ページ1に含まれる内容の要旨
©2009 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, S San an Ant Antonio, onio, T TX X 78 782 21 19. 9.
Printed in China. Issue 3 AT&T 09/09
User’s manual
Part 2
SB67128 DECT 6.0
Repeater
This manual contains information about
this product’s installation and operation.
Please also read Part 1 - Important
product information.
For customer service or product
information, visit our
ページ2に含まれる内容の要旨
Before you install Parts list • B6 � ��2� DECT 6.0 repeater • Power adapter • Part � Important product information • Part 2 User’s manual • Package of screws Use only the power adapter supplied with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1 (888) 915-2007. In Canada, dial 1 (866) 288-4268. Figure � : Repeater �
ページ3に含まれる内容の要旨
About the repeater You can use a repeater to extend the operating range for the AT&T �B6 ���� DECT 6.0 4-line corded/cordless telephone system to cover areas where the signal is very weak or not available. The repeater extends the range in all directions, even going around certain barriers. The telephone base, cordless handsets and repeaters are linked through wireless connections. When configured properly, you should not notice any reception problems as you move around within the covered
ページ4に含まれる内容の要旨
Registration You should register your repeaters to the telephone base before choosing locations for them in the building. NOTE: You can register a repeater to an �B6���� telephone base without deregistering it from a previous telephone base. New registrations overwrite any previous repeater registrations. Repeater registration �. Plug in the repeater to AC power. The STATUS indicator light on the repeater flashes slowly. 2. Press and hold the SETUP button at the bottom of the repeater for
ページ5に含まれる内容の要旨
Registration STATUS indicator light Slow flash The repeater is powered on and in idle mode waiting to be re- registered. -OR- The registered repeater is not connected to the telephone base. -OR- Your telephone base has no power. Quick flash The repeater is registering to the telephone base. On The repeater is successfully registered and in a normal operation mode. Off The repeater has no power. 4
ページ6に含まれる内容の要旨
Installation After you have plugged in your repeaters in the locations you think are best, place a call from a cordless handset (AT&T B6 � ��0�) and while talking, move around the building to test the reception. You may want to adjust the position of repeaters to receive the best reception. Plug the small end of the power adapter into the power jack on the front of the repeater and route the cord through the slot on the bottom of the repeater. Route the power adapter cord through the slo
ページ7に含まれる内容の要旨
Installation You can place the repeater on a tabletop. You can install your repeater on a wall or other object with the provided screws. Please use the recommended placement and installation tips as follows: • The antennas needs to be in a high location (not on the floor or under a desk) for reception. • Maintain a minimum of 30 feet distance between each repeater. • �ee page 2 for additional placement information. If you place the repeater on a tabletop, plug the large end of the power a
ページ8に含まれる内容の要旨
Installation If you want to install your repeater on a wall or other object, use the provided screws. Professional assistance may be required to install screws on the wall. Then plug the large end of the power adapter into a nearby electrical wall outlet and raise the antennas. ^ � crew holes � crew spacing=2.5 inches Figure 5: Wall installation NOTE: The The power power adapt adapter er is is int intended ended t to o be be c corr orrectl ectly y orient oriented ed in in a a v vertical ert
ページ9に含まれる内容の要旨
Troubleshooting If you have difficulty operating this repeater, try the suggestions below. To contact Customer �ervice, purchase accessories or obtain replacement parts, visit our website at www.telephones.att.com or call 1 (888) 915-2007. In Canada, dial 1 (866) 288-4268. Please retain your receipt as your proof of purchase. My repeater • Make sure the power cord is securely plugged in. doesn’t work • Make sure the STATUS indicator light is on. If at all. the light is off or flashing, th
ページ10に含まれる内容の要旨
Troubleshooting • First try all the suggestions on the previous My repeater page. cannot register to my telephone • Make sure your telephone base is model AT&T base. �B6���� DECT 6.0 4-line corded/cordless telephone system. • Carefully follow the registration instructions on pages 3 of this user’s manual. • Make sure your telephone base is within 950 feet of the repeater. If registration does not work, place the repeater next to the base and try registering again. My repeater • Fi
ページ11に含まれる内容の要旨
General product care To keep the repeater working and looking good, follow these guidelines: • Avoid putting it near appliances and devices that generate electrical noise (motors, fluorescent lights, etc.) • DO NOT expose it to direct sunlight or moisture. • Avoid dropping the repeater. • Clean with a soft cloth. • Never use a strong cleaning agent or abrasive powder because this will damage the finish. • Retain the original packaging in case it is necessary to ship it at a later date. �0
ページ12に含まれる内容の要旨
Technical specifications RF frequency band 92 � .536 MHz — � 92 � .44 � MHz � Channels 5 Operating temperature 32°F — 22°F � 0°C — 50°C Repeater voltage ��0 — 20 V � rms (AC voltage, 60Hz) Repeater voltage 6VDC @600mA (AC adapter output) Repeater operating range This repeater operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this product can communicate over only a certain distance — which can vary with the locations of the telephone base, the
