ページ1に含まれる内容の要旨
Airless Paint Sprayer
Item 68001
Read this material before using this product.
Failure to do so can result in serious injury.
SAve thIS mAnuAl.
Notice
CleAn ImmedIA tely
Clean the Sprayer ImmedIAtely after use.
delayed or inadequate cleaning will
permanently clog the Sprayer.
Warranty void if sprayer is not
properly cleaned immediately
after every use.
See “Cleaning” on pages 16-17.
When unpacking, make sure that the product is intact and undamaged.
If any parts are missing or broken, ple
ページ2に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. Save this manual Symbol Definitions Keep this manual for the safety warnings and precautions, Symbol Property or statement assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number on the Pounds per square inch of pressure PSI front page of the user’s man
ページ3に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 3. Personal safety Safety Warnings a. Stay alert. Watch what you are doing and use common sense when operating the sprayer. Do not use the sprayer while tired or under WARnInG Read all safety warnings the influence of drugs, alcohol, or medication. and instructions. Failure to follow the warnings
ページ4に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. sprayer’s operation. If damaged, have the 9. do not use Paint Sprayer to spray sprayer repaired before use. Many accidents asbestos, metallic paints, glazes, are caused by poorly maintained sprayers. red lead, cement, ground chalk, abrasive grainy paints containing lime, or bleach. f. use the spra
ページ5に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 24. Remove Spray Tip or turn to cleaning position 31. WARNING: Some dust created by power BEFORE cleaning or flushing Paint Sprayer system. sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known 25. Do not use pliers to tighten or loosen [to the State of Cali
ページ6に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. extension Cords Grounding 1. Grounded sprayers require a three wire extension cord. Double insulated sprayers can use either a two or three wire extension cord. tO PRevent eleCtRIC ShOCK And 2. As the distance from the supply outlet increases, you deA th FROm InCORReCt must use a heavier gauge exte
ページ7に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current v~ Amperes A No Load Revolutions n xxxx/min. 0 per Minute (RPM) SKU 68001 For technical questions, please call 1-800-444-3353. Page 7
ページ8に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. Before you Begin Familiarize yourself with the Paint Sprayer and its functions. Handle Suction Tube ON/OFF Switch (Not Shown) Return Tube Pressure Control Knob Paint Hose Outlet Filter Prime/Spray Switch Power Cord Spray Tip Hanging Hook Spray Gun Spray Tip Guard Trigger Lock Trigger Guard Trigger Pa
ページ9に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. Prime/Spray Switch This switch toggles the unit between Prime Spray priming mode and spraying mode. locked unlocked t rigger lock When engaged, this mechanism prevents the trigger from being pulled accidentally such as if the gun is dropped. lock whenever not in use. Spray / Clean / eject nozzle The
ページ10に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 2. Attach Paint Hose to Paint Gun and Setup tighten with two wrenches. note: Remove or cover objects that you want to protect from overspray (paint mist). 1. Attach Paint Hose to Paint Hose Outlet and tighten with wrench. 3. Turn Pressure Control Knob to Low Pressure Spray setting. Page 10 For techn
ページ11に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 4. Turn Trigger Lock Knob to Locking position. t o Relieve Sprayer Pressure 1. Turn Power Switch off and unplug unit from outlet. 5. Switch Prime/Spray switch to Prime mode. 2. Switch Prime/Spray switch to Prime mode. 3. Point gun into paint pail and activate Sprayer Trigger to relieve pressure. SKU 680
ページ12に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 4. Turn Prime/Spray switch to Prime mode. Priming Spray Gun This procedure is used for first time operation and also to flush storage fluids out of the Sprayer. Priming Water-Based vs. Oil-Based Paints Oil-based Paint: Flush with mineral spirits followed by warm clean water. WARnInG! t O PRevent
ページ13に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 8. Remove Suction Tube from water or flushing 11. Turn Spray/Prime Switch to Spray mode and solvent and submerge in paint pail. continue to spray into waste bucket. 9. Switch Power to On. 12. Stop spraying and activate trigger lock. 10. Paint should work itself from Suction Tube to Sprayer to Return Tu
ページ14に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. Painting Painting t echniques Before painting, ensure the Sprayer has been primed Before painting, ensure the Sprayer has been primed (see Priming and Startup steps) and verify (see Priming and Startup steps) and that Nozzle Tip is aligned properly. verify that Nozzle Tip is aligned properly. Keep t
ページ15に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 5. Unlock Trigger. Clearing Spray t ip Occasionally, the Spray Gun Tip will become clogged with paint. Follow these instructions to clear Spray Gun Tip. 1. Switch power off and set Trigger Lock. 6. Spray into waste bucket until clog clears. 2. Adjust nozzle to clean setting. 7. Release Trigger and engag
ページ16に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 5. Unthread Spray Tip and remove. Cleaning 1. Relieve pressure and drain paint from Tubes. 6. Turn to Spray mode. 2. Separate tubes. 7. Switch power to on. 3. Place Return Tube in empty waste bucket. 8. Spray paint into paint pail. 4. Submerge Suction Tube in water or flushing fluid. Page 16 For technica
ページ17に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. 9. Change to waste bucket as paint thins. 13. Remove trigger guard from housing. 10. Turn to Prime mode. 14. Unscrew nut. 11. Continue to flush until clear. 15. Remove filter. 16. Clean all parts in warm, soapy water or 12. Release trigger, turn power off, and relieve pressure. flushing fluid with a bri
ページ18に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. long t erm Storage When cleaning for long term storage (more than 48 hours). It is very important that the Paint Sprayer is not stored with any water or water-based material left in the Pump, Hose, Tubes, or Spray Gun. This will corrode the product. Hi Spray Low Spray Prime/Clean Roll 1. Clean the Spra
ページ19に含まれる内容の要旨
Notice Clean the Sprayer ImmedIAtely after use. delayed or inadequate cleaning will permanently clog the Spray Gun. Warranty void if sprayer is not properly cleaned immediately after every use. disposal Instructions Improper disposal of paint is against the law and a health and environmental hazard. Dispose of paint through local recycling facility. Visit www.earth911.com to find a facility near you. t roubleshooting Problem Possible Causes likely Solutions Decreased output. Obstructed trigg
ページ20に含まれる内容の要旨
Parts list Part description Qty Part description Qty 1 Spray Gun 1 55 Wire Fastening Seat 1 2 Paint Hose 1 56 Label 1 3 Base Frame 1 57 Hex Bolt (M6x10) 3 4 Hex Bolt (M6x4) 2 58 Housing 1 5 Pressure Relief Valve Label 1 59 Label 1 6 Housing Cover 1 60 Motor Assembly 1 7 Output Gear Bushing 2 61 Power Switch 1 8 Rolling Bearing 1 62 Pin (3x12) 1 9 Output Pole 1 63 Hex Bolt (M5x14) 4 10 Gear 1 64 Elastic Washer 4 11 Middle Gear Bushing 2 65 O-Ring (12.5x2.65) 2 12 Output Gear 1 66 Joint Stopper 1
