ページ1に含まれる内容の要旨
INSTALLATION, OPERATING
& SERVICE INSTRUCTIONS
FOR MASTER SERIES
HEAVY DUTY GAS FRYERS
MODELS M/MST35 & M/MST70
WARNING:
IMPROPER INSTALLATION, ADJUSTMENT,
FOR YOUR SAFETY
ALTERATION, SERVICE OR MAINTENANCE CAN
CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
DO NOT STORE OR USE GASOLINE OR OTHER
READ THE INSTALLATION, OPERATION AND
FLAMMABLE VAPORS OR LIQUIDS IN THE
MAINTENANCE INSTRUCTIONS THOROUGHLY
VICINITY OF THIS OR ANY OTHER APPLIANCE.
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
PLEASE READ
ページ2に含まれる内容の要旨
IMPORTANT INFORMATION WARNING: This product contains chemicals known NOTE: Before leaving the factory, the fryer was tested to the State of California to cause cancer and/or birth with oil in the frypot; therefore, it is necessary to clean defects or other reproductive harm. Installation and the frypot before adding frying compound. Rinse the servicing of this product could expose you to airborne frypot with clean water, then put some fryer cleaner on particles of glasswool/ceramic fibers. In
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Important Information................ 2 Cleaning And Maintenance ........... 13 Routine Care ....................... 13 Dimensions And Specifications, Cleaning ............................. 13 Model M/MST35.................... 4 Painted Finishes ..................... 13 Dimensions And Specifications, Stainless Steel ....................... 14 Model M/MST70.................... 5 Draining and Filtering Of Fryer Compound 14 Installation......................... 6 Maintenance .....
ページ4に含まれる内容の要旨
DIMENSIONS AND SPECIFICATIONS, MODEL M/MST35 3-1/2" [89mm] CLEARANCES SHIPPING INSTALLATION ENTRY WEIGHT Sides Rear Crated Uncrated 37-7/8" 34-3/8" 6" 6" 29-1/4" 17-1/4" 220lb. [962mm] [873mm] (152mm) (152mm) (746mm) (618mm) (100kg) 13-1/8" [333mm] 33-3/8" [848mm] 31-1/2" [800mm] 46-3/4" [1187mm] With "BG" BACKGUARD 40-1/4" 63-3/4" [1619mm] [1022mm] 1-1/4" N.P.T. 30-1/4" With "LPBG" With "DDBG" [32mm] [768mm] BACKGUARD BACKGUARD 33-7/8" GAS INLET [860mm] 6" [152mm] 17" 34" [432mm] [864mm] OPERA
ページ5に含まれる内容の要旨
DIMENSIONS AND SPECIFICATIONS, MODEL M/MST70 33-3/8" [848mm] 31-1/2" 46-3/4" [800mm] [1187mm] W/"BG" BACKGUARD 40-1/4" 63-3/4" [1022mm] [1619mm] 1-1/4"N.P.T. 30-3/8" W/"LPBG" W/"DDBG" [32mm] [772mm] BACKGUARD BACKGUARD 33-7/8" GASINLET [860mm] 6" [152mm] 24" 34" [610mm] [864mm] 3-1/2" [89mm] DIMENSIONS & SPECIFICATIONS Width 24"(612mm) Depth 38" (965mm Height (w/ NSF Legs) 36-3/8" (924mm) Height (w/o NSF Legs) 30-3/8" (772mm) 37-7/8" 34-3/8" [962mm] Input-BTU (Natural Gas) 125,000 (36.62 kW) [87
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
INSTALLATION Continued NOTE: This appliance is not recommended for Casters residential installation. A. The installation shall be made with a connector that complies with the standard for connectors Clearances for Movable Gas Appliances, ANSI Z21.69 or From Combustible material ” (mm) sides and rear. the Standard for Connectors for Movable Gas A clearance of .” to non combustible construction Appliances, CAN/CGS-6.16, and quick disconnect as sides & rear is acceptable. The fryer i
ページ8に含まれる内容の要旨
INSTALLATION Continued the front of the unit for servicing and proper operation. Ventilation and Air Supply Air for combustion enters the unit below the cabinet One of the most important considerations is ventilation. at the base. Do not place anything around the base or The fryer must be installed so that products of combustions under the fryer. are removed efficiently, but so that the kitchen ventilation system does not produce drafts that interfere with proper Assembly Of Battery burner
ページ9に含まれる内容の要旨
INSTALLATION Continued E. The manifold of this unit or the manifold of which Assembly Instructions M-Series Backguard is a part of must be equipped with a certified 1. Remove front panel #5 by lifting upward. pressure regulator suitable for battery application 2. With back panel #4 still attached to the left #2 and and adjustable for an outlet pressure at the manifold right #3 uprights, drop uprights into the rectangular as specified on the rating place cutouts at the rear of the range. Asse
ページ10に含まれる内容の要旨
INSTALLATION Continued METHOD OF ATTACHING RADIATION SHIELD TO BACKGUARD OR HIGH SHELF RADIATION SHIELD REMOVE EXISTING #10 SHEET METAL SCREWS (2 REQ'D) FROM HIGH SHELF OR BACKGUARD TO INSTALL RADIATION SHIELD FIGURE 1 Radiation Shield SIDES AND FRONT This radiation shield must be in place when fryer is BACK ALUMINIZED installed in other than fire resistive locations. HEAT SHIELD IMPORTANT: The flue riser must be installed within FLUE RISER the back guard. This rectangular riser fits over the col
ページ11に含まれる内容の要旨
OFF O L I T P O L I P T NO OPERATION Continued according to the instructions in the Cleaning and NOTE: Fryer cannot be shut off at the thermostat. Maintenance Section of this manual. Thermostat used only to control temperatures. Lighting Instructions Stand By For specific models see “Lighting Instructions” on the 1. Turn fryer gas valve knob to “PILOT” position. inside of fryer compartment. 2. Put frypot cover in place. (Frypot must be filled before lighting). Complete Shut Down 1. Turn thermostat
ページ12に含まれる内容の要旨
OPERATION Continued Optimum Operation Tips FRYING CHART Product Temperature Time One of the most important considerations in the profitable use of a fryer is the choice of the frying compound used. French Fried Potatoes A better frying compound will actually cost you less, Raw-to-done 350 5-7 Min because it lasts longer than the lower grades and produce Blanching 325 4 Min fried foods with superior taste and appearance. There Browning 350 2 Min are numerous high-grade products available and
ページ13に含まれる内容の要旨
OPERATION Continued • Do not salt or otherwise season food over the fryer. • Watch for signs of compound breakdown. An This practice contaminates the frying compound unusual darkening of the compound or smoking are and accelerates it deterioration. the first signs of breakdown. Foaming, objectionable change in flavour of the product and gumming also • Do not shake breaded items over the fryer. indicate a breakdown of the frying compound. • Keep the frypot covered when not in use. This will •
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
CLEANING AND MAINTENANCE Continued 1. Check pilot flame for correct length. Preventive Maintenance 2. Check main burner flames for good ignition and In order to keep the unit operation at top efficiency, it is proper burner adjustment. advisable to perform preventive maintenance regularly. The frequency of this maintenance will depend on how 3. Check thermostat calibration. hard the unit is used, and you should discuss this with 4. Check thermopile output your nearest GARLAND authorized Service
ページ16に含まれる内容の要旨
ページ17に含まれる内容の要旨
NOTES Part # 1382677 (08/06) Page 17
ページ18に含まれる内容の要旨
NOTES Page 18 Part # 1382677 (08/06)
ページ19に含まれる内容の要旨
DÉPANNAGE ET RÉGLAGES suite NOTE: NE PAS FAIRE PIVOTER LA TIGE Directives Pour Le Calibrage Du Th ermostat D’AJUSTEMENT PLUS DE DEUX FOIS DANS UN Pour calibrer le Th ermostat Fenwal, remplir la friteuse SENS OU DANS L’AUTRE SINON DU DOMMAGE jusqu’à la marque « FULL » (plein) avec du composé à PERMANENT PEUT EN RÉSULTER. CETTE friture et allumer le brûleur. Introduire un thermomètre PRATIQUE PEUT ANNULER LA GARANTIE dans le centre de la friteuse, et placer le bulbe à environ STANDARD. de
ページ20に含まれる内容の要旨
DÉPANNAGE ET RÉGLAGES Réglages Dépannage Le brûleur de votre Friteuse GARLAND, de conception Un appareil mécanique utilisé aussi intensément qu’une brevetée, ne demande pas d’air primaire donc aucun friteuse aura besoin d’un entretien de service au fur et à ajustement possible. Lorsque le type de gaz requis mesure qu’elle vieillira; donc, le tableau suivant indique est utilisé, à la pression requise, et que les cibles en les problèmes probables qui surviendront et que faire céramiques sont
