ページ1に含まれる内容の要旨
Model No. IMTL94106.0
Serial No.
Write the serial number in the space
USER'S MANUAL
above for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-800-753-4645
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
CAUTION
Visit our website at
Read all precautions and instruc
ページ2に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 T
ページ3に含まれる内容の要旨
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating the treadmill. 1. It is the responsibility of the owner to ensure 11. Failure to use a properly functioning surge that all users of this treadmill are adequately suppressor could result in damage to the con- informed of all warnings and precautions. trol system of the treadmill. If the control sys- tem is damaged, the wa
ページ4に含まれる内容の要旨
20. Do not attempt to raise, lower, or move the 27. An outside antenna system should not be lo- treadmill until it is properly assembled. (See cated in the vicinity of overhead power lines ASSEMBLY on page 7, and HOW TO FOLD or other electric light or power circuits, or AND MOVE THE TREADMILL on page 22.) where it can fall into such power lines or cir- You must be able to safely lift 45 pounds (20 cuits. When installing an outside antenna kg) to raise, lower, or move the treadmill. system, extre
ページ5に含まれる内容の要旨
Power Lines Ground Standoff Clamp Insulators Service Entrance Mast To External Antenna Conductors Terminal of Treadmill Antenna Lead-in Wire Service Ground Entrance Antenna Wire Equipment Discharge Unit Ground Wire Power Service Grounding Electrode System (e.g. Ground Ground Bonding Interior Metal Water Pipe) Clamps Clamps Jumper Optional Antenna Grounding Electrode Driven 8 Feet (2.44m) Into The Earth (If Required By Local Codes). See NEC Section 810–21 (f). WARNING: Before beginning this or a
ページ6に含まれる内容の要旨
BEFORE YOU BEGIN ® Congratulations for purchasing the IMAGE AD- manual. To help us assist you, note the product model VANCED 2200 treadmill. The ADVANCED 2200 tread- number and serial number before contacting us. The mill offers an impressive array of features designed to model number of the treadmill is IMTL94106.0. The se- help you achieve your fitness goals in the convenience rial number can be found on a decal attached to the of your home. From the advanced console to the cush- treadmill (se
ページ7に含まれる内容の要旨
ASSEMBLY To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly requires two persons. Place the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until the treadmill is assembled. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking
ページ8に含まれる内容の要旨
3. With the help of a second person, raise the treadmill 3 Frame (55). Hold the Latch Housing (68) and the Latch Housing Cover (5) against the sides of the Frame as shown. Loosely thread the two blunt-tipped 1/2” Screws (132) into the Latch Housing Cover and the Latch Housing as shown. Do not tighten the Screws yet. Hole Knob Remove the knob from the pin. Make sure that the collar and the spring are on the pin. The collar should be on the 132 side of the spring shown. Insert the pin into the Lat
ページ9に含まれる内容の要旨
Before the personal television can be used, you must connect an antenna, a 75 ohm CATV cable, or a VCR to the 75 ohm antenna terminal on the treadmill frame. Note: No antenna, cable, or adapter is included. HOW TO CONNECT AN ANTENNA 300 Ohm Flat Wire Indoor Antenna 1. See the drawing near the bottom of this page. Connect the 300 ohm flat wire from the antenna to a 1. Place a VHF 300 ohm to 75 ohm adapter. antenna in the Screwdriver desired loca- 2. Push the 300 ohm to 75 ohm adapter onto the 75
ページ10に含まれる内容の要旨
TREADMILL OPERATION THE PRE-LUBRICATED WALKING BELT tric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding Your treadmill features a walking belt coated with high- plug. Plug the power cord into a surge suppressor, performance lubricant. IMPORTANT: Never apply sil- and plug the surge suppressor into an appropriate icone spray or other substances to the walking outlet that is properly installed and grounded in belt or the walking platform. Such su
ページ11に含まれる内容の要旨
Key Clip FEATURES OF THE CONSOLE treadmill to keep your heart rate near target heart rate settings while you exercise. The treadmill console offers an impressive array of features designed to help you get the most from your Whether you select the manual mode or a program, workouts. you can enjoy the shows of your choice on the per- sonal television while you get in shape. When the manual mode of the console is selected, the speed and incline of the treadmill can be changed with To use the manu
ページ12に含まれる内容の要旨
If one of the numbered Speed buttons is pressed, HOW TO TURN ON THE POWER the walking belt will gradually increase in speed until it reaches the selected speed setting. Plug in the power cord (see page 10). To stop the walking belt, press the Stop button. Next, locate the reset/off The time will begin to flash in the left display. To circuit breaker near the restart the walking belt, press the Start button, the power cord. Make sure that Reset Speed increase button, or one of the numbered the
ページ13に含まれる内容の要旨
The right display—This display will show the dis- make sure that your hands are clean. Next, hold tance that you have walked or run, the number of the handgrip pulse sensor with your palms resting 1/4-mile laps you have completed, the speed of on the metal contacts; avoid moving your hands. the walking belt, and the approximate numbers of When your pulse is detected, the heart-shaped in- calories and fat calories you have burned (see dicator in the right display will flash each time your FAT BUR
ページ14に含まれる内容の要旨
The speed setting for the HOW TO USE A PRESET PROGRAM Current Segment first segment will be Column shown in the flashing Insert the key into the console. Current Segment column 1 of the matrix. (The in- See HOW TO TURN ON THE POWER on cline settings are not page 12. shown in the matrix.) The speed settings for Select a preset program. the next seven segments 2 will be shown in the columns at the right. To select a preset program, press the Speed & Incline button repeatedly. The right display wi
ページ15に含まれる内容の要旨
To stop the program at any time, press the Stop Turn on the fan if desired. 6 button. The time will begin to flash in the left dis- play. To restart the program, press the Start button See step 7 on page 13. or the Speed increase button. The walking belt will begin to move at 1 mph. When the next segment When you are finished exercising, remove the 7 of the program begins, the treadmill will automati- key from the console. cally adjust to the speed and incline settings for the next segment. When
ページ16に含まれる内容の要旨
See the matrix in the left HOW TO CREATE A CUSTOM PROGRAM Current Segment display. Each custom Column program is divided into Insert the key into the console. one-minute segments. 1 One speed setting and See HOW TO TURN ON THE POWER on one incline setting can page 12. be programmed for each segment. The speed set- Select a custom program. ting for the first segment 2 will be shown in the flashing Current Segment col- To select a custom program, press the Custom umn of the matrix. (The incline
ページ17に含まれる内容の要旨
ries of tones will sound, the speed setting and the HOW TO USE A CUSTOM PROGRAM incline setting will flash in the displays, and all speed settings will move one column to the left. Insert the key into the console. The speed setting for the second segment will then 1 be shown in the flashing Current Segment column See HOW TO TURN ON THE POWER on and the treadmill will automatically adjust to the page 12. second speed and incline settings that you pro- grammed previously. Select a custom program
ページ18に含まれる内容の要旨
Enter your age. HOW TO USE A HEART RATE PROGRAM 3 When a heart rate program is selected, the word “AGE” and the current age setting will begin to flash in the right display. If you have already en- CAUTION: If you have heart prob- tered your age, press the Enter button. If you have lems, or if you are over 60 years of age and not entered your age, press the + or – button be- have been inactive, do not use the heart rate side the Enter button to enter your age, and then programs. If you are takin
ページ19に含まれる内容の要旨
Hold the handgrip pulse sensor. During all heart rate programs, the console will 5 regularly compare your heart rate to the target It is not necessary to hold the handgrip pulse sen- heart rate setting for the current segment. If your sor continuously during a pulse program; how- heart rate is too far below or above the target ever, you must hold the handgrip pulse sensor fre- heart rate setting, the speed of the walking belt quently. Each time you hold the handgrip pulse will automatically incr
ページ20に含まれる内容の要旨
HOW TO OPERATE THE PERSONAL TELEVISION HOW TO USE THE INFORMATION MODE The console features an information mode that allows IMPORTANT: Before operating the television, you you to view treadmill usage information, select a sys- must connect an antenna, a 75 ohm CATV cable, or tem of measurement for the console, and turn on and a VCR to the 75 ohm antenna terminal on the tread- turn off the demo mode. The information mode also al- mill. See page 9 for instructions. lows you to adjust the settings
