ページ1に含まれる内容の要旨
AC-6000SB
TOOLBOX
Toolbox Installation Instructions 1
ページ2に含まれる内容の要旨
Introduction Congratulations on the purchase of your new toolbox! You can be assured your toolbox was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This installation manual was compiled for your benefit. Please read and follow the simple installation instructions described in this manual. The contents of this manual are based on the latest product information available at the time of pu
ページ3に含まれる内容の要旨
Table of Content SAFETY .................................................................................................................4-5 GENERAL SAFETY RULES....................................................................4-5 FUNCTIONAL DESCRIPTION ...............................................................................6 MODEL ....................................................................................................6 NAME OF PARTS ...................................
ページ4に含まれる内容の要旨
Safety RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A "DANGER, WARNING or CAUTION" safety warning will be surrounded by a "SAFETY ALERT BOX." This box is used to designate and emphasize Safety Warnings that must be fol- lowed when installing this toolbox. Accompanying the Safety Warnings are "signal w
ページ5に含まれる内容の要旨
CAUTION THIS INSTALLATION REQUIRES THE USE OF POWER TOOLS. SAFETY GLASSES SHOULD BE WORN AT ALL TIMES DURING THE USE OF THE POWER TOOLS. IF YOU ARE UNABLE TO LIFT A MINIMUM OF 75 LBS., THEN THIS INSTALLATION WILL RE- QUIRE THE USE OF TWO PEOPLE. PINCH AREA BETWEEN BODY AND LID OF TOOLBOX. Toolbox Installation Instructions 5
ページ6に含まれる内容の要旨
Functional Description MODEL: AC-6000SB NOTE: Some illustrations in this installation manual may show details that differ from those on your own toolbox. NAME OF PARTS: Side Mount Toolbox: Mounting Bracket (2) Mounting Bracket (2) Foam Tape (2) 1/4" Flat Washer (4) 3/8" Flat Washer (6) 1/4" x 1" Sheet Metal Screw (Black) (2) B l a c k 1/4" x 1" Sheet 3/8" x 1" Button 3/8" Locknut (6) Metal Screw (4) Head Screw (8) Plastic Plug (2) TB-Channel (6) TB-Divider
ページ7に含まれる内容の要旨
Installation INSTALLATION INSTRUCTIONS: CAUTION: IF YOU ARE UNABLE TO LIFT A MINIMUM OF 75 LBS., THEN THIS INSTALLATION WILL REQUIRE THE USE OF TWO PEOPLE. Use the pictures below as a guide in locating the side mount toolbox (A). Note: If the side mount toolbox (A) is to be installed with a front mount toolbox (As shown in Drawings B and C), be sure to leave enough space between the toolboxes to allow clearance to open both toolbox lids. A A B A C A Toolbox Ins
ページ8に含まれる内容の要旨
Installation INSTALLATION INSTRUCTIONS: CAUTION: THIS INSTALLATION REQUIRES THE USE OF POWER TOOLS. SAFETY GLASSES SHOULD BE WORN AT ALL TIMES DURING THE USE OF THE POWER TOOLS. CAUTION: PINCH AREA BETWEEN BODY AND LID OF TOOLBOX. (FIG. 1) 1. Peel backing off the foam tape. (Fig. 2) 2. Place foam tape (B) onto the bottom of the side mount toolbox (A) to protect the bed rail of the vehicle. (Fig. 3) (Fig.1) (Fig. 2) A B B (Fig. 3) 8 Toolbox Installation Instructi
ページ9に含まれる内容の要旨
Installation INSTALLATION INSTRUCTIONS (CONTINUED): CAUTION: SAFETY GLASSES SHOULD BE WORN DURING THIS STEP OF THE INSTALLATION. 4. Drill 3/16“ holes through the inside of the side mount toolbox (A) (Fig. 4) and the pickup truck bed rail according to the part number listed below: • 91 - Drill four holes through the bed rail. • 92 - Drill six holes through the bed rail. • 93 - Drill eight holes through the bed rail. Secure into position using 1/4 x 1“ sheet metal screws.
ページ10に含まれる内容の要旨
Installation INSTALLATION INSTRUCTIONS (CONTINUED): 5. Hold the side mount toolbox (A) level while positioning mounting brackets (B / C) as shown below. Once the side mount toolbox (A) is level and the mounting brackets (B /C) are in the desired position, use a pair of vise-grips to hold them together. Now use the existing holes in mounting bracket (B) as a guide to drill two 3/8“ holes through mounting bracket (C). Secure both mounting brackets (B / C) together using a 3/8 x
ページ11に含まれる内容の要旨
Installation INSTALLATION INSTRUCTIONS (CONTINUED): Optional Side Mount Toolbox - Divider installation instructions: 1. Peel the backing off of each piece of CO-Tape (B) and then place the CO-Tape pieces (B) onto the back of each TB-Channel (C) as shown below. Note: There are only three TB-Dividers (D) supplied with the side mount toolbox (A). 2. Now determine exactly where you would like to place the toolbox dividers. Mark out the locations for each TB-Channel (C) in the side mount tool
ページ12に含まれる内容の要旨
Maintenance MAINTENANCE INSTRUCTIONS: CLEANING INSTRUCTIONS: To maintain the luster of your toolbox, use a mild detergent. NOTE: Locks are provided as a deterrent to inadvertent opening or easy access to the contents of your toolbox. Contents stored in the toolbox are the responsibility of the user. LUBRICATION INSTRUCTIONS: All locks, latches, latching rods, and hinges should be lubricated regularly to assure smooth and proper operation for the life of the toolbox. Lubricate the fo
ページ13に含まれる内容の要旨
Maintenance MAINTENANCE INSTRUCTIONS (CONTINUED): TOOLBOX PUSH-BUTTON LATCH ASSEMBLY: L e v e r A s s e m b l y P u s h - B u t t o n L a t c h A s s e m b l y L u b r i c a t e TOOLBOX CATCH ASSEMBLY: Toolbox Installation Instructions 13
ページ14に含まれる内容の要旨
Notes 14 Toolbox Installation Instructions
ページ15に含まれる内容の要旨
Notes Toolbox Installation Instructions 15
ページ16に含まれる内容の要旨
Form #37-0826-071904 Manufactured for Deere & Company 16 Toolbox Installation Instructions ©Copyright 2004, John Deere Moline, Illinois 61265 John Deere Toolbox
