Graco Inc. 254973の取扱説明書

デバイスGraco Inc. 254973の取扱説明書

デバイス: Graco Inc. 254973
カテゴリ: 塗料噴霧器
メーカー: Graco Inc.
サイズ: 1.02 MB
追加した日付: 6/1/2014
ページ数: 16
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスGraco Inc. 254973の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Graco Inc. 254973に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Graco Inc. 254973をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Graco Inc. 254973のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Graco Inc. 254973の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Graco Inc. 254973 取扱説明書 - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Graco Inc. 254973を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Graco Inc. 254973の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

Operation
Interior Texture Sprayer
RTX 650
311767B
For Water-Based Materials Only
Model 254973:
50 psi (3.5 bar) Maximum Fluid Working Pressure
100 psi (7 bar) Maximum Air Input Pressure
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Related Manuals
311777
311771
ti8370a
Model 254973 Shown
US C
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Conforms to ANSI/UL
Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001
standard 1

ページ2に含まれる内容の要旨

Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear through the manual, refer back to these pages for a description of the specific hazard. Warnings Fire and Explosion Hazard Improper grounding, poor ventilation

ページ3に含まれる内容の要旨

Warnings Warnings Electric Shock Hazard To reduce the risk of electric shock: � Be sure sprayer is adequately grounded through electrical outlet. � Use only 3-wire, extension cords. � Make sure ground prongs are intact on sprayer and extension cords. Improper installation of grounding plug will result in a risk of electrical shock, fire or explosion that could cause serious injury or death. � Do not operate with cover removed. � Turn off sprayer. Follow Pressure Relief Procedure, page 6, and

ページ4に含まれる内容の要旨

Warnings CAUTION Water or material remaining in unit when temperatures are below freezing can damage motor and/or delay pump startup. To insure water and material are completely drained out of unit: 1. Remove material line from sprayer. 2. Tip sprayer up as shown. ti9075a Before adding material or starting unit in cold weather, run warm water through pump. Before adding material to hopper, install burp guard (J). When only a small amount of material remains in the hopper, the burp guard preve

ページ5に含まれる内容の要旨

Component Identification Component Identification A P B N M C H D R ti8369a E L F G J K Q 3.5 cfm@40 min. Item Component Item Component A Pump Hose Outlet J Burp Guard B RotoFlex™ II Pump (inside) K ON/OFF Switch C Texture Spray Gun (Manual 311777) L Power Cord (120V, 15 ft) D Nozzle (2 included, see Nozzle Selection, page 10) M Material Hopper - 5 gallon E Material Hose (20 ft) N Cord Wrap F Material Thickness Gauge P Handle G Accessories Bag Q Air Compressor (Not Supplied by Graco) H Gun Air V

ページ6に含まれる内容の要旨

Preparation Preparation Check with a qualified electrician or serviceman if Pressure Relief Procedure grounding instructions are not completely understood, To reduce risk of injury, follow this procedure or if in doubt as to whether the product is properly whenever you see this symbol throughout this grounded. Do not modify plug provided; if it will not fit manual, Also, perform this procedure whenever the outlet, have proper outlet installed by a qualified you: electrician. � Stop spra

ページ7に含まれる内容の要旨

Setup Setup Important � To increase pump life, turn power off when not spraying. � Do not allow material to dry inside pump, hoses, gun or spray system. � To break in new pump run dry for no more than 2 minutes. 4. Connect material hose to gun. Texture Spraying 1. Connect air hose to user-supplied air compressor & material hose (G) to material hose outlets. ti8705a 5. Install spray nozzle. See Recommended Nozzle Selection Chart, page 10. ti8375a 2. Connect user supplied air hose to gun. ti977

ページ8に含まれる内容の要旨

Setup 11. Continue to trigger gun and spray into waste bucket until a steady stream of material sprays out of gun. 12. Turn on Air compressor and open gun valve to desired setting. ti9202a 8. Point gun into waste bucket and pull trigger to pump water through the system. Continue to trigger gun until material hopper is empty. 9. Install burp guard (J). Caution, page 3. ti9775a 13. To achieve uniform spray pattern, adjust air valve and flow adjustment nut on gun. If you can not achieve a

ページ9に含まれる内容の要旨

Mixing Material Mixing Material 4. After texture material is thoroughly mixed, gently set Correct material mixture is essential. The pump ball end of Material Thickness Gauge on surface of will not operate if the mixture is too thick. mixture. Mix the material in a separate container before For an accurate test, be sure gauge is completely pouring it into hopper. dry and clean every time it is used. Use Material Thickness Gauge to determine 5. Observe the ball on the material. When the mat

ページ10に含まれる内容の要旨

Spray Techniques Spray Techniques Recommended Nozzle Selection Chart To Get Less Material Try one or a combination of these methods: 2 1 Application Nozzle Size Air Volume � Open air valve. Simulated 6 mm, white (fine to medium) medium to Acoustic 8 mm, gray (coarse) high � Turn gun flow adjustment nut to decrease flow, medium to counter-clockwise. Orange peel 6 mm, white high � Use smaller nozzle. Splatter 6 mm, white low to coat 8 mm, gray medium To Get More Material Knockdown 8 mm, gray

ページ11に含まれる内容の要旨

Shutdown and Cleanup Shutdown and Cleanup Keep pump and hose clean when switching between simulated acoustic, knockdown and orange peel applications. A dirty pump can release particles of texture into the finish. CAUTION � To increase pump life, turn power off when not spraying. � Before removing material hose be sure pressure is relieved and material is not in hose. � To keep unit in good operating condition, always clean it thoroughly and prepare it properly for storage. 5. Spray inside mate

ページ12に含まれる内容の要旨

Troubleshooting Troubleshooting Problem Cause Solution Sprayer won’t run Power switch not on Turn switch on. No power at wall outlet Check outlet by plugging in another appliance. If appliance does not work, try another outlet. Wrong size generator Use a 3500 watt or larger generator. Refer to Generator Requirements, page 6. Breaker tripped Reset breaker. Pump won’t pump material Air lock Open air valve on gun. Mix too thick Add water to thin material. Use Mate- rial Thickness Gauge. Loose

ページ13に含まれる内容の要旨

Troubleshooting Problem Cause Solution Speed of application slow or slower New pump hose not broken in Run pump dry for no more than 2 properly minutes. Material too thick Thin material. Nozzle too small Change nozzles to a larger size. See Recommended Nozzle Selection Chart, page 10. Too much air being used Partially close gun air valve to reduce air flow. Pump hose worn Replace hose. Plugged or dirty gun Relieve Pressure, page 6. Clean gun. Kinked hose Unkink hose. Gun adjustment set too

ページ14に含まれる内容の要旨

Technical Data Technical Data Main Unit Power Requirements . . . . . . . . . . . . . . . . . . . . 120 Vac, 60 Hz, 15A, 1 phase Maximum Fluid Working Pressure . . . . . . . . . . . . . . . . . . 50 psi, (3.5 bar) Maximum Air Working Pressure. . . . . . . . . . . . . . . . . . . . 100 psi (7.0 bar) Compressor Specifications . . . . . . . . . . . . . . . . . . . . . . . Universal motor thermally protected, oil-less Compressor (Not Supplied) . . . . . . . . . . . . . . . . . . . . . . . 3.5 @ 40 p

ページ15に含まれる内容の要旨

Notes Notes 15

ページ16に含まれる内容の要旨

Graco Warranty Graco Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty appli


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Graco Inc. 1095 Premium Hi-Boy 取扱説明書 塗料噴霧器 11
2 Graco Inc. 12004 取扱説明書 塗料噴霧器 1
3 Graco Inc. 111418a 取扱説明書 塗料噴霧器 1
4 Graco Inc. 12004X 取扱説明書 塗料噴霧器 2
5 Graco Inc. 12006 取扱説明書 塗料噴霧器 2
6 Graco Inc. 12005 取扱説明書 塗料噴霧器 0
7 Graco Inc. 1095 Premium Hi 取扱説明書 塗料噴霧器 1
8 Graco Inc. 1595 HI 取扱説明書 塗料噴霧器 3
9 Graco Inc. 207-945 取扱説明書 塗料噴霧器 7
10 Graco Inc. 1595 Premium Hi 取扱説明書 塗料噴霧器 2
11 Graco Inc. 208-748 取扱説明書 塗料噴霧器 0
12 Graco Inc. 208-749 取扱説明書 塗料噴霧器 1
13 Graco Inc. 1595 Premium Hi-Boy 取扱説明書 塗料噴霧器 6
14 Graco Inc. 208-644 取扱説明書 塗料噴霧器 1
15 Graco Inc. 218-026 取扱説明書 塗料噴霧器 2
16 3M Series 52 取扱説明書 塗料噴霧器 1
17 3M Series 56 取扱説明書 塗料噴霧器 0
18 3M Series 56ZZ 取扱説明書 塗料噴霧器 1
19 3M Series 55ZZ 取扱説明書 塗料噴霧器 1
20 3M Series 57 取扱説明書 塗料噴霧器 1