ページ1に含まれる内容の要旨
OWNER'S
MANUAL
MODEL NO.
580.751500
_®
5 HORSEPOWER
1800 PS! 2.5 GPM
HiGH PRESSURE WASHER
o Assembly
HOURS:
Mon.- Frl. 8 a,m. to 5 p.m
= Operation
(CST)
. Customer Responsibilities
CAUTION:
• Service and Adjustment
Read and Follow
all Safety Rules
o Repair Parts
and Instructions
Before Operating
This Equipment
and CO., HoffmanEstates,' IL 60179 U.S.A.
SEARS, ROEBUCK
ページ2に含まれる内容の要旨
SAFETY RULES CAUTION: ALWAYS DISCONNECT SP/_K PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CON- TACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER, _' Always wear'eye protectionwhen you use this equip- TRAINING: ment orwhen youare in the vicinitywhere the equip- Engine exhaust gases containDEADLY carbonmon- ment is in use. oxide gas. l_is dangerous gas, if breathed in suffi- • Operate the pressure at no more than th
ページ3に含まれる内容の要旨
CONGRATULATIONS on your purchase of a Sears Crafts- PRODUCT SPECIFICATIONS man high pressure washer. It has been designed, engi- Pressure Washer Specifications neered and manufactured to give you the best possible dependability and performance. PUMP PRESSURE Adjustable to 1800 ps! FLOW RATE Should you experience any problem you cannot easily 2.5 gpm remedy, please contact your nearest Sears Service Cen- DETERGENT MIX tedDepartment or call the 1-800 number listed on the front Use undiluted deterg
ページ4に含まれる内容の要旨
TABLE OF CONTENTS SAFETY RULES ............................................................ 2 CUSTOMER RESPONSIBILITIES .......................... _4-15 PRODUCT SPECIFICATIONS ...................................... 3 SERVICE AND ADJUSTMENTS .................................. 16 ACCESSORIES AND ATTACHMENTS .......................... 5 STORAGE .................................................................... 17 CONTENTS OF HARDWARE PACK ..................................6 TROUBLESHOOTING ......
ページ5に含まれる内容の要旨
ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the high pressure washer was purchased,, They are also available at most Sears retail outlets and service centers. Most Sears stores can order these items for you when you provide the model number of your high pressure washer. Some of these accessories may not apply to your pressure washer° ® u 18" STAINLESS UTILITY BRUSH KIT ELECTRIC TURBO FLOOR/SIDING ROTATING BRUSH ANGLE EXTENSION STEEL EXTENSION KIT NOZZLE BRUS
ページ6に含まれる内容の要旨
CONTENTS OF HARDWARE PACK Parts packed separately in carton Parts Carton m ! Owner's Manual Gun and Wand Assembly Guide Handle Assembly (packed in flat carton) Main Unit (packed in flat carton) Parts packed In Parts Carton High Pressure Hose Detegent Pickup ': (2) Wheels Tube and Filter' MotQr Oit (3)Parts Bags ! Pads Bag contents not Pads Bag contents shown full size ,(fasteners) _ shown full size (2) Washers - M8 (2) Axle Pins (2) Support Leg Wire Support Assemblies !l[ifiJliirlliiFllIl![flti
ページ7に含まれる内容の要旨
ASSEMBLY Read these iv,sttuctions and Operator's Manual in its en- HOW TO SET UP YOUR PRESSURE WASHER tirety before you attempt to assemble or operate your new TO INSTALL THE WHEEL KIT high pressure washer° Your high pressure washer has, for the most part, been asserr_ed at the factory, except those Installing the wheel kit requires the tools listed, the guide parts left unassembted. Before you can operate your new handle and items included in the parts carton° highpressure washer, you must asse
ページ8に含まれる内容の要旨
ASSEMBLY Remove male connector to inspect Intake Supply o Attach wire support to guide handle with #10 self-dd!l- Screen in water inlet for cleanliness and inspect Inlet in_! screws and #10 fiat washers (Fig° 3). The hose Screen on female connector. Reattach male connector mlnder should be to the left and gun holder to the d_tht. to water inlet and attach female connector to garden Be sure loop of support is pointingupward. Place vinyl hose. cap onto gun holder. o Unravel high pressure hose, rem
ページ9に含まれる内容の要旨
OPERATION KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference,_ DETERGENT PICKUP TUBE AND RLTER SPARK PLUG HIGH PRESSURE HOSE GUIDE HANDLE OIL RLL OPENING ENGINE ON/OFF CONTROL CUP FOR WAND PRESSURE REGULATOR GUN AND WAND ASSEMBLY INLET WIRE SUPPORT t FEMALE C
ページ10に含まれる内容の要旨
OPERATION HOW TO USE YOUR WASHER IF YOU HAVE ANY PROBLEMS OPERATING YOUF.. , _=." _,_;_: PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-222-3136. STOPPING YOUR PRESSURE WASHEF_ _; First, move engine throttle lever to °OEW position(Fig 9). " OPTIONAL TURBO NOZZLE FIG. 11 FIG. 10 With the adjustable nozzle you can adjust the spray pattem to be either high pressure or low pressure, You can also OFFr-]IDLE FAST adjust the spray so it is concentrated in a stream pattern or I expan
ページ11に含まれる内容の要旨
OPERATION DETERGENT APPUCATION WITH ADJUSTABLE o Hook up water supply (Fig° 16). NOZ21JE o Adjust nozzle to select high pressure mode_ IMPORTANT: USE SOAPS DESIGNED SPECIFICALLY NOTE: Detergent will not flow when in the high pressure FOR PRESSURE WASHERS. HOUSEHOLD DETER- mode_ GENTS COULD DAMAGE THE PUMP° o Start washer and work from the top of the surface to IMPORTANT: YOU MUST ATTACH ALL HOSES BE- the bottom+ FORE YOU START THE ENGINE, STARTING THE EN- NOTE: The high pressure mode is most eff
ページ12に含まれる内容の要旨
OPERATION GAS NOTE: When adding oil to the engine crankcase in the WARNING: NEVER FILL FUEL TANK INDOORS. future, use only high quality detergent oil rated with API A NEVER RLL FUEL TANK WHEN ENGINE IS RUN- service classification SF, SG or SH rated SAE 30 weight. NING OR HOT. DO NOT SMOKE WHEN FILLING Use no special additives. Select the oil's viscosity grade FUEL TANK. according to your expected operating temperature. WARNING: NEVER FILL FUEL TANK COM- a, PLETELY FIJLL FILL TANK TO ABOUT 1/2" B
ページ13に含まれる内容の要旨
OPERATION TO START ENGINE IMPORTANT: DO NOT RUN PUMP WITHOUT THE WATER SUPPLY CONNECTED AND TURNED ON. YOU MUST FOLLOW THiS CAUTION OR THE PUMP WILL, BE DAMAGED_ o Press trigger on pressure washer wand to relieve high pressure and/or purge the inlet hose of air° o Move engine control lever to CHOKE position (Fig. 19). FIG. 21 NOTE: The engine is equipped with low oi! level shutdown system. The engine will not start unless the oil crankcase is filled to proper level. If engine shuts down during o
ページ14に含まれる内容の要旨
CUSTOMER RESPONSiBiLiTiES , i i ii ,,Jiiiiiiil,,,, Jl,i MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE HOURLY OPERATING INTERVAL REGULAR SERVICE Every25 Every100 Before Hoursor AfterFirst Hoursor SERVICE DATES 50 Hours Yearly MAINTENANCE TASK .... Each Use ....... Yearly PRESSURE WASHER Check/dean inletfillerandscreen _ Xt .................. Checkhighpressurehose. X ,, ,,,,,, ...... Checkdetergenthose. X Checkgunand wand forleaks. X Changepumpoil X:I: ........ ; ............... i,, ENGINE Ch
ページ15に含まれる内容の要旨
CUSTOMER RESPONSNBHUTY ENGINE MAINTENANCE PUMP MAINTENANCE CHECKING OIL LEVEL THE PUMP. WITHOUT THE PROPER TECHNIQUE, See "PREPARATION BEFORE USE" for information on ATTEMPTING TO DISASSEMBLE PUMP MAY checking oil level Oil level should be checked priorto each CAUSE PERSONAL INJURY. FOR SERVICE,CON- use or at least ever]/5 hours of operation,. Keep oil level I: WARNING: SULT A SEARS DO NOT AUTHORIZED ATTEMPT TO SERVICE DISASSEMBLE CENTER maintained.. OR CONTACT YOUR PLACE OF PURCHASE. CHANGING O
ページ16に含まれる内容の要旨
CUSTOMER RESPONSIBiLiTiES e Keep dirt and combustible debris off of muffler area, CLEAN OUT: CHAFF AND DIRT AIR CLEANER E[ FIG. 24 FIG. 25 o Service cartridge by tapping gently on a flat surface. Replace if dirty° Do not oil cartridge. o Insert cartridge (new or used) and reassemble cover to REPLACE SPARK PLUG base as it was removed before. Tighten cover screws securely. Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help CLEAN COOLING SYST
ページ17に含まれる内容の要旨
SERVICE AND ADJUSTMENTS O Remove additional debris by back flushing water sup- ply through wand. Back flush between 30 to 60 sec- onds,. Turn wand to stream spray and move nozzle from low to high while flushing. 0 Reinstall nozzle into the wand,, DO NOT overtighten, 0 Reconnect the wand to the gun o Reconnect the water supply, turn on the water, and start the engine.. Test the pressure washer by operating with nozzle in the high and in the low position. FIG. 26 STORAGE NOTE: As always, prepare t
ページ18に含まれる内容の要旨
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Pumphasfollowingp_oblems: 1. Nozzle in low pressure mode, 1,, Pull nozzle backwardfor high failure to pn_uce pressure,erratic pressuremode. pressure,chattering,lossof pressure, 2_ Low regulator pressure 2_ Adjustrogutatortodesiredsetting, lowwater volume. 3. Water inlet is blocked. 3. Clear inlet 4o Inadequate water supply 4. Provideadequate waterflow. 5o inlet hose is kinked or leaking 5o Straighteninlethose,patchleak. 6. 6o Checkandclean Inlet hosestrai
ページ19に含まれる内容の要旨
CRAFTSMAN 1800 PSi HIGH PRESSURE WASHER 580.751500 REPAIR PARTS \ \ N \, / L \ Parts List for this drawing and for drawing on Page 20 can be found on Page 21. 19 Drawing No,, 95087
ページ20に含まれる内容の要旨
CRAFTSMAN 1800 PSi HIGH PRESSURE WASHER 580.751500 REPAIR PARTS .< ! \ Drawing No, 95087 20
