Aico Carbon Monoxide Alarm Ei 220ENの取扱説明書

デバイスAico Carbon Monoxide Alarm Ei 220ENの取扱説明書

デバイス: Aico Carbon Monoxide Alarm Ei 220EN
カテゴリ: 煙探知器
メーカー: Aico
サイズ: 0.16 MB
追加した日付: 1/24/2014
ページ数: 32
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスAico Carbon Monoxide Alarm Ei 220ENの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Aico Carbon Monoxide Alarm Ei 220ENに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Aico Carbon Monoxide Alarm Ei 220ENをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Aico Carbon Monoxide Alarm Ei 220ENのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Aico Carbon Monoxide Alarm Ei 220ENの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Aico Carbon Monoxide Alarm Ei 220EN 取扱説明書 - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Aico Carbon Monoxide Alarm Ei 220ENを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Aico Carbon Monoxide Alarm Ei 220ENの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

MAINS POWERED
CARBON MONOXIDE ALARM
- HARD WIRED TO MAINS
Model Ei 225EN
- WITH POWER CORD
Model Ei 220EN
Read and retain carefully for as long as the product is being used. It contains vital information
on the operation and installation. The leaflet should be regarded as part of the product.
If you are just installing the unit, the leaflet must be given to the householder. The leaflet is to
be given to any subsequent user.
INSTRUCTIONS
BS EN 50291: 2001
M MAI AINS NS
P PO OW WE ERED RED

ページ2に含まれる内容の要旨

Page CONTENTS 3 1 READ THIS FIRST 4 2 WHAT TO DO WHEN THE CO ALARM SOUNDS 3 CARBON MONOXIDE - THE SILENT KILLER! 5 11 4 WHERE TO PLACE CARBON MONOXIDE ALARMS 15 5 INSTALLING YOUR CARBON MONOXIDE ALARMS 19 6 TESTING YOUR CARBON MONOXIDE ALARMS 7 MAINTAINING CARBON MONOXIDE ALARMS 20 22 8 LIMITATIONS OF CARBON MONOXIDE ALARMS 24 9 HOW TO PROTECT YOUR FAMILY 10 TECHNICAL SPECIFICATIONS 26 28 11 GETTING YOUR CARBON MONOXIDE ALARMS SERVICED 28 12 GUARANTEE 13 TROUBLESHOOTING 30 2

ページ3に含まれる内容の要旨

1. READ THIS FIRST WARNING: The Ei225EN Alarm should be permanently wired to the mains by a qualified electrician in accordance with IEE wiring regulations (BS7671). The Ei220EN is just plugged in to the mains. Install the Carbon Monoxide Alarm (CO Alarm) in every room that contains a fuel burning appliance, particularly rooms where people spend a lot of time e.g. bedrooms, kitchens and sitting rooms. In rooms with an appliance install (preferably) on the ceiling, (300mm from walls), and between

ページ4に含まれる内容の要旨

When the CO Alarm detects abnormal levels of CO (above 50ppm CO) the red light starts to flash and the horn will sound within 90 minutes. At higher levels of CO the alarm will turn on sooner (see table B - page 9). The CO Alarm will automatically reset once the CO has cleared. Pressing the ? test/hush button resets the CO Alarm immediately (below 300ppm CO). If CO is still present the red light and horn will turn on again after about 4 minutes. The CO Alarm is no substitute for keeping chimneys

ページ5に含まれる内容の要旨

(5) Ring your gas or other fuel supplier on their emergency number. Keep the number in a prominent place. (6) Do not re-enter the property until the alarm has stopped. (If the alarm has been silenced by pressing the test/hush button, wait at least 5 minutes so the alarm can check that the CO has cleared). (7) Do not use the fuel appliances again until they have been checked by an expert. In the case of gas appliances this must be a CORGI registered installer. Figure 1 - Alarm Installation 3. CAR

ページ6に含まれる内容の要旨

(CO) poisoning. CO is an invisible, odourless, tasteless and extremely toxic gas. It is produced by appliances and vehicles burning fuels, such as coal, oil, natural/bottled gas, paraffin, wood, petrol, diesel, charcoal etc. CO is absorbed by red blood cells in the lungs in preference to oxygen - this results in rapid damage to the heart and brain from oxygen starvation. High levels of CO in a house can be caused by: • Incorrectly or poorly installed fuel-burning appliances. • Blocked or cracked

ページ7に含まれる内容の要旨

Mild Exposure: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms). Medium Exposure: Severe throbbing headache, drowsiness, confusion, fast heart rate. Extreme Exposure: Unconsciousness, convulsions, cardiorespiratory failure, death. A high level of CO for a short period (e.g. 350 ppm CO for 30 minutes) will cause the same symptoms, a slight headache, as a lower level for a longer time (e.g. 150 ppm for 90 minutes). Table A shows how exposure to different concentr

ページ8に含まれる内容の要旨

Table A: Effects of Carbon Monoxide Poisoning Concentration of CO in Air Inhalation Time (approx) and Symptoms Developed ppm 35 The maximum allowable concentration for continuous exposure in any 8 hour period according to OSHA *. 150 Slight headache after 1.5 hours. 200 Slight headache, fatigue, dizziness, nausea after 2-3 hours. 400 Frontal headaches within 1-2 hours, life threatening after 3 hours, also maximum parts per million in flue gas (on an air free basis) according to US Envi

ページ9に含まれる内容の要旨

Table B shows how the CO Alarm reacts to different levels of CO gas and exposure time. At higher levels of CO the alarm turns on sooner. The rate of flashing of the red light indicates the level of CO. Table B: CO Alarm Response CO Level Red Horn On ppm Alarm Light within 0 ppm Off * Off 50ppm 1 Flash / 2 Seconds 60 to 90 minutes 100 ppm 4 Flashes / 2 Second 10 to 40 minutes 300 ppm 8 Flashes / 2 Second 3 minutes * unless it has been in alarm (see CO Alarm Memory below) If your CO Alarm sounds

ページ10に含まれる内容の要旨

(Without this feature the CO level would need to be at 50ppm CO for 90 minutes for an indication to be given). Note the Pre-Alarm signal may be triggered by CO coming for example, from cooking with gas, from car engines or from nearby barbecues. This is usually not a concern unless the Pre-Alarm signal persists until the alarm sounds and the CO source is unknown. NOTE: The CO Alarm may sound if cigarette smoke is blown into it, or aerosols are released nearby. CO ALARM MEMORY - Red light is Off

ページ11に含まれる内容の要旨

4. WHERE TO PLACE CO ALARMS 3.1 Ideally a Carbon Monoxide Alarm should be installed in: - Every room containing a fuel burning appliance, and - Remote rooms where occupants spend a considerable amount of time - Every bedroom. However if the number of Carbon Monoxide Alarms is limited the following points should be considered when deciding where best to fit the alarm(s) - If there is an appliance in a room where people sleep, place a CO Alarm in this room and - Locate a CO alarm in a room contai

ページ12に含まれる内容の要旨

(2) Outside the building. (3) In an enclosed space (e.g. in or below a cupboard). (4) In a damp or humid area. (5) Directly above a sink or cooker. (6) Next to a door, window, air vent or anywhere that it would be affected by draughts. (7) Next to an extractor fan. (8) Where it would be obstructed, e.g. by curtains or furniture. (9) In an area where the temperature could drop below –10°C or rise above 40°C. (10) Where dirt or dust could block the sensor. (11) Where it could be easily knocked or

ページ13に含まれる内容の要旨

300mm 150mm 1 to 3 m DEAD AIR DON'T LOCATE 1 to 3 m HERE • The CO alarm should be a horizontal distance of between 1m and 3m from the potential CO source. • If there is a partition in the room, the CO alarm should be located on the same side of the partition as the potential source. • In rooms with sloped ceilings, the CO alarm should be located at the high side of the room (see fig 3). CO Alarm Figure 2. Location in room with a fuel burning appliance 13

ページ14に含まれる内容の要旨

300mm about 1 to 2m 3.31 If locating the CO alarm in a bedroom or in rooms remote from a fuel burning appliance (see figure 4) • Mount the CO alarm relatively close to the breathing zone of the occupants. Whatever position is chosen make sure it is possible to view the three light indicators, when in the vicinity of the alarm. CO Alarm CO Alarm Figure 3. Location in rooms with Figure 4. Location in bedroom & sloped ceilings, the CO alarm should rooms remote be located at the high side of the ro

ページ15に含まれる内容の要旨

5. INSTALLING YOUR CARBON MONOXIDE ALARMS The Alarm is designed to be permanently mounted. The unit can be screwed directly to the wall or ceiling and connected to the mains. It requires a current of 60mA. The Alarm must not be exposed to dripping or splashing. There are important markings on the underside of the alarm. IMPORTANT PRECAUTION: Do not install the actual alarm itself in new or renovated buildings until all work is completed (including floor coverings) and the building has been fully

ページ16に含まれる内容の要旨

INSTALLATION PROCEDURE Ei225EN (Only) Warning: The CO alarm should be installed by a qualified electrican in accordance with the IEE wiring regulations (BS 7671). Failure to install this alarm correctly may expose the user to shock or fire hazards. Procedure: 1. Select a location complying with the above advice. 2. Disconnect the AC mains supply from the circuit to be used. 3. Slide off the cover as shown in fig 1. Press gently in the centre to release the catches before sliding upwards. 4. R

ページ17に含まれる内容の要旨

6. The Brown wire (terminal 3) must be connected to the house wiring coloured brown or to a house terminal marked “L”. The Blue wire (terminal 4) must be connected to the house wiring coloured blue or to a house terminal marked “N”. The alarm does not need to be earthed, however for convenience a spare terminal (no. 5) is provided to hold an earth wire if present. 7. Turn on the mains power to the CO Alarm circuit. Figure 5 - Surface Wiring Figure 6 - Recessed Wiring Not Suitable Locations for

ページ18に含まれる内容の要旨

Ei220EN (Only) 1. Slide the cover off as shown in Figure 7 to expose the mounting screw holes. 2. Cut a notch in the back sidewall (on the centre of either side or at the bottom, for the power cord) to allow the unit to lie flush against the ceiling/wall. 3. Mark the two screw locations. Drill suitable holes (6mm drill) then insert the plastic anchors and screw the unit to the ceiling/wall. 4. Insert the plug into a suitable socket. Figure 7 Warning: Do not open (apart from the cover shown in fi

ページ19に含まれる内容の要旨

6. TESTING YOUR CO ALARM (1) Regularly check that the green mains power light is on. The unit cannot detect CO if the mains power is not on. (If it is off check circuit breakers, fuses, wiring etc). (2) Test the unit weekly by pressing the test/hush button. Hold the test button (for up to 10 seconds) until the horn sounds for over 5 seconds. This will help to familiarise you and your family with the distinctive on-off sound of the CO Alarm. This test checks that the electronics and horn are wo

ページ20に含まれる内容の要旨

inject the CO gas into the gas entry holes, see Figure 1. When it senses the CO it flashes the red light (as per Table B) to confirm that is detecting CO gas. How to distinguish between CO Alarm and Smoke Alarm Warnings The CO Alarm has a distinctive on-off sound of 3 pulses, followed by a pause as compared with a typical Smoke Alarm which has a rapid pulsing sound. In addition, when your CO Alarm is sounding, the red alarm light in the centre of the cover will be flashing. Testing both your CO


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Aico Ei166RC 取扱説明書 煙探知器 12
2 Aico Carbon Monoxide Alarm Ei 225EN 取扱説明書 煙探知器 40
3 Aico Ei161RC 取扱説明書 煙探知器 5
4 Aico Ei169RF 取扱説明書 煙探知器 1
5 Aico Ei168RC 取扱説明書 煙探知器 14
6 Aico Carbon Monoxide Alarms 260 Series 取扱説明書 煙探知器 0
7 Aico Ei164RC 取扱説明書 煙探知器 5
8 Aico Ei176RF 取扱説明書 煙探知器 1
9 Aico Residential Fire Detection RFD 取扱説明書 煙探知器 0
10 Aico 160 Series 取扱説明書 煙探知器 0
11 Adobe CS3 取扱説明書 煙探知器 1
12 ADT Security Services ADT-LCD40 取扱説明書 煙探知器 6
13 ADT Security Services Safewatch Pro 2000 取扱説明書 煙探知器 5
14 ADT Security Services SAVS20ADT-1 取扱説明書 煙探知器 3
15 ADT Security Services Unimode 9600 取扱説明書 煙探知器 7