ページ1に含まれる内容の要旨
K2566
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.co.uk
ページ2に含まれる内容の要旨
Consumer Information � Please read these instructions before assembly and use of this product. � Adult assembly is required. WARNING � Tool required for assembly: Phillips screwdriver (not included). To prevent serious injury or death: � Requires four “D” (LR20) alkaline batteries (not included) for operation. � Fall Hazard – It is dangerous to use � Product features and decorations may vary this reclined cradle on an elevated from photographs. surface, since child’s movement may �
ページ3に含まれる内容の要旨
Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Seat Back Tube Toy Bar 2 Retainers Pad Footrest with Soothing Unit Base Tube 2 Feet Left Base Wire Right Base Wire #8 x 1,9 cm Screw – 2 M5 x 20 mm Screw - 2 Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. 3
ページ4に含まれる内容の要旨
Battery Installation Assembly IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Hint: We recommend using alkaline batteries for DO NOT use if any parts are missing or broken. Contact Mattel for longer battery life. replacement parts and instructions if needed. Never substitute parts. Base Tube 1,5V x 4 “D” (LR20) Left Base Wire 1 Right Base Wire � Place the base tube on a flat surface. � Position the left and righ
ページ5に含まれる内容の要旨
Assembly Retainers Seat Back Tube Base Wire Base Wire 3 � Insert an M5 x 20 mm screw through each foot and tighten. Flex Base Wires Inward Pull Up Tabs 5 � Position the seat back tube above the base assembly. � Fit the seat back tube completely onto the base wires. 4 � Fit a retainer (rounded side inward) to one end of the seat back tube. � While flexing the base wires toward each other, hook the footrest onto the ends of the base wires. � Insert a #8 x 1,9 cm screw through the outs
ページ6に含まれる内容の要旨
Assembly Latch 6 Tab 7 � Fit the pad upper pocket onto the seat back tube. � Fit the pad lower pocket onto the footrest. � Fit the toy bar ends into the sockets in the footrest. Hint: The square end of the toy bar fits into the square socket and the circular end of the toy bar fits into the circular socket. � Make sure the toy bar latches are secure. The small tabs on the sockets should be visible in the opening in the latches. Assembly is now complete. 6
ページ7に含まれる内容の要旨
Setup and Use TIGHTEN Buckle Free End WARNING To prevent serious injury or death: � F all Hazard – It is dangerous to use this reclined cradle on an elevated surface, since child’s movement may Anchored End cause product to slide or tip over. Use only on a floor. LOOSEN Buckle � Suffocation Hazard – Never use on a soft surface (bed, sofa, cushion), since product can tip over and cause Free End suffocation in soft surfaces. � Always use the restraint system. � Never leave child unattende
ページ8に含まれる内容の要旨
Setup and Use Latch 5 Remove the Toy Bar � Pull the ends of the latches and lift the toy bar. Care The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, toy bar can be wiped clean using a mild cleaning solution and 4 damp cloth. Do not use bleach. Do not immerse the soothing unit or toy bar. Mode Switch Rainforest Sounds Volume Button or Music Switch Rainforest Sounds or Mu
