ページ8に含まれる内容の要旨
Before using Before using Install the water inlet hose Install the water inlet hose 1. Insert a new flat washer into each end of the inlet hoses. Firmly put the washers in the coupling. Note: Use the new hose sets supplied with the washer. Any other old hose sets should not be used. You may have to use pliers to tighten the coupling. Do not over tighten because you may cause damage to the valve. 2. Connect the water inlet hoses to the water faucet. 3. Connect the other ends to their resp
ページ9に含まれる内容の要旨
Using process 1 Preparation before washing Using process Preparation before washing 1. Connect the water inlet hose. 2. Confirm that the washing machine is earthed reliably. Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3. Hang up the drain hose. Pay attention to followings before washing the laundries Confirm if Clear the pocket. Fasten the The quantity of When the pulsator there's special Take out th
ページ10に含まれる内容の要旨
Using process 2 Put in the laundries Using process The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity. The largest capacity of this machine is 5.0kg. The thickness, size, type of the cloth will influence the actual washing capacity. It is suitable for one time washing to put in reasonable amount of laundries and
ページ11に含まれる内容の要旨
Using process 3 Put in the detergent Using process Inlet for concentrated washing powder and detergent How to use the washing powder Direct dissolved in the machine 1.Fill water to "Low" water level. 2.Add the power. Run for 30 seconds to dissolve it completely. 3.Put in the laundries. Select Detergent box suitable water level. The instant dissolving of the washing How to use the whitener powder: 1.Prepare warm water of 30 and a container. Fill water to decided level. Dilute the whitener with
ページ12に含まれる内容の要旨
Using process Using process 4 Use the operation buttons a. Description of the function of the buttons SURPLUS(MIN) To indicate -- during sensing. To indicate remaining min. During program running. To indicate remaining reserved time (hrs) during reservation period. To indicate fault symbols for abnormal conditions (see page 15) Page 15 PROGRAM STATUS PROCEDURE STATUS STANDARD SOAK HEAVY WASH GENTLE RINSE QUICK WASH SPIN WASH SPIN PROGRAM RESERVATION WATER LEVEL " WATER LEVEL"button Press"PROGRA
ページ13に含まれる内容の要旨
Using process Using process "POWER ON/OFF"button Press "Power On/Off" button to connect power supply. After power is connected, pressing this button will cut off the supply. "START/PAUSE"button After the power is switched on, press it to start the machine During working, push it to pause working. During pause, push this button to restart and continue operation. XQB50-10A POWER START ON/OFF PAUSE Remarks: After pressing "Power On/Off" to connect power supply, if the washing machine
ページ14に含まれる内容の要旨
Using process Using process b. Operating procedure and explanations for the buttons PROGRAM PROGRAM ST STA AT TUS US PROCEDURE PROCEDURE ST STA AT TUS US XQB50-10A ST STANDARD ANDARD SOAK SOAK HEAVY WA WASH SH GENTLE GENTLE RINSE RINSE QUICK QUICK W WASH ASH SPIN SPIN WA WASH SH POWER POWER ST STAR ART T ON/OFF ON/OFF SPIN SPIN PA PAUSE USE PROGRAM PROGRAM RESER RESERV VA AT TION ION W WA ATER TER L LEVEL EVEL 1 Press the "Power On/Off" button to switch on the power supply POWER POWER ON/OFF
ページ15に含まれる内容の要旨
Using process Using process Attention Even there's no water in the tub, the spinning will start after a certain period. Do not use soak process for woolen laundries. Wash the laundries that are prone to lose colors separately from other laundries. The pulsator will not rotate unless the water is filled to selected water level. Selection method of the procedure programs Times of pushing Selected procedure Corresponding Total Time the"Program program Applicable procedure program select"button
ページ16に含まれる内容の要旨
Using process Using process Total time: including the normal water inlet time, drain time, excluding the power off time. The total washing time may be influenced by the water inlet pressure and water level. Spin time: the time from intermittent running to finishing. The Jeans program could combine the process of soak during which the washing machine firstly soak for about 25~45 min after water filling and then begins to wash. When "Quick wash" program is chosen, the washing machine would automa
ページ17に含まれる内容の要旨
Using process Using process 6 Finish washing The washing machine cuts off the power supply automatically when wash cycle ends. After Finishing wash alarm automatically 7 Disposal after washing After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. When washing, lint filter must be used After using, please clean it in time. Lint filter
ページ18に含まれる内容の要旨
Trouble shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department . Do not repair it by yourself. Phenomena The reason How to settle Buzzing upon reservation starts, The top lid is not closed Close the top lid Nixie tube indicates "E0" Put down the drain hose. Open Is the
ページ19に含まれる内容の要旨
Common phenomena Phenomena Explanation The spinning is intermittent when it starts. Balance the laundries to avoid slanting. Push the"PROGRAM /RESERVATION" button to The program is setting the drain time. Some time is select "Spin", but it doesn't work. needed before it starts spinning. There may be some water flowing out of It is the water remained in the factory inspection of the drain hose in the first use of the machine. performance. While wa
ページ20に含まれる内容の要旨
Specification Specification XQB50-10A Model 5.0kg Rated washing / spinning capacity Lowest/20L Low/30L Mid/37L High/48L Water level/Water quantity (about) About 144L (High water level; Standard program) Max water consumption 0.03MPa-0.78MPa Water inlet pressure 325W Rated washing power Rated spinning power 285W Weight About 39kg Dimension L 510mm W 500mm H 882mm
