ページ1に含まれる内容の要旨
Please read this manual and save it with your
original sales receipt.
Tools needed for assembly: Phillips Screwdriver, Adjustable
Wrench (or Pliers) and Safety Scissors (all not included).
®
Use only with a Power Wheels 12 Volt Lead Acid
®
Rechargeable Battery and Power Wheels 12 Volt Charger
with Type 12V Connector (both included).
Requires four "C" (LR14) alkaline batteries for
FM Radio operation (not included).
Product features may vary from the picture above.
® ® ® ®
Jeep and the Jee
ページ2に含まれる内容の要旨
A T TABLE OF CONTENTS ABLE OF CONTENTS A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
WARNINGS AND CAUTIONS B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cau
ページ4に含まれる内容の要旨
C PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Windshield Vehicle Hood Steering
ページ5に含まれる内容の要旨
A TABLE OF CONTENTS PARTS C 1 #10 x / " Screw – 4 2 12 Volt Battery 12 Volt Charger #8 x 1" Screw – 7 #10 x 1" Screw – 11 Taillight Lens Set 3 #10 x / " Screw – 4 4 Taillight Housing Set 5 1 / " x 1 / " Pin - 1 32 2 #8 x4" Screw – 2 Lens Guard - 2 Headlight Lens - 2 #8-32 x 1.625" Screw – 2 #8 Acorn Lock Nut – 2 5 #8 x / " Screw – 1 8 Light Cover – 2 Hood Latch – 2 3 / " Washer – 1 8 #8 Lock Nut – 1 For your convenience, we included extra fasteners! Key Assembly Spacer - 2 Note: Tighten and lo
ページ6に含まれる内容の要旨
D A TABLE OF CONTENTS PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 22 14 20 13 18 25 16 13 21 26 10 9 6 8 7 17 11 4 3 12 8 24 3 19 1 23 15 2 5 1 Vehicle 11 Headlight Lens 21 Sport Bar Support - 2 Parts Not Shown 2 Steering Column 12 Lens Guard 22 Light Cover - 2 #8 x 1" Screw - 7 #8 Acorn Lock Nut - 2 3 Hood Latch 13 Short Seat Belt Strap 23 Door - 2 #10 x 1" Screw - 11 #8 Lock Nut - 1 1 3 4 12 Volt Battery 14 Windshield 24 Door Hinge - 2 #10 x /2" Screw
ページ7に含まれる内容の要旨
BATTERY CHARGING E ELECTRICAL HAZARD CAUTION WARNING • Battery can fall out and injure a child Use the charger in dry locations only. if vehicle tips over. Always use battery retainer. About Thermal Fuses • PREVENT FIRE Your Power Wheels 12 volt battery is equipped with a built-in - Never modify the electrical system. thermal fuse. The thermal fuse is a self-resetting safety device Alterations could cause a fire resulting which automatically “trips” and shuts down operation of the vehicl
ページ8に含まれる内容の要旨
E BATTERY CHARGING F ASSEMBLY Power WARNING Indicator Children can be harmed by small parts, sharp edges and sharp points in the vehicle's unassembled state, or by electrical items. B Care should be taken in unpacking and assembly of the vehicle. Children should not Battery handle parts, including the battery, or help in A assembly of the vehicle. B B A Charger B Connector Dash A A • Plug the charger connector into the battery . B • Plug the charger into a standard wall outlet . Notes:
ページ9に含まれる内容の要旨
ASSEMBLY F 12 5 5 Hole Steering Column 11 4 Bottom View 4 • Wipe the steering column with a paper towel to remove any excess lubricant. 2 • Turn the vehicle on its side. • Insert the straight end of the steering column up through the • Before applying the labels, wipe the surface of the vehicle with hole in the vehicle floor and out through the hole in the dash. a clean, dry cloth to remove any dust or oils. • While holding the steering column in place, turn the • Place the labels exactly a
ページ10に含まれる内容の要旨
F ASSEMBLY 5 1 / " x 1 / " Pin 32 2 End of Steering 5 " Column #8 x / Screw 8 End of Steering Column 6 #8 Lock Nut 5 1 • Insert the / " x 1 / " pin through the hole in the end of the 32 2 steering column. • Lower the steering column so that the pin fits inside the center of the steering wheel. 9 5 " • Insert a #8 x / screw through the hole in the end of the 8 Steering steering column. Wheel • Fit a #8 lock nut on the end of the screw and tighten. Cap • While holding the lock nut with an
ページ11に含まれる内容の要旨
ASSEMBLY F Slot Grille Tab Hood Slot Tabs Tab Slot Slot Front View 11 • Fit a lens assembly tab into the headlight slots in the grille. • Press firmly to snap the lens assembly into the grille. 13 • Repeat this procedure to snap the other lens assembly into the grille. • Insert the tabs on the hood into the slots in the front end of the vehicle. • Pull the hood forward and lower it closed. Hood Latch Windshield Slot Wipers Large Large Tab Tab Large Slots Hood Latch 12 Slot • Insert a hood
ページ12に含まれる内容の要旨
F ASSEMBLY Short Seat Belt Strap T-Loop (Pull through slot) Fastener End T-Loops Slot Seat Slot 17 15 Brush Guard • Turn the seat upside down. • Insert the fastener end of a short seat belt strap through the slot • Fit and hold the brush guard against the front end of the vehicle. near the outer edge of the seat. Make sure the side of the seat belt with the fastener faces the outer edge of the seat. Hint: Using the end of a Phillips screwdriver, poke a hole in the thin, plastic covering ov
ページ13に含まれる内容の要旨
ASSEMBLY F Sport Bar Seat Seat Back Tabs Tabs PUSH B HERE C Slot Supports A Side View 19 21 • With the seat at an angle, insert the tabs on the front edge of A the seat into the slots in the foot-well wall . • Fit a support to one side of the sport bar. • Push down firmly on the edge of the seat above each tab to " • Insert a #8- 32 x 1.625 screw through the support, the sport B snap the tabs into the slots . bar and out through the support. C • Rotate the back of the seat down to snap th
ページ14に含まれる内容の要旨
F ASSEMBLY Taillight Housing Sport Bar Support PUSH HERE Side Fender Taillight Lens #8 x 1" Screws PULL HERE Back View 25 • Turn the vehicle upright. Side View 23 • Using safety scissors, remove the taillight lenses and the taillight housings from the plastic connectors. Dispose of the • Fit the sport bar assembly into the holes in the top side of plastic connectors. the vehicle. • Face the rear of the vehicle. • Push down firmly on a sport bar support while pulling up on • Fit a tailli
ページ15に含まれる内容の要旨
ASSEMBLY F Loosen These Door Screws Battery Compartment 28 Door • Locate the FM Radio on the dash. • Loosen both screws in the battery compartment door. • Remove the battery compartment door. • Insert four , new "C" (LR14) alkaline batteries. Hint: We recommend using alkaline batteries for longer life. Side View 26 • Replace the battery compartment door and tighten the screws. • When sounds become faint or stop, it’s time for an adult to change the batteries! Please refer to page 22 for gene
ページ16に含まれる内容の要旨
G A TABLE OF CONTENTS DECORATION Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: • Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. • For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a labe
ページ17に含まれる内容の要旨
DECORATION G 20 20 10 8 18 1 6 FRONT LEFT SIDE 8 9 13 2 6 FRONT RIGHT SIDE H4807pr-0922 17 H4807pr-0922
ページ18に含まれる内容の要旨
H BATTERY INSTALLATION ® IMPORTANT! Use only a Power Wheels 12 volt battery. Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 hours using the enclosed ® Power Wheels 12 volt charger before operating your vehicle Motor Harness for the first time. Charge the battery for at least 14 hours after Connector each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instructions may damage your batter
ページ19に含まれる内容の要旨
BATTERY CARE AND DISPOSAL I Disposal Care If a battery leak develops, avoid contact with the leaking acid ® • Your Power Wheels battery is sealed lead-acid battery. and place the damaged battery in a plastic bag. See information They must be recycled or disposed of in an environmentally below for proper disposal. sound manner. If acid comes in contact with skin or eyes, flush with cool • Do not dispose of a lead-acid battery in a fire. The battery may water for at least 15 minutes and call
ページ20に含まれる内容の要旨
J SAFE DRIVING RULES Teach Safety Rules to Children RIDING HAZARD While children can quickly develop the skill necessary to drive this vehicle, it is important to remember that their judgment skills are WARNING still very immature. Unsupervised driving by children can lead to serious injury. Before children use this vehicle, an adult should • Prevent Injuries and Deaths carefully evaluate the driving area as well as the children’s skill level and ability to drive this vehicle safely. Child
