ページ1に含まれる内容の要旨
ELECTRIC FIREPLACE/INSERT
SAFETY INFORMATION AND INSTALLATION MANUAL
For Model CEF26BN with Brushed Nickel Trim
Read these instructions completely before beginning
installation. Failure to follow them could cause a heater
malfunction resulting in serious injury and/or property
damage.
WARNING: All electric heaters have hot and arcing or
sparking parts inside. Do not use it in areas where gaso-
line, paint or flammable liquids are or are stored.
WARNING: This heater is tested and listed for us
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Safety Information ............................................... 2 Operating Instructions ......................................... 7 Listing Approvals ................................................. 3 Cleaning and Maintenance .................................. 9 Product Dimension Specifications ....................... 3 Technical Service .............................................. 10 Unpacking and Testing Fireplace ........................ 4 Replacement Parts ...........
ページ3に含まれる内容の要旨
SAFETY INFORMATION PRODUCT DIMENSION Continued SPECIFICATIONS 10. To prevent possible fire, do not block air intakes in any manner. 26.125 11. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. 12. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. 13. Avoid the use of an extension cord because the ex
ページ4に含まれる内容の要旨
UNPACKING AND WARNING: To prevent TESTING FIREPLACE contact with sagging or loose Carefully remove the unit from the box. Prior insulation, the heater must not to permanently installing the unit, test to make be installed against vapor barrier sure the unit operates properly. To do this, plug or exposed insulation. Localized the unit's power supply cord into a conveniently located 120-volt grounded outlet. overheating could occur and a fire could result. CAUTION; The unit's power su
ページ5に含まれる内容の要旨
LOCATING FIREPLACE INSTALLATION Continued WARNING - RISK OF FIRE! The power cord must not be CAUTION: Provide adequate pinched or against a sharp edge. clearances around the air open- Secure cord to avoid tripping or ings and adequate accessibility snagging to reduce the risk of fire, clearances for servicing and electric shock or personal injury. proper operations. Do not run cord under carpet- ing. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic
ページ6に含まれる内容の要旨
INSTALLATION New Construction or Renovation Continued 1. Select a location that is not prone to moisture and is located at least .9 m or 3 feet away INSTALLING AS A FIREPLACE from combustible materials such as curtains or drapes, furniture, bedding, paper, etc. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and 2. Place unit in selected location to see how it high traffic areas. Note: Follow all national and will look in the future. local
ページ7に含まれる内容の要旨
FINISHING IMPORTANT: Once you turn the Combustible Finishing Material : Materials main switch to the ON posi- made of or surfaced with wood, compressed paper, tion, the remote control can no plant fibers, plastics or any material capable of longer be used. In order to use igniting and burning, whether flame proofed or not, plastered or unplastered (this includes drywall). the remote control, you must Noncombustible Finishing Material : Mate- keep the main ON/OFF switch rials which will n
ページ8に含まれる内容の要旨
To increase the flame intensity, press OPERATING and release the HIGHER button. Each INSTRUCTIONS time you press the button you will hear a Continued beep and the size of the flame will increase slightly until the maximum setting is IMPORTANT: To control the reached. electric fireplace by remote, the To decrease the flame intensity, press Main ON/OFF power switch on and release the LOWER button. Each time the fireplace must be in the OFF you press this button you will hear a beep and t
ページ9に含まれる内容の要旨
2. To remove fingerprints or other marks, the OPERATING glass can be cleaned with a damp cloth using INSTRUCTIONS a good quality household glass cleaner. The Continued glass should be completely dried with a lint 8. To turn off the fireplace, press the POWER free cloth or paper towel. ON/OFF button once. When you hear the 3. In the event of glass breakage, vacuum all beep, the fireplace will be completely off remaining glass pieces with a shop vac. DO and the flame will disappear. When you
ページ10に含まれる内容の要旨
9. Repeat steps 5 and 6 for second bulb. CLEANING AND 10. Insert bottom edge of removed cylinder half MAINTENANCE into bottom drum track. Squeeze drum cylin- Continued der until it's top edge fits into top drum rack. 4. Hold socket and push in new bulb (DO NOT 11. With gloves, carefully replace glass. Slide top exceed wattage). of glass into metal slot and slide bottom onto 5. Replace spring clip onto bulb. ledge. 6. Repeat steps 3 through 5 for second bulb. 12. Place brackets against glass
ページ11に含まれる内容の要旨
PARTS NOT UNDER WARRANTY REPLACEMENT PARTS Contact authorized dealers of this product. If they Note: Use only original replacement parts. This canʼt supply original replacement part(s), call will protect your warranty coverage for parts DESA Heating Products at 1-866-672-6040 for replaced under warranty. referral information. PARTS UNDER WARRANTY When calling DESA Heating Products, have Contact authorized dealers of this product. If ready they canʼt supply original replacement part(s),
ページ12に含まれる内容の要旨
WARRANTY INFORMATION KEEP THIS WARRANTY Model Serial No. Date Purchased Always specify model and serial numbers when communicating with the factory. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied. LIMITED WARRANTY ELECTRIC FIREPLACE/INSERT DESA Heating Products warrants this product to be free from defects in materials and components for one (1) year fr
