Kenmore 153.326662 50 GALの取扱説明書

デバイスKenmore 153.326662 50 GALの取扱説明書

デバイス: Kenmore 153.326662 50 GAL
カテゴリ: 給湯器
メーカー: Kenmore
サイズ: 4.59 MB
追加した日付: 12/25/2013
ページ数: 32
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスKenmore 153.326662 50 GALの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Kenmore 153.326662 50 GALに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Kenmore 153.326662 50 GALをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Kenmore 153.326662 50 GALのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Kenmore 153.326662 50 GALの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Kenmore 153.326662 50 GAL 取扱説明書 - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Kenmore 153.326662 50 GALを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Kenmore 153.326662 50 GALの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

Owner's Manual
®
POWER MISERTM 6
ELECTRIC
WATER HEATER
FOR POTABLE WATER HEATING ONLY.
NOT SUITABLE FOR SPACE HEATING.
MODEL NO.
153.326362 30 Gal.
153.326363 30 Gal.
153.326462 40 Ga!.
153.326463 40 Gal.
153.326562 55 Gal.
153.326563 55 Gal.
153.326662 50 GaL Medium
153.326663 50 Gal. Medium
153.326762 40 Gal. Medium
153.326763 40 Gal, Medium
153,326862 50 Gal, Short
......... ; ;;;;_i;:_ii:;:;i:_ii!iiiiii!i_!iiiiiii!iiii!i!ili!!iiii!iiii ¸iiii!iii!i;iiiiiiil ¸iiiiiiiiiiiii!!!;i_iii;iiiiiiiiiii

ページ2に含まれる内容の要旨

Your safety andthesafety ofothers is extremely important in the installation, use and servicing of this water heater. Many safety=related messages and instructions have been provided in this manual and on your own water heater to warn you and others of a potential injury hazard. Read and obey all safety messages and instructions throughout this manual. It is very important that the meaning of each safety message is understood by you and others who install, use or service this water heater. to po

ページ3に含まれる内容の要旨

Read andunderstand instruction improper installation and use may result manual and safety messages in property damage. before installing, operating or servicing thiswater heater. - Do not operate water heater if flood damaged. - Inspect and replace the anode as needed. Failure tofollow instructions and - Install in location with drainage. safety messages could result in - Fill tank with water before operation. death orserious injury. - Be alert for thermal expansion. Instruction manual must rema

ページ4に含まれる内容の要旨

"q! SAFE INSTALLATION, USEAND SERVICE ........................................................................................................................................ 2 GENERAL SAFETY ............................................................................................................................................................................. 3 TABLE OF CONTENTS ..................................................................................................................

ページ5に含まれる内容の要旨

The installation must conform with the instructions in this ThankYouforpurchasing a Sears waterheater. Properly manual; electric company rules; and Local Codes, or in the installed andmaintained, it should giveyouyears oftrouble absence of Local Codes, with the current edition of the freeservice. Itisstrongly suggested thatthisnew water heater beprofessionally installed, contact thelocalSearsService NEC - National Electrical Code, NFPA 70. This publication is available from your local government

ページ6に含まれる内容の要旨

Materials Needed To simplify the installation Sears has available the installation parts shown below. You may or may not need all of these materials, depending on your type of installation. DRAIN PANS AVAILABLE IN 20" EXPANSION TANKS FOR THERMAL EXPANSION CONDITIONS AVAILABLE IN 2 DIAMETER FORWATER HEATERS HAVING A DIAMETER 18" OR LESS, GALLONS , AND 5 GALLONS CAPACITY THROUGH LOCAL SEARS STORE OR 24" DIAMETER FOR WATER SERVICE CENTER. HEATERS HAVING A DIAMETER 22" WATER HEATER INSTALLATION KIT

ページ7に含まれる内容の要旨

The water passing out of the drain valve may be extremely hot. Removing the Old Water Heater To avoid being scalded, make sure all connections are tight and that the water flow is directed away from any person. 4. Check again to make sure the electrical supply is turned "OFF" to the water heater. Then unplug the water heater (cord set) or disconnect the electrical supply connection from the water heater junction box. FIGURE 4. 5a. If you have copper piping to the water heater, the two copper wat

ページ8に含まれる内容の要旨

• Sensors mounted in the drain pan that turn offthe water supply to the entire home when water is detected in the drain pan. • Water supply shut-off devices that activate based on the water Mineral Buildup or Sediment IVlayAccumalate pressure differential between the cold water and hot water pipes connected to the water heater. . This causes the water heater to become much heavier than normal. ® If spilled, could cause staining. Installations in Residential Garages Mineral buildup or sediment ma

ページ9に含まれる内容の要旨

HOTTER WATER CAN SCALD: Water heaters are intended to produce hot water. Water heated to a temperature which will satisfy clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Fire Hazard / Electric Shock Hazard Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, the infirm, or physically/mentally handicapped. If anyone using hot water - Do not use this water heater with in you

ページ10に含まれる内容の要旨

Fit T & P valve insulation over valve. Make sure that the insulation NOTE: Toprotect against untimely corrosion ofhot and cold does not interfere with the lever of the T & P valve. water fittings, it is strongly recommended that di=electric unions or couplings be installed on this water heater when Secure all insulation using tape. connected to copper pipe. 1. Look at the top cover of the water heater. The hot water outlet is marked hot. Put two or three turns of teflon tape around the threaded

ページ11に含まれる内容の要旨

Position thevalvedownward andprovide tubing sothatany Ifaftermanually operating thevalve, itfailstocompletely reset discharge willexitonlywithin 6inches (153mm)above, orat andcontinues to release water, immediately closethecold any distance below thestructural floor. Becertain thatnocontact water inlet tothewater heater, follow thedraining instructions, ismade withanyliveelectrical part.Thedischarge opening andreplace thetemperature-pressure reliefvalve witha new one. must not be blockedor reduc

ページ12に含まれる内容の要旨

Necessary element conversion parts are located in a small Converting the Lower Element bag contained within the electrical junction box on top of the water heater. These instructions only cover the conversion of the convertible element, read this entire manual before attempting to install or operate the water heater. The water heater is factory set to CONVERSION PARTS operate at 3800 watts. The lower element can be converted to operate at 5500 watts. Refer to "Facts to Consider About the Convert

ページ13に含まれる内容の要旨

8. Tighten terminals 2 and3 to ensure proper electrical LIFT OUT TABTO UNCLIPTERMINAL connection. JACK_ _-, COVER FROM PLASTIC TABSON THERMOSTAT TERMINAL COVER t BOTH SIDES OF TERMINAL COVER CLIPPED TO _ THERMOSTAT AT HOL IT IN PLACE THIS POINT _ tHERMOSTAT BRACKET Fire and E×plosion Hazard _-TANK • Failure to tighten screws can _'_ " ELEMENT cause a fire. THERMOSTAT • Failure to do this could result in death, serious bodily injury, or property damage. FIGURE 16. Failure to tighten terminal scre

ページ14に含まれる内容の要旨

11.Replace theaccess panel. Fire Hazard / Electric Shock Hazard ® Do not use this water heater with any voltage other than shown on the model rating plate. Failure to use the correct voltage shown on the model rating plate FIGURE 21. could result in death, serious bodily injury, or property damage. 12. Complete wiring to the water heater, or if completed, turn "ON" electric power to the water heater after filling the tank with water. If wiring from your fuse box or circuit breaker box was alumin

ページ15に含まれる内容の要旨

5. Wiring Diagrams (see "Wiring Diagrams" section) have been 6. Use wire nuts and connect the power supply wiring to the supplied showing the two most common types of wires inside the water heater's junction box. connections between the water heater and the power supply. You can easily see which type connection you have by 7. The water heater must be electrically "grounded" by the removing the junction box cover on top of the water heater. installer. A green ground screw has been provided on the

ページ16に含まれる内容の要旨

Wiring Diagrams STANDARD WiriNG FOR 2 WiRE LEAD WATER HEATERS NON=SIMULTANEOUS OPERATION 240 VOLT DOUBLE ELEMENT A6 [ GROUNDTERMINAL--""""-_,_ * Before removing any access panels or servicing the water _1 _*,_l L_ POWER SUPPLY heater, make sure the electrical supply to the water heater is H,-TEMP _ JUNJTiON turned "OFF". LIMIT_l O_1I_(bl BOX sw,TCB _40-11_ tt" , Failure to do this could result in death, serious bodily injury, or TH2tggPTAT --n property damage. J I_ _f% ELEMENT <, THERMOS FOR 550

ページ17に含まれる内容の要旨

The lower thermostat is factory set at a position which Temperature Regulation approximates 120°F (49°C), and is adjustable if a different water temperature is desired. Read all warnings in this manual and on the water heating before proceeding. Water temperature over 125°F (52°C) can cause severe burns TEMPERATURE instantly resulting in severe injury ADJUSTMENT or death. KNOB Children, the elderly, and the physically or mentally disabled are at highest risk for scald injury. Feel water before b

ページ18に含まれる内容の要旨

Theupper andlower thermostats areadjustable ifa different Temperature-Pressure Relief Valve Operation watertemperature is desired.Readall warningsin the "Temperature-Regulation" section before proceeding. The temperature-pressure relief valve must be manually operated at least once a year. 1. Turn "OFF" the electric power to the water heater at the junction box. • Burn hazard [ • Hotwater discharge. Before removing any access • Keep clear of relief valve panels or servicing the water discharge o

ページ19に含まれる内容の要旨

Thewater heater should bedrained ifbeing shutdown during 1. Turn "OFF" the electrical power to the water heater at the freezing temperatures. Also,periodic draining andcleaning of junction box. sediment fromthetankmaybenecessary. 2. Remove the access panel and the insulation cap with handle. l 3. Lift out the tab as shown below to unclip the terminal cover • Before removing any access from the thermostat. The terminal cover can now be removed panels or servicing the water from the thermostat. he

ページ20に含まれる内容の要旨

Remove the two screws securing the access panel, and remove panel. [ o Before removing any access panels or servicing the water heater, make sure the electrical supply to the water heater is turned "OFF". • Failure to do this could result in death, serious bodily injury, or property damage. FIGURE 33. Before beginning turn "OFF" the electric power supply to the water heater. 5. Remove the insulation cap with handle. QI .___J FIGURE 30. 2. Turn off the water supply to the water heater at the wate


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Kenmore 153 327566 50 GAE 取扱説明書 給湯器 1
2 Kenmore 153.32118 取扱説明書 給湯器 0
3 Kenmore 153.326462 40 GA!. 取扱説明書 給湯器 1
4 Kenmore 153.326363 30 GAL. 取扱説明書 給湯器 0
5 Kenmore 153.326362 30 GAL. 取扱説明書 給湯器 0
6 Kenmore 153.326463 40 GAL. 取扱説明書 給湯器 1
7 Kenmore 153.326562 55 GAL. 取扱説明書 給湯器 0
8 Kenmore 153.31702 取扱説明書 給湯器 1
9 Kenmore 153.326563 55 GAL. 取扱説明書 給湯器 2
10 Kenmore 153.32116 取扱説明書 給湯器 0
11 Kenmore 153.326762 40 GAL. 取扱説明書 給湯器 0
12 Kenmore 153.326663 50 GAL. 取扱説明書 給湯器 1
13 Kenmore 153.326763 40 GAL 取扱説明書 給湯器 0
14 Kenmore 153.327565 50 GAL 取扱説明書 給湯器 0
15 Kenmore 153.327366 取扱説明書 給湯器 0
16 A.O. Smith 000 取扱説明書 給湯器 8
17 A.O. Smith 101 取扱説明書 給湯器 3
18 A.O. Smith 12 40GPC T 100 取扱説明書 給湯器 4
19 A.O. Smith 104 Series 取扱説明書 給湯器 3
20 A.O. Smith 104 - 110 取扱説明書 給湯器 6