ページ1に含まれる内容の要旨
Full Size Ice Maker
Models:
IB650SS, IB1000SS, IB1500SS
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
ページ2に含まれる内容の要旨
Important Safety Information Improper handling can cause serious damage to the EdgeStar ice maker and/or injury to the user. This ice maker is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet. Please read and follow the
ページ3に含まれる内容の要旨
Table of Contents IMPORTANT SAFETY INFORMATION ................................................................. I INTRODUCTION ................................................................................................... 1 PARTS IDENTIFICATION ..................................................................................... 2 INSTALLING THE ICE MAKER ............................................................................ 3 TYPES OF INSTALLATION.......................
ページ4に含まれる内容の要旨
Introduction Thank you for purchasing this EdgeStar ice maker. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and EdgeStar. We will provide the customer support needed to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your ice maker. Following this manual will ensure that your product will work at its peak performance and efficiency. Please sa
ページ5に含まれる内容の要旨
Parts Identification Top cover Door Ice cube full sensor Right side Front cover Ventilation Ice storage bin louvers Ice scoop Leveling Leg Control box (Behind front cover) Power switch EdgeStar Full Size Ice Maker 2
ページ6に含まれる内容の要旨
Installing the Ice Maker The ice maker should be installed by a licensed plumber to be in accordance with local electrical and plumbing code requirements. Before you plug the ice maker in to a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle. Unpacking the Ice Maker WARNING: Use two more people to move and install the ice maker. Failure to do so can result in back or other injury. Carefully remove the packaging materi
ページ7に含まれる内容の要旨
Installation Clearance Requirements * This icemaker should be installed by a licensed 4” plumber only. * To ensure proper service access and ventilation, Top of Unit allow more 4” clearance at rear, and 1/2” at top and 1/2” at sides. The installation should allow the icemaker to be pulled forward for servicing if 1/2” 1/2” necessary. * When installing the ice maker under a counter, follow the recommended spacing dimensions shown. Place electrical and water supplies and drain f
ページ8に含まれる内容の要旨
Electrical Requirements Electrical Shock Hazard Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter. Never use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death Before you move your icemaker into its final location, it is important to make sure you have the proper electrical connection: A standard electrical supply (115 V, 60Hz.), properly
ページ9に含まれる内容の要旨
Water Supply Connections The water supply should be ready at the point of installation. The water supply pressure should be a minimum of 20 psig with a static pressure not more than 80 psig. (A wall outlet directly behind the ice maker will make installation easier.) IMPORTANT: 1. All installations must be in accordance with local plumbing code requirements. 2. Make certain that the pipes are not pinched or kinked or damaged during installation. 3. Check for leaks after connection.
ページ10に含まれる内容の要旨
OPERATION Final Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you clean the ice storage bin? 3. Have the installation instructions been followed, including connecting the machine to water and electricity? Does the unit have proper drainage? 4. Has the machine been leveled? 5. Is the ice maker in a site where the ambient temperature is between 55º F and 90ºF and the water temperature between 41º F
ページ11に含まれる内容の要旨
How the machine Makes Ice Turn the power switch to the ON position. The machine will automatically start the ice making stage. There are two distinct cycles: freeze and harvest. During the freeze cycle, water is sprayed against the evaporator surface. In the harvest cycle, the ice is released and water enters the machine. A complete cycle can take 20 to 40 minutes, depending on temperature and operating conditions. Freeze: During the freeze cycle the compressor is pumping refrigerant, th
ページ12に含まれる内容の要旨
Normal Sounds Your new icemaker may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. Ratting noises may come from the flow of the refrigerant or the water line, Items stored on top of the icemaker can also make noises. The high efficiency compressor may make a pulsati
ページ13に含まれる内容の要旨
CLEANING AND MAINTENANCE The icemaker must be thoroughly cleaned if it has been left unused for a long time. Follow carefully any instructions provided for cleaning or use of sanitizing solution. Do not leave any solution inside the icemaker after cleaning. Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets,
ページ14に含まれる内容の要旨
Interior Cleaning The ice storage bin should be sanitized occasionally. Clean the water trough before the ice maker is used for the first time and reused after stopping for an extended period of time. It is usually convenient to sanitize the trough after the ice making system has been cleaned and the ice storage bin is empty. 1. Disconnect power to the unit. 2. Open the door and with a clean cloth wipe down the interior of the unit with a sanitizing solution made of 1 ounce of household b
ページ15に含まれる内容の要旨
3. Remove the slideway from the water sump. 4. Find the sprinkler arm and raise it. Disconnect it from the water tube which is connected at the back of the sprinkler arm. 5. A de-scaling solution can be prepared in a plastic basin with Nu- Calgon Nickel-Safe Ice Machine Cleaner. Mix 4 ounces of the ice machine cleaner per gallon of warm water. Remove the sprinkler arm from the interior. Thoroughly clean the sprinkler arm by soaking it in the basin
ページ16に含まれる内容の要旨
Condenser Cleaning A dirty or clogged condenser prevents proper airflow, reduces ice making capacity, and causes higher than recommended operating temperatures that may lead to component failure. Have the condenser cleaned at least once every six months. 1. Unplug the ice maker or disconnect power. 2. Remove the 2 screws at the bottom of the front cover and gently pull it off. 3. Locate the condenser filter. This can be lifted out and cleaned with a brush or flowing water. 4. Remove
ページ17に含まれる内容の要旨
Ice-making system Cleaning Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is or how effective your filtration may be. With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may need to clean the system as often as every 6 months. 1. Turn off the power to th
ページ18に含まれる内容の要旨
Control Panel (Inside of the front panel) Descriptions of LEDs and buttons: 1. Ice Full (Red) LED: Ice Full indicator light. When this LED is lit, the ice storage bin is full of ice or there is something obstructing the ice-full probe. The unit will stop working. When ice cubes are taken out of the ice storage bin, clearing the ice-full probe, the red LED will keep flashing for 3 minutes. Then the unit will restart and return to the ice making mode. 2. Ice Making (Green) LED: Ice Makin
ページ19に含まれる内容の要旨
TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section of this manual first. If the issue persists, check the troubleshooting section below. The issue could be solved by following the suggestions in the “Solution” column. Issue Possible Cause Solution The machine won't The icemaker is unplugged. Plug the ice maker in. operate. The fuse is blown. Replace fuse. The icemaker power switch is Turn the ice maker power sw
ページ20に含まれる内容の要旨
Specifications Description of product Full Size Ice Maker Full Size Ice Maker Full Size Ice Maker Model IB650SS IB1000SS IB1500SS Voltage/Frequency AC 115V~60Hz AC 115V~60Hz AC 115V~60Hz Ice-Making / Ice-Harvest 6.7A / 11.2A 7.3A / 11.7A 7.5A / 11.8A rated current Color Stainless Steel; Stainless Steel; Stainless Steel; Black Door Black Door Black Door Type of Ice Bullet Cube Bullet Ice Storage capacity 24 lbs maximum 35 lbs maximum 35 lbs maximum Ice-making capability 65 lbs / day
