ページ1に含まれる内容の要旨
User Manual
ページ2に含まれる内容の要旨
TABLE OF CONTENTS 1. BEFORE YOU BEGIN ....................................................................................................................................................... 3 WHAT IS INCLUDED ................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS ......................................................................................
ページ3に含まれる内容の要旨
1. BEFORE YOU BEGIN What is included • 1 x Abyss™ LED 2.0 • 1 x Power Cord • 1 x Warranty Card • 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save t
ページ4に含まれる内容の要旨
Safety Instructions Please read these instructions carefully. It includes important information about the installation, usage and maintenance of this product. • Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. • Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel
ページ5に含まれる内容の要旨
2. INTRODUCTION Product Overview Mounting Bracket DMX In DIP Switches Safety Power Out Bracket Adjustment Knob Bracket Adjustment Knob Power In DMX Out Fuseholder 2. Introduction 5 11/10/2010 3:19 PM
ページ6に含まれる内容の要旨
3. SETUP AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its average current draw under normal conditions. Always connect the fixture t
ページ7に含まれる内容の要旨
Mounting Orientation The Abyss™ LED 2.0 may be mounted in any position, provided there is adequate room for ventilation. Rigging Be sure that the structure can support the weight of the fixture. Please see the “Technical Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm in size. When rigging consider routine maintenance and cont
ページ8に含まれる内容の要旨
4. OPERATING INSTRUCTIONS Configuring the Starting Address The Abyss™ LED 2.0 fixture uses two DMX channels. The highest channel that the fixture may be set to in order to function properly is 511. Any address higher than this will prevent access to all of the channels. If this is your first time using DMX, we recommend reading the “DMX Primer” section in the “Appendix”. DMX Operation This is the operating mode which will allow for control with an external DMX controller
ページ9に含まれる内容の要旨
Standalone This fixture has preprogrammed operating modes. These are accessed via the DIP switches on the back of the fixture. DIP switch [10] must be OFF in this mode. Please see the chart below for further explanation. Mode DIP switches Water effect rotating, color rotating 1 = ON Water effect static, color rotating 2 = ON Water effect rotating, color static 3 = ON Water effect static, color static 4 = ON The DIP switches will not work together. Only use one out of the 4 mod
ページ10に含まれる内容の要旨
5. APPENDIX General Troubleshooting SYMPTOM POSSIBLE CAUSE(S) POSSIBLE ACTION(S) • Check total load placed on the • Excessive circuit load electrical circuit. Breaker/Fuse keeps blowing • Short circuit along the power • Check for a short in the electrical wires wiring (internal and/or external). • No power • Check for power on Mains. Device does not power up • Loose power cord • Check power cord • Check Control Panel and unit • Wrong DMX addressing addressing • Damaged
ページ11に含まれる内容の要旨
DMX Primer There are 512 channels in a DMX connection. A fixture capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required. Choosing a start address should be planned in advance. Channels should never overlap. If they do, this will
ページ12に含まれる内容の要旨
Cable Connectors Cabling must have a male XLR connector on one end and a female XLR connector on the other end. DMX connector configuration COMMON 1 1 DMX + INPUT 3 OUTPUT 3 2 2 DMX - Terminator To avoid signal transmission problems and interference, it is always advisable to connect a DMX signal terminator. 1 3 2 120 ohm ¼ W resistor between pin 2 (DMX -) and pin 3 (DMX +) on the output of the last fixture Do not allow contact between the common and the fixture’s chassis
ページ13に含まれる内容の要旨
3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin adapter. The chart below details a proper cable conversion: 3-PIN TO 5-PIN CONVERSION CHART Conductor 3-Pin Female (Output) 5-Pin Male (Input) Ground/Shield Pin 1 Pin 1 Data ( - ) signal Pin 2 Pin 2 Data ( + ) signal Pin 3 Pin 3 Not used Pin 4 Not used Pin 5 Setting up a DMX Daisy Chain 1. Connect the (male) 3-pin connector side of Univer
ページ14に含まれる内容の要旨
General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. • Unplug fixture from power. • Us
ページ15に含まれる内容の要旨
TECHNICAL SPECIFICATIONS WEIGHT & DIMENSIONS Length ............................................................................................................. 9.6 in (243 mm) Width ............................................................................................................. 10.2 in (260 mm) Height .............................................................................................................. 7.4 in (188 mm) Weight .....................................
ページ16に含まれる内容の要旨
CONTACT US World Wide General Information CHAUVET® th 5200 NW 108 Ave Sunrise, FL 33351 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084 Technical Support CHAUVET® th 5200 NW 108 Ave Sunrise, FL 33351 voice: 954.929.1115 (Press 4) fax: 954.929.5560 (Attention: Service) World Wide Web www.chauvetlighting.com
