ページ1に含まれる内容の要旨
ENGLISH FRANÇAIS
9A10350000
Z
-
CD RW880
CD Recorder
OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- 3) Heed all warnings. SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 4) Follow all instructions. The lightning flash with arrowhead symbol, within an 5) Do not use this apparatus near water. equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within
ページ3に含まれる内容の要旨
ENGLISH This product has been designed and manufactured according to WARNING: TO PREVENT FIRE OR SHOCK FDA regulations “title 21, CFR, chapter 1, subchapter J, based on HAZARD, DO NOT EXPOSE THIS APPLIANCE the Radiation Control for Health and Safety Act of 1968“, and is TO RAIN OR MOISTURE. classified as class 1 laser product. There is not hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the CAUTION pr
ページ4に含まれる内容の要旨
Contents Before using the unit Thank you for choosing TEAC. Read this manual carefully Read this before attempting any operations to get the best performance from this unit. < The nominal temperature should be between 5°C and 35°C (41°F and 95°F). The CD-RW recorder is more sensitive to Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 2 extremes of temperature than ordinary CD players. Before using the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ5に含まれる内容の要旨
ENGLISH Connections CAUTION: < Switch off the power to all equipment before making connections. < Read the instructions of each component you intend to use with this unit. < Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord. B A C RL RL DIGITAL OUT REC PLAY AC Outlet CD Player, MD Deck, etc. Amplifier A ANALOG IN/OUT jacks Analog 2-channel audio signal is input or output from these jacks. Connect these
ページ6に含まれる内容の要旨
Discs Please use CD, CD-R and CD-RW discs bearing the < Should the disc become dirty, wipe the surface radially (from “DIGITAL AUDIO” logo. the center hole outward towards the outer edge) with a soft, dry cloth: CD CD-R CD-RW < Never use such chemicals as record sprays, antistatic sprays or fluid, benzine or thinner to clean the discs. Such chemicals will do irreparable damage to the disc’s plastic surface. < Discs should be returned to their cases after use to avoid dust and scratches that coul
ページ7に含まれる内容の要旨
ENGLISH Remote Control Unit The provided Remote Control Unit allows the unit to be About CD-R and CD-RW discs operated from a distance. CD-R discs can be recorded once only. Once they have been When operating the remote control unit, point it towards the used for recording, they cannot be erased or re-recorded. REMOTE SENSOR on the front panel of the unit. However, if space is available on the disc (and the disc has not been finalized), additional material can be recorded. < Even if the remote c
ページ8に含まれる内容の要旨
Unit Functions and Remote Control A B C D E F G H I Q P O N M L K J A E F B G H I C I J D J H F G 8
ページ9に含まれる内容の要旨
ENGLISH A Q POWER Remote Sensor Press this button to turn the unit standby or off. When operating the remote control unit, point it towards the REMOTE SENSOR. The equipment draws a nominal amount of power from the AC outlet even with its POWER switch in the OFF position. A STANDBY/ON When the POWER switch of the main unit is depressed, use this button to turn the unit on or standby. B Display B Numeric buttons C Disc Tray Use these buttons to select track numbers. D OPEN/CLOSE C REPEAT (1/ALL, A
ページ10に含まれる内容の要旨
Listening to a CD 5 Press the OPEN/CLOSE button (L) to close the tray. 4 3 6 5 1 < It takes a few seconds for the unit to load the disc. No buttons will work during loading. Wait until the total number 1 Press the POWER switch. of the tracks and the total play time of the disc are displayed. The unit enters standby mode, and “STAND-BY” lights on the display. disc type indicator 2 Press the STANDBY/ON button of the remote control unit to turn the unit on. total number of the tracks total play tim
ページ11に含まれる内容の要旨
ENGLISH Standby mode To skip to the next or a previous track When the POWER switch of the main unit is depressed, use During playback, repeatedly press the MUSIC SKIP button this button to turn the unit on or standby. (.or/) until the desired track is found. The selected track will be played from the beginning. If one of the following buttons is pressed in the standby mode, the unit will also turn on: In the stop mode, press the SKIP button (.or/) repeatedly until the track you want to listen to
ページ12に含まれる内容の要旨
Direct Playback Time Display While in stop or playback mode, you can use the numeric Each time the TIME button is pressed, the display changes as buttons of the remote control unit to select a track. follows: Press the numeric buttons to select a track. Playback starts from the selected track. CD/CD-R/CD-RW playback To play tracks 1 through 9, simply press the appropriate button (1 through 9). To play a track whose number is higher than 9, press the +10 elapsed time of current track button appro
ページ13に含まれる内容の要旨
ENGLISH Repeat Playback A-B Repeat Each time the REPEAT button is pressed, the repeat mode is To repeat a designated section changed as follows: Please note that CD-R/CD-RW discs that haven't been finalized cannot be used for A-B repeat. REPEAT ALL REPEAT 1 (off) 1. Start playback and designate the point at which the A-B repeat should start (point A) by pressing the A-B REPEAT ALL (Repeat All the Tracks) button. Press the REPEAT button once during playback. “REPEAT A-” blinks on the display. All
ページ14に含まれる内容の要旨
Programmed Playback 3 Up to 32 tracks can be programmed in the desired order. When the selection of track numbers has been finished, press the PLAY button (y) to start program playback. < Insert a disc before beginning programming. < Shuffle playback does not work during programmed playback. < Programmed playback works with finalized discs only. 1 Press the PROGRAM button in the stop mode. “PROGRAM” indicator blinks, and “0P00” appears on the display. 2 Press the numeric button to select a track
ページ15に含まれる内容の要旨
ENGLISH Before Recording Before you start recording, make sure that you understand To check the programmed order the following points: In the stop mode, press the PROGRAM CHECK button repeatedly to show the track numbers that have been stored < The unit requires Digital Audio CD-R or CD-RW media for in memory. recording. Computer CD-R or CD-RW discs do not work with this unit. < Once you have recorded on a CD-R disc, the data cannot be erased from it. < You can add tracks to an unfinalized recor
ページ16に含まれる内容の要旨
Recording 4 Press the RECORD button. 1 6 4 3 2 5 and J indicators on the display will light, and the unit enters record pause mode. 1 Load a recordable CD-R or CD-RW disc into the unit. < No button will work while “WAITING” is displayed. Wait a few seconds until “WAITING” disappears from the display. 2 When DIGITAL is selected in step , the sampling frequency of the digital source (“FS 44_1K”, “FS 48K” or “ FS 32K”) briefly appears after “WAITING”. < “DIN UNLOCK” appears when the unit cannot pe
ページ17に含まれる内容の要旨
ENGLISH Manual track division 6 Press the PLAY or the PAUSE button to start recording. It is possible to divide the recording into tracks while recording. While recording is taking place, press the RECORD button. The current track number will be incremented by one. 7 Play the source to be recorded. When the playback of the source has been finished, press the STOP button to stop recording. < The STANDBY/ON button doesn’t work during recording. < Manual track division is possible regardless of the
ページ18に含まれる内容の要旨
Automatic Track Division . A TRACK (–60, –50, –40 or –30 dB) When recording digitally, the unit will automatically insert a track division in the recorded material when an increment signal is detected. When the digital source doesn’t contain increment signals, or when recording analogically, the unit will automatically insert a track division in the recorded material when sound level has dropped below the increment level (–60, –50, –40 or –30dB) When the AUTO/MANUAL button is pressed once, the c
ページ19に含まれる内容の要旨
ENGLISH Synchronous Recording 2 Synchronous recording means that recording will begin Press the RECORD button. automatically when a signal is received, and will stop when the signal ends. The conditions under which an input signal is used as the trigger to start recording are: when recording a CD digitally, a digital start signal is detected, and audio is also detected or The unit enters record pause mode. when recording an MD or DAT digitally, a digital start signal is detected < The PLAY or th
ページ20に含まれる内容の要旨
Finalize 3 Press the PLAY (y) button to start finalizing. 1 3 2 “TOC” and the “REC” indicator blink, and the remaining This section deals with the actions taken after recording. time for the finalizing operation appears in the display. Once finalized, CD-R discs are truly final. No more tracks can When the operation has been finished, the display returns to be recorded on them. By contrast, CD-RW discs can be the track/time display. “unfinalized”, and if there is space, further material can be r
