ページ1に含まれる内容の要旨
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Model:
MTL-Insert
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating • Read, understand and follow
• Leave this manual with
and maintenance these instructions for safe party responsible for use
instructions included. installation and operation. and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fi re HOT SURFACES!
Glass and other surfaces are hot during
or explosion may result cau
ページ2に含まれる内容の要旨
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Heat & Glo gas appliance This Owner’s Manual should be retained for future —an elegant and clean alternative to wood burning reference. We suggest that you keep it with your other important documents and product manuals. appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, The
ページ3に含まれる内容の要旨
Table of Contents 1 Listing and Code Approvals 8 Gas Information A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 B. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 C. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. Ga
ページ4に含まれる内容の要旨
Listing and Code Approvals 1 1 A. Appliance Certifi cation C. High Altitude Installations U.L. Listed gas appliances are tested and approved with- MODELS: MTL-INSERT out requiring changes for elevations from 0 to 2000 feet LABORATORY: Underwriters Laboratories, Inc. (UL) in the U.S.A. and Canada. TYPE: Vented Gas Fireplace Heaters When installing this appliance at an elevation above STANDARD: ANSI Z21.88a-2007/CSA 2.33a-2007 2000 feet, it may be necessary to decrease the input rat- ing by
ページ5に含まれる内容の要旨
Getting Started 2 2 A. Design and Installation Considerations C. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of WARNING the building and all exhaust gases expelled to the outside. Inspect appliance and components for damage. No additional outside air source is required. Damaged parts may impair safe operation. • Do NOT install damaged components. CAUTION • Do NOT install incomplete components
ページ6に含まれる内容の要旨
Fireplace Size Requirements 3 3 • The metal fl oor of the solid fuel fi rebox may be removed to A. Minimum Fireplace Opening facilitate the installation of the insert. The appliance may Minimum fi replace opening requirements are shown in not be placed directly on the base of the outer wrap, a 1/4 Figure 5.1. inch airspace must be provided between the insert and WARNING! Risk of Fire or Burns! Provide adequate the fl oor of the outer wrap. Use the levelling legs to raise clearance arou
ページ7に含まれる内容の要旨
B. Clearances WARNING Fire Risk. Odor Risk. • Clearance to combustible material under the insert is 1/4 inch (0.6 cm). • Use leveling legs to raise insert minimum 1/4 inch above combustible material or outer wrap of factory built fi rebox. WARNING Fire Risk. • Locate and install appliance to all clearance specifi cations in manual. INLET AIR 12 in. MAX. EXHAUST VENT PIPE VENT PIPE MANTEL 15 in. MIN. MEASUREMENTS FROM TOP EDGE OF UNIT Figure 3.2 Clearances to Mantels or other Combustibles abov
ページ8に含まれる内容の要旨
Termination Locations 4 4 A. Vent Termination Minimum Clearances Figure 4.1 specifi es minimum vent heights for various pitched roofs. HORIZONTAL OVERHANG 2 FT. 20 INCHES MIN. VERTICAL MIN. WALL LOWEST DISCHARGE OPENING GAS DIRECT VENT TERMINATION CAP X 12 ROOF PITCH IS X/ 12 H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 ...................................
ページ9に含まれる内容の要旨
Vent Information and Diagrams 5 5 A. Vent Table Key WARNING The abbreviations listed in this vent table key are used in the vent diagrams. Fire Hazard. Explosion Risk. Symbol Description Asphyxiation Risk. V Minimum Vertical Run Length 14 ft. Do NOT connect this gas appliance to a MIN chimney fl ue serving a separate solid fuel or V Maximum Vertical Run Length 50 ft. MAX gas burning appliance. • May impair safe operation of this appliance B. Horizontal Venting or other appliances connecte
ページ10に含まれる内容の要旨
Installation Preparation 6 6 Prepare the existing solid fuel masonry or factory built E. Fireplace Conversion Notice non-combustible fi rebox for installation. Permanently attach the label with the following warning to the inside lower back of the fi replace fi rebox into which A. Flue Damper the insert is being installed. Silicone may be required to Fully lock the solid fuel fi replace’s fl ue damper in the open properly secure the label. position, OR completely remove it. B. Chimney WARNIN
ページ11に含まれる内容の要旨
Installing Vent Pipe and Appliance 7 7 A. Venting Components B. Connecting Vent Pipe Reference instructions in the termination kit. CAUTION • Install the 3-inch fl exible vent pipe(s) down through the chimney. Sharp Edges • Use three screws to secure the exhaust fl exible vent • Wear protective gloves and safety pipe to the 3 foot section stainless steel fl exible vent pipe glasses during installation. using the factory-installed 3-inch collar in the stainless steel section of pipe (see Fi
ページ12に含まれる内容の要旨
CUT AND BEND WARNING FLASHING AS NEEDED TO FIT CHIMNEY Fire Risk. Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fi replaces. • No other components such as shrouds, sheet- SEALANT metal plates, etc., may be used to seal off vents. ADHESIVE WARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifi cally approved with this appliance may result in property damage or personal injury
ページ13に含まれる内容の要旨
D. Installing Termination Cap CAUTION For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.3) . Sharp Edges • Wear protective gloves and safety glasses during installation. HORIZONTAL OVERHANG Damper Flashing Kit (Optional) For use with LINK-DV4-30B Liner Kit. 2 FT. 20 INCHES MIN. VERTICAL MIN. WALL Note: Damper may have to be removed to use this kit. LOWEST DISCHARGE OPENING • Run fl ex liners through 3” holes in damper fl ashing. GAS DIRECT VENT
ページ14に含まれる内容の要旨
Gas Information 8 8 A. Fuel Conversions C. Gas Connection Before making gas connections ensure that appliance be- Note: Have the gas supply line installed in accordance ing installed is compatible with the available gas type. with local building codes, if any. If not, follow ANSI Any natural or propane gas conversions necessary to 223.1. Installation should be done by a qualifi ed installer meet the appliance and locality needs must be made by approved and/or licensed as required by th
ページ15に含まれる内容の要旨
HIGH ALTITUDE INSTALLATIONS WARNING U.L. Listed gas appliances are tested and approved without Fire or Explosion Hazard requiring changes for elevations from 0 to 2000 feet in the • Gas buildup during line purge may ignite. U.S.A. and Canada. • Purge should be performed by qualifi ed technician. When installing this appliance at an elevation above 2000 feet, • Ensure adequate ventilation. it may be necessary to decrease the input rating by changing • Ensure there are no ignition sources such
ページ16に含まれる内容の要旨
Electrical Information 9 9 Appliance Requirements A. Wiring the Appliance • This appliance DOES NOT require 110-120 VAC to Note: Electrical wiring must be installed by a licensed operate. electrician. • It is recommended that a 110 VAC junction box be connected for use with fan or remote control. (See Figure 9.2 for junction box wiring). Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric
ページ17に含まれる内容の要旨
B. Optional Junction Box Installation JUNCTION BOX ACCESS SIDEWALL JUNCTION BOX SCREW PROVIDED Figure 9.2 Optional Junction box installation Note: The MTL-INSERT does not ship standard with a junction box. The junction box is an op- tional accessory. Optional Accessories Connecting the electrical junction box is required if using a blower or remote. • Plug the cord into a convenient outlet. • An electrician may install an outlet box inside the fi replace. Place the outlet in the lower, back
ページ18に含まれる内容の要旨
VARIABLE SPEED CONTROL JUNCTION BOX BLK BLK BLOWER RECEPTACLE BLK BLK BLK BLK BLK WHT WHT BLK GROUND BLOWER TEMPERATURE GRN SENSOR SWITCH BLK WHT 110-120 VAC FAN JUNCTION BOX TEMPERATURE SENSOR SWITCH SPEED CONTROL (RHEOSTAT) BEND GROUND WIRE UP TABS (ATTACH TO ANY METAL SURFACE) Figure 9.3 Fan/Rheostat Wire Diagram (Optional) Note: The MTL-INSERT does not ship standard with a fan. The fan is an optional accessory. 18 Heat & Glo • MTL-Insert • 2145-900 Rev. F • 9/08
ページ19に含まれる内容の要旨
Finishing 10 10 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. INLET AIR 12 in. MAX. EXHAUST VENT PIPE VENT PIPE MANTEL 15 in. MIN. MEASUREMENTS FROM TOP EDGE OF UNIT Figure 10.1 Clearances to Mantels or other Combustibles above Appliance Heat & Glo • MTL-Insert • 2145-900 Rev. F • 9/08 19
ページ20に含まれる内容の要旨
Appliance Setup 1 11 1 A. Remove Shipping Materials Placing the Ember Material Ember material is shipped with this gas appliance. To place Remove shipping materials from inside or underneath the the ember material: fi rebox. • Embers CANNOT be placed directly over ports. B. Clean the Appliance • When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place Clean/vacuum any sawdust that may have accumulated the dime-size ember pieces near port
