigeration system ensures the freshest food and energy efficiency Meets strict Department of Energy
ページ3に含まれる内容の要旨
Planning Information Integrated Model 700BR SPECIFICATIONS Model 700BR Drawer Refrigerator Unit Overall Width 27" (686) 1 Overall Height 34 /2" (876) Overall Depth 24" (610) MODEL Refrigerator Capacity 5.3 cu ft (150 L) Drawer Refrigerator Unit 700BR Minimum Height (levelers in) 34" (864) 1 Drawer Clearance 19 /2" (495) PANEL OPTIONS Electrical Requirements 115 V AC, 60 Hz, 15 amp circuit Integrated (custom panels) Annual Energy Usage 337 kWh / $31 Classic Stainless Steel Finish /S (based on 9.0
ページ4に含まれる内容の要旨
Planning Information Integrated Model 700BR INSTALLATION SPECIFICATIONS TOP VIEW *PLACEMENT OF THE ANTI-TIP 1 1 1 /2" 13 /2" BRACKET* ANTI-TIP BRACKET (38) (343) SHOULD BE 24" (610) FROM THE FRONT OF THE 25" (635) UNIT WITHOUT PANELS TO THE BACK OF THE ANTI-TIP BRACKET. 27" 25" (686) (635) 1 34 /2" (876) NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO ANTI-TIP BRACKET PREVENT UNIT FROM TIPPING FORWARD FRONT VIEW SIDE VIEW LOCATE ELECTRICAL WITHIN SHADED AREA – ORIENT GROUND PRONG TO RIG
ページ5に含まれる内容の要旨
Planning Information Integrated Model 700BR INSTALLATION NOTES Refer to the illustrations and specifications Two Integrated units may be installed next to for overall dimensions, finished rough opening one another. Refer to page 10 for additional dimensions and installation specifics. information. IMPORTANT NOTE: The depth of Model 700BR A 115 volt, 6OHz, 15 amp circuit breaker and is 24" (610) from the front of the unit to its electrical supply are required. A separate circuit, back. Your desig
ページ6に含まれる内容の要旨
Planning Information Integrated Model 700BR CABINETRY APPLICATIONS Integrated refrigeration is compatible with virtually any style and look of cabinetry. The models can be used with framed as well as frameless cabinets. Because of the precise application and the look you may want to achieve, there are important questions you need to answer before ordering panels for the drawers. As you look at styles of cabinets, keep some important facts in mind: IMPORTANT NOTE: The depth of each Integrated uni
ページ7に含まれる内容の要旨
Planning Information Integrated Model 700BR FRAMED CABINETRY APPLICATIONS Framed cabinetry applications present you with different questions to address. The illustrations on this page show common applications of framed cabinetry. These are not meant to be the only alternatives, but are suggestions from designers around the country. FRAMED CABINETRY IMPORTANT NOTE: The depth of each Integrated unit is 24" (610) from the front of the unit to its back. You must allow for the thickness of the panel
ページ8に含まれる内容の要旨
Planning Information Integrated Model 700BR FRAMED CABINETRY – BEADED INSET APPLICATION The illustration shows an Integrated drawer unit installed within a framed cabinetry beaded inset 24" (610) application. SUB-ZERO TO WALL CABINET DOOR UNIT 1 IMPORTANT NOTE: Dimensions are based on a /8" (3) 1 reveal. A reveal of up to /4" (6) is possible, but panel dimensions need to be adjusted accordingly. PANEL A A 27" TOP VIEW (686) A) ALL REVEALS ARE 1/8" (3) B) DRAWER RAILS ARE ATTACHED TO DRAWER FR
ページ9に含まれる内容の要旨
Planning Information Integrated Model 700BR FRAMELESS CABINETRY APPLICATIONS The illustration below shows a hypothetical installation of an Integrated drawer unit within frameless cabinetry. Review the illustration, giving particular attention to the overall panel specifications. 1 IMPORTANT NOTE: Dimensions are based on a /8" (3) 1 reveal. A reveal of up to /4" (6) is possible, but panel dimensions need to be adjusted accordingly. FRAMELESS CABINETRY 3 24" 26 /4"* (679) (610) PANEL WIDTH A 9 13
ページ10に含まれる内容の要旨
Planning Information Integrated Model 700BR CABINETS 25 (635) INSTALLATION OPTIONS 27 (686) The illustrations on this page show some typical TOP VIEW installations and their dimension considerations. The depth dimension in the illustrations may vary Installation without side panels. 2 depending on cabinet styles, treatment of counter- tops or other design options. C IMPORTANT NOTE: The depth of each Integrated CABINETS unit is 24" (610) from the front of the unit to its back. Your design may nec
ページ11に含まれる内容の要旨
Planning Information Integrated Model 700BR TOE KICK CLEARANCE The toe kick clearance can vary with the height of the 11 lower drawer panel; the maximum panel height is 16 /16" (424). IMPORTANT NOTE: You must keep a minimum space of 4" (102) clear below the bottom edge of the lower drawer panel so the unit can be properly vented. In addition, any decorative base molding must be removable for possible servicing and cleaning of the condenser. The illustration below shows the area below the lower
