Graco Inc. 254975の取扱説明書

デバイスGraco Inc. 254975の取扱説明書

デバイス: Graco Inc. 254975
カテゴリ: 塗料噴霧器
メーカー: Graco Inc.
サイズ: 1.31 MB
追加した日付: 6/1/2014
ページ数: 18
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスGraco Inc. 254975の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Graco Inc. 254975に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Graco Inc. 254975をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Graco Inc. 254975のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Graco Inc. 254975の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Graco Inc. 254975 取扱説明書 - Online PDF
Advertisement
« Page 1 of 18 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Graco Inc. 254975を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Graco Inc. 254975の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

Operation
Interior Texture Sprayers
RTX 900 & RTX 1250
311768B
For Water-Based Materials Only
Models: 254974 & 254975
70 psi (0.49 MPa, 4.9 bar) Maximum Fluid Working Pressure
Important Safety Instructions.
Read all warnings and instructions in this
manual. Save these instructions.
Related Manuals
311777
311772
ti8867a
Model 254975 Shown
US C
Conforms to ANSI/UL
standard 1450

ページ2に含まれる内容の要旨

Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear through the man- ual, refer back to these pages for a description of the specific hazard. Warnings Fire and Explosion Hazard Improper grounding, poor ventilatio

ページ3に含まれる内容の要旨

Warnings Warnings Burn Hazard Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely. Electric Shock Hazard To reduce the risk of electric shock: � Be sure sprayer is adequately grounded through electrical outlet. � Use only 3-wire, extension cords. � Make sure ground prongs are intact on sprayer and extension cords. Improper installation of grounding plug wil

ページ4に含まれる内容の要旨

Warnings CAUTION � Water or material remaining in unit when temperatures are below freezing can damage motor and/or delay pump startup. Do not allow unit to freeze. � Before adding material or starting unit in cold weather, run warm water through pump. To ensure water and material are completely drained out of unit: ti9016a 1. Remove material line from sprayer. 2. Tip sprayer up as shown. Before adding material to the hopper, install the burp guard. When only a small amount of material rema

ページ5に含まれる内容の要旨

Component Identification Component Identification Model 254975 Shown A H U bb J cc V B S T W C K Y L D M P N R ti8939a E F G Item Component Item Component AHandle NBurp Guard BToolbox PMaterial/Air Hose C Power Cord (120V, 25 ft) Q Accessories Bag D Side Pump Access Panel (RTX 1250 Only) R Material Thickness Gauge ™ E S Nozzle RotoFlex II Pump (inside) F Pump Hose Outlet T Hose Plug G Air Hose Outlet U Touch-Up Hopper (3/4 gallon) H Material Flow Gauge V Gun Plug J Material Flow Control W Hoppe

ページ6に含まれる内容の要旨

Preparation Preparation Check with a qualified electrician or serviceman if Pressure Relief Procedure grounding instructions are not completely understood, To reduce risk of injury, follow this procedure or if in doubt as to whether the product is properly whenever you see this symbol throughout this grounded. Do not modify plug provided; if it will not fit manual, Also, perform this procedure whenever the outlet, have proper outlet installed by a qualified you: electrician. � Stop spra

ページ7に含まれる内容の要旨

Setup Setup Important � If you are going to stop spraying for more than 5 minutes, turn sprayer off to prevent shortened pump hose life. � Do not allow material to dry inside pump, hoses, gun or spray system. 4. Connect material hose to gun. Texture Spraying (material supplied from unit) ti8705a When using material 5. Make sure burp guard is installed, Caution, page 3. supplied from unit, insert the Gun Plug in the top of the gun. Hose plug must be removed from bottom of gun. ti9010a ti8

ページ8に含まれる内容の要旨

Setup 9. Turn power switch ON. Touch Up Hopper Attachment CAUTION Failure to change selector switch to Hopper Gun when using hopper gun will damage pump hose. ti9222a The Hose Plug must be 10. Close gun air valve. securely fastened to bottom of gun when using the Touch Up Hopper. Gun plug must be removed from top of gun. ti8701a ti8712a 1. Connect air hose to sprayer. 11. Point gun into waste bucket and pull trigger to pump water through the system. Continue to trigger gun 2. Connect ai

ページ9に含まれる内容の要旨

Setup 6. Turn hopper gun/spray gun selector switch to HOP- PER GUN. ti9220a 7. Open gun air valve. ti8528a 8. Turn power switch ON. ti9222a 9. To achieve uniform spray pattern, adjust air valve and flow adjustment nut on gun. If you do not achieve the desired spray pattern, change nozzles (see page 11). ti8532a 9

ページ10に含まれる内容の要旨

Mixing Material Mixing Material 5. Observe the ball on the material. When the material Correct material mixture is essential. The pump is thin enough to spray the ball will sink completely will not operate if the mixture is too thick. into the mixture. READY ADD WATER Mix the material in a separate container before pouring it into hopper. Use Material Thickness Gauge to determine mix- ture is thin enough to spray. *The Material Thickness Gauge will only deter- ti2498a mine if the material i

ページ11に含まれる内容の要旨

Spray Techniques Spray Techniques Recommended Nozzle Selection Chart To Get Less Material Try one or a combination of these methods: 2 1 Application Nozzle Size Air Volume � Open air valve. Simulated 6 mm, white medium to (fine to medium) Acoustic high � Turn gun flow adjustment nut to decrease flow, 8 mm, gray counter-clockwise. (coarse) � Use smaller nozzle. Orange peel 4 mm, beige, medium to 6 mm, white high To Get More Material Splatter 6 mm, white low to coat 8 mm, gray medium Try any o

ページ12に含まれる内容の要旨

Shutdown and Cleanup Shutdown and Cleanup Keep pump and hose clean when switching between simulated acoustic, knockdown and orange peel applications. A dirty pump can release particles of texture into the finish. CAUTION � To increase pump life, turn power off when not spraying. � Before removing material hose be sure pressure is relieved and material is not in hose. � To keep unit in good operating condition, always clean it thoroughly and prepare it properly for storage. 7. Spray inside mat

ページ13に含まれる内容の要旨

Shutdown and Cleanup Removing Material Hopper From Sprayer: 5. Turn power switch ON. The material hopper can be removed for cleaning. To remove material hopper: 1. Loosen bottom fitting. ti9222a 6. Open gun air valve. ti8871a 2. Lift material hopper straight up, off unit. ti8528a 7. Trigger gun to blow air through tip, clearing out any remaining material. 8. Remove hopper from gun and finish cleaning all components. A soft brush may be used to help loosen any dried on material from surface.

ページ14に含まれる内容の要旨

Troubleshooting Troubleshooting Problem Cause Solution Sprayer won’t run Power switch not on Turn switch on. No power at wall outlet Check outlet by plugging in another appliance. If appliance does not work, try another outlet. Wrong size generator Use a 3500 watt or larger generator. Refer to Generator Requirements, page 6. Breaker tripped Reset breaker. Pump won’t pump material Air lock Open air valve on gun. Selector switch in wrong position Move selector switch to correct posi- tion for

ページ15に含まれる内容の要旨

Troubleshooting Problem Cause Solution Speed of application slow or slower Material too thick Thin material. Nozzle too small Change nozzles to a larger size. See Recommended Nozzle Selection Chart, page 11. Too much air being used. Partially close gun air valve to reduce air flow. Pump hose worn Replace hose. Plugged or dirty gun Relieve Pressure, page 6. Clean gun. Kinked hose Unkink hose. Gun adjustment set too low Increase flow adjustment with flow adjustment nut. Too many items on sam

ページ16に含まれる内容の要旨

Technical Data Technical Data Main unit power requirements 120 Vac, 60 Hz, 15A, 1 phase Maximum fluid working pressure 70 psi, (4.9 bar) Maximum air working pressure 50 psi, (3.5 bar) Compressor specifications Universal motor thermally protected, oil-less Compressor air displacement 4.0 scfm at 45 psi Generator required 3500W minimum Electric Motor Universal AC 14 Amp 1.5 Hp Power Cord 16 AWG, 3-wire, 25 ft Material hopper capacity Model 254974: 8 gallons Model 254975: 10 gallons Gun material

ページ17に含まれる内容の要旨

Graco Warranty Graco Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applie

ページ18に含まれる内容の要旨

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. This manual contains English. MM 311768 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 Copyright 2008, Graco Inc. is registered to I.S. EN ISO 9001 www.graco.com Revised 04/2008


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Graco Inc. 1095 Premium Hi-Boy 取扱説明書 塗料噴霧器 11
2 Graco Inc. 12004 取扱説明書 塗料噴霧器 1
3 Graco Inc. 111418a 取扱説明書 塗料噴霧器 1
4 Graco Inc. 12004X 取扱説明書 塗料噴霧器 2
5 Graco Inc. 12006 取扱説明書 塗料噴霧器 2
6 Graco Inc. 12005 取扱説明書 塗料噴霧器 0
7 Graco Inc. 1095 Premium Hi 取扱説明書 塗料噴霧器 1
8 Graco Inc. 1595 HI 取扱説明書 塗料噴霧器 3
9 Graco Inc. 207-945 取扱説明書 塗料噴霧器 7
10 Graco Inc. 1595 Premium Hi 取扱説明書 塗料噴霧器 2
11 Graco Inc. 208-748 取扱説明書 塗料噴霧器 0
12 Graco Inc. 208-749 取扱説明書 塗料噴霧器 1
13 Graco Inc. 1595 Premium Hi-Boy 取扱説明書 塗料噴霧器 6
14 Graco Inc. 208-644 取扱説明書 塗料噴霧器 1
15 Graco Inc. 218-026 取扱説明書 塗料噴霧器 2
16 3M Series 52 取扱説明書 塗料噴霧器 1
17 3M Series 56 取扱説明書 塗料噴霧器 0
18 3M Series 56ZZ 取扱説明書 塗料噴霧器 1
19 3M Series 55ZZ 取扱説明書 塗料噴霧器 1
20 3M Series 57 取扱説明書 塗料噴霧器 1