ページ1に含まれる内容の要旨
Automatic Drum
Washing Machine
HA1000TE HA800TE HA600TE
Table of Contents
Before using
Names of Parts---------------------------------inside front cover
Matters Needing Attention-------------------------------------1-3
Installation---------------------------------------------------------4-5
Control Panel--------------------------------------------------------6
Operational Functions-----------------------------------------6-7
During using
Program Selection----------------------------------------
ページ2に含まれる内容の要旨
NamesofParts Table Cover Washing Allocating box Operation Button Program Knob Wash Door Observing Glass Window Temperature knob Power supply cable Earth terminal Drainage hose clip Packing bolt (3) Back plate screw (3) Drainage hose Back plate CautionandWarningsymbols For your safety, any instructions in this manual with this "Warning" sign shall be strictly followed. For your safety and to prevent damages to the washing machine, any instructions in this manual with this "Stop" sign shall be str
ページ3に含まれる内容の要旨
MattersNeedingAttention Safety 2. Hold the plug and not the electric cable 1. A separate earthed socket is required when unplugging the washing machine. for the power supply. After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated 4. For your safety, dry hands before touch- for 15A. Refer to a washing machine techni- ing the washing machine and wear appropri- cian or a Haier designated service point for
ページ4に含まれる内容の要旨
MattersNeedingAttention Use 2
ページ5に含まれる内容の要旨
MattersNeedingAttention 3. Never place heavy objects ,a heating 4. Do not wash foam rubber or similar sponge materials. applianceor a water container on the top panel of the washing machine. 5. Before washing, do up zippers, buttons , 6. Do not open the detergent box during laces and repair damaged areas,under- the wash cycle. wear or small articals should be placed in the laundry bag or a pillowslip. Do not wash clothes containing wire frames. 8. After washing, turn off the tap to prevent 7. Th
ページ6に含まれる内容の要旨
Installation As shown in figure1 remove all the packing materials (including the foam base). Upon opening of the package, water drops may be seen on the plastic bag and the porthole. This in normal phenomenon resultingfrom water test in the factory. Fig 1 Check attachments and materials. Name Operational Quality Water Drainage Plastic Qty manual hose holder plugs certificate Model HA1000TE HA800TE 1 1 1 1 3 HA600TE Remove the packing screws as shown in figure 2. The packing bolts protect the
ページ7に含まれる内容の要旨
Installation Connectionofwaterinlethoseandwashingmachine . Waterdrainagehose The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine. Use the water drainage support supplied as an accessory for proper installation of the water drain- age hose .fix the water drainage hose support with waterproof sring.Do not use an excessively long wa- ter drainage hose and contract the autho
ページ8に含まれる内容の要旨
ControlPanel 0 15 1 14 2 13 3 90 30 4 12 80 40 5 11 70 50 6 10 60 9 7 8 H 0 15 1 14 2 13 3 Turn the knob at "0", then turn off the power and 12 4 5 turn the program knob for setting desired wash program. 11 6 10 7 9 The program knob will not rotate with the programmed washing 8 process. 90 30 80 40 70 50 60 6
ページ9に含まれる内容の要旨
OperationalFunctions Soak Button For the synthetics cycle and the wool cycle, push the button down, the anticrease funtion will be skiped and automatically enter into the next step;Release the button, the anti-crease funtion willwork again. Economic Wash button It reduces water and power consumption when rinsingifthemachinedoesnothaveafullload. Note: Select this function when "Cotton" "Synthetics", "Wool" or "Silk" (programs 1-12) is selected. 7
ページ10に含まれる内容の要旨
ProgramSelection HA1000TE/HA800TE/HA600TE Program Setting Laundry Temperature -30-40-50-60 * 1 Intense Very heavy soil -70-80-90 -30-40-50-60 2 Heavy soil Prewash * 3 -30-40-50-60 Normal Soiled cotton * Non-fade and medium 4 Middle -30-40 soiled cotton * Fading and medium 5 Delicate soiled cotton * Non-fade heavily 6 Normal -30-40-50-60 soiled chemical fiber * Non-fade and medium 7 Middle -30-40 soiled chemical fiber * Fading and medium 8 Delicate soiled chemical fiber * Non-fade heavily soil
ページ11に含まれる内容の要旨
Preparation 2.Watersupply 1.Powersupply Turn on the tap ensure that the water is clear. Plug in the power supply Caution: Before staring the washing machine turn on the 220V~240V/50Hz. water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak. 3.Laundrytreament 4.Detergentselection Only special low foam detergent sort out clothes according to type and extent of dirt. should be used in automatic There are three types of clothes: cotton, synthet
ページ12に含まれる内容の要旨
WashingMethods 1.Laundryloading Reference loading Evenly load the laundry in the Overalls Jeans (800g) washing machine and then tightly (cotton 950g) close the door of the washing Pajamas (200g) machine Blended Note: 1) When first using the fabric clothes washing machine, let it run un- (800g) Shirts loaded for one program to pre- (300g) shirt vent the laundry from being Underwear (cotton tainted by oil or dirty water from (blended fabrics 70g) 300g) the washing machine. 2) Do not Socks
ページ13に含まれる内容の要旨
WashingMethods 4.Washingtemperature Setting Set the washing temperature as required, otherwise, set at position * when heating is not needed. 5.Selectingthefunctionbutton Select function buttons as required (refer to the directions printed on the control panel) , otherwise keep all the button released. 6.Washing Press the power button and the washing machine will automatically commence the pro- grammed washing process. Caution: The program knob will not rotate with the programmed washing process
ページ14に含まれる内容の要旨
OtherFunctions 1. Power-off memory funtion: This machine has a power-off menmory funtion. In case of abrupt power failure or the power must be cut off during a program cycle, the present settings will be saved, and operation will resume when the power is switched on again. 2. Trouble messages: judge the malfunctions from door lock light Error 1: The door lock light does not illuminate. Cause: Door is not properly shut. Correction: Shut the door properly. Error 2: The door lock light glitters 2 t
ページ15に含まれる内容の要旨
Maintenance 2. Unplug the machine during cleaning and 1. Turn of the water and electricity supply af- maintenance. Use a soft cloth dampened ter every wash. Open the door to prevent the formation of moisture and odors. If the wash- with soapy liquid to clean the machine case and rubber components. Do not use corro- ing machine is left idle for a long period, drain any remaining water in the machine and re- sive or abrasive chemicals or solvents. place the drainage hose. 4. To prevent blockages t
ページ16に含まれる内容の要旨
Trouble shooting The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed. Problem Possible Cause Poor connection to power supply Power failure The washing machine fails to Door is not properly closed operate Machine has not been switched on Water is not turned on Water pressure is less than 0.03MPa Washing machine does not fill The inlet hose is kinked with water Water supply failure The program knob is not prop
ページ17に含まれる内容の要旨
TechnicalSpecification Model Item HA1000TE HA800TE HA600TE 220V~240V/50Hz 220V~240V/50Hz 220V~240V/50Hz Power supply 15 15 15 Maximum working current (A) Water pressure (MPa) 0.03 P 1 0.03 P 1 0.03 P 1 Washing power (W) 230 230 230 Spinning power (W) 400 380 340 Max. washing load (kg) 5 5 5 Spinning speed (r/min) 1000 800 600 Washing program 15 15 15 Maximum power (W) 2000 2000 2000 Size (mm) 850x520x595 850x520x595 850x520x595 65 65 W eight (kg) 65 Net
ページ18に含まれる内容の要旨
WiringCircuit Motor M7 M8 R T S M1 M2 M3 M5 CN1-2 CN2-1 CN1-3 CN1-1 CN3-3 CN3-1 MR CN2-2 CN6-4 MRN NTC MRL CN6-3 MRC CON3 PCB SW N CON2 G CN2-3 EVF FA CON1 L EVP CN2-4 CN2-5 CN2-6 CON3 CN3-3 CN3-4 12 13 EVC PS 14 R 11 P PCB-PrintedCircuitBoard Motor-Motor MR-DoorLock R-HeatingElement PS-DrainPump P-PressureSwitch EVP,EVF-ColdwaterValve EVS-HotWaterValve FA-InterferenceSuppresser NTC-TemperatureSensor SW-PowerSwitch Motor-Motor 16
