ページ1に含まれる内容の要旨
OWNER'S MANUAL
JOVS-10 Oscillating Spindle Sander
WMH TOOL GROUP
Consumer/Light Industrial Products Division
P.O. BOX 1349
Auburn, WA 98071-1349
Ph: 1-800-274-6848 ▪ Fax: 1-800-274-6840
E-mail: jet@wmhtoolgroup.com
www.wmhtoolgroup.com M-708411 11/02
Copyright © WMH Tool Group
ページ2に含まれる内容の要旨
This manual has been prepared for the owner and operators of a JOVS-10 Sander. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your JET Sander, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warranty
ページ3に含まれる内容の要旨
WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. This sander is intended to be used with wood and wood products only. Use of this sander and a dust collector with metal products is a potential fire hazard. Support the workpiece adequately at all times during operation; maintain control of the work at all times. This sander is designed and intended for use by properly trained
ページ4に含まれる内容の要旨
• ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. • NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. • CHECK DAMAGED PARTS. Before further use of the machine, a guard or other pa
ページ5に含まれる内容の要旨
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local
ページ6に含まれる内容の要旨
Specifications JOVS-10 Stock Number................................................................................................................................ 708411 Table Size ..............................................................................................................................24”W x 24”L Table Tilt (down)...................................................................................................................................45° Dust Chute Diameter ..
ページ7に含まれる内容の要旨
Contents of the Shipping Container 1. Sander 3. Table Insert Rings 2. Spindle Wrenches 1. 2mm Hex Wrench 10 Removable Spindles 1/4” x 5” Steel and Sanding Sleeve 3/8” x 6” Steel and Sanding Sleeve 1/2” x 6” Steel and Sanding Sleeve 5/8” x 6” Steel and Sanding Sleeve 3/4” x 9” Steel and Sanding Sleeve 1” x 9” Rubber and Sanding Sleeve 1-1/2” x 9” Rubber and Sanding Sleeve 2” x 9” Rubber and Sanding Sleeve 3” x 9” Rubber and Sanding Sleeve 4” x 9” Rubber and Sanding Sleeve 1 Ow
ページ8に含まれる内容の要旨
Mounting Sanding Sleeves 1. Thoroughly clean the arbors (A, Fig. 1) on all of the spindle assemblies. Also clean the arbor housing on the sander. 2. Slip the sanding sleeve (B, Fig. 1) over the spindle and hold in place by tightening the set screw (C, Fig. 1) with the supplied 2mm hex wrench. 3. Repeat for all of the steel spindle assemblies. 4. To protect the sanding assemblies place them in the holders found on the sides of the sander, see Figure 2. Installing Sandi
ページ9に含まれる内容の要旨
Table Insert 1. Disconnect the sander form the power source, unplug. 2. Choose the insert (A, Fig. 4) that most closely matches the diameter of the sanding drum. 3. Line up the notch in the insert with the spring pin in the table (B, Fig. 4), and press in place. 4. Remove the insert by pressing up from underneath. Note: Keep the opening in the table clean so that the insert can be easily put in place, and removed. Sanding Assembly 90° to Table 1. Loosen the lock kn
ページ10に含まれる内容の要旨
Replacing Sanding Sleeves 1. Loosen hex nut (A, Fig. 7) with a 26mm wrench, or large adjustable wrench. 2. Slide the sanding sleeve (B, Fig. 7) off the drum and replace with a new sanding sleeve. Note: If the sanding sleeve is not easily removed cut the sleeve off and clean the drum before reinstalling a new sleeve. 3. If you are replacing the sanding sleeves on the steel spindles loosen the set screw found on the arbor nut. 4. Remove sanding sleeve from the spindle and r
ページ11に含まれる内容の要旨
Troubleshooting Trouble Possible Cause Solution 1. Sander unplugged from wall 1. Check all plug connections or motor 2. Replace fuse or reset circuit 2. Fuse blown or circuit breaker breaker Sander will not start tripped 3. Replace cord 3. Cord damaged 4. Replace starting capacitor 4. Starting capacitor bad 1. Extension cord too light or 1. Replace with adequate size Sanding drum does not come too long and length cord up to speed 2. Low current 2. Contact a qualified electrician
ページ12に含まれる内容の要旨
Breakdown for the JET Oscillating Spindle Sander 12
ページ13に含まれる内容の要旨
Parts List for the JET JOVS-10 Oscillating Spindle Sander Index Part No. No. Description Size Qty. 7..........OVS10-007 .................. Power Cord ........................................... ...............................................1 11........KEY5525...................... Key........................................................ ...............................................1 18........OVS10-18.................... Oil Indicator ........................................
ページ14に含まれる内容の要旨
Index Part No. No. Description Size Qty. ............JOVS10-147RC ........... Running Capacitor (not shown) ..............45uf, 250V ..............................1 ............JOVS10-147SC............ Starting Capacitor (not shown)...............300MFD, 125VAC...................1 148......JOVS10-148 ................ Strain Relief Bushing ............................. ...............................................1 149......TS-0720081 ................. Lock Washer.....................
ページ15に含まれる内容の要旨
Sanding Assemblies 15
ページ16に含まれる内容の要旨
Sanding Assemblies Index Part No. No. Description Size Qty. 93........OVS10-093 .................. Wrench.................................................. ...............................................2 94........OVS10-094A................ Arbor .....................................................3/4” .........................................6 95........OVS10-095 .................. Hex Nut ................................................. ..........................................
ページ17に含まれる内容の要旨
Index Part No. No. Description Size Qty. 130......575800......................... Sanding Sleeve (100 Grit)......................1/4” ........................................... ............575801......................... Sanding Sleeve (120 Grit)......................1/4” ........................................... 133......OVS10-133A................ Spindle .................................................. ...............................................1 165 ......JOVS10-165 .......
ページ18に含まれる内容の要旨
Wiring Diagram 18
