ページ1に含まれる内容の要旨
MODEL G0514X, G0514X2,
G0514X2B, & G0514X3
EXTREME SERIES BANDSAW
OWNER'S MANUAL
(For models manufactured since 2/12)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
ページ2に含まれる内容の要旨
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
ページ3に含まれる内容の要旨
Table of Contents INTRODUCTION ............................................... 2 SECTION 1: SAFETY ....................................... 7 SECTION 5: ACCESSORIES ......................... 50 SECTION 2: POWER SUPPLY ...................... 10 SECTION 6: MAINTENANCE ......................... 52 SECTION 3: SETUP ....................................... 14 SECTION 7: SERVICE ...................
ページ4に含まれる内容の要旨
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual For Your Own Safety, Read Instruction Manual Before Operating Bandsaw a) Wear eye protection. b) Do not remove jammed cutoff pieces until blade has stopped. c) Maintain proper adjustment of blade te
ページ5に含まれる内容の要旨
Identification (G0514X) Figure 1. Figure 2. A. S. B. T. C. M. D. N. E. O. F. P. G. Q. H. R. I. S. J. T. K. V. L. U.
ページ6に含まれる内容の要旨
Identification (G0514X2/G0514X2B/G0514X3) Figure 4. Figure 5. L. M. Figure 3. N. O. A. P. B. Q. C. R. D. S. E. T. F. U. G. V. H. W. I. X. J. Y. K.
ページ7に含まれる内容の要旨
MODEL G0514X, G0514X2, G0514X2B, G0514X3 19" 3 HP EXTREME SERIES BANDSAW Model Number G0514X G0514X2 G0514X2B G0514X3
ページ8に含まれる内容の要旨
Model Number G0514X G0514X2 G0514X2B G0514X3
ページ9に含まれる内容の要旨
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
ページ10に含まれる内容の要旨
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
ページ11に含まれる内容の要旨
Additional Safety for Bandsaws BLADE CONDITION. CUTTING TECHNIQUES. BLADE REPLACEMENT. HAND PLACEMENT. SMALL WORKPIECE HANDLING. FEED RATE. BLADE SPEED. WORKPIECE MATERIAL. WORKPIECE SUPPORT. BLADE CONTROL.
ページ12に含まれる内容の要旨
SECTION 2: POWER SUPPLY Availability Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual. Circuit Information Electrocution, fire, or equipment damage may occur if machine is not correctly grounded and connected to the power supply. For your own safety and protection of
ページ13に含まれる内容の要旨
G0514X, G0514X2, G0514X2B Grounding Requirements For 220V operation: No adapter should be used with the required plug. If the plug does not fit the available receptacle, or the machine must be reconnected for use on a different type of circuit, the reconnection must be made by a qualified electrician and comply with all local codes and ordinances. GRO
ページ14に含まれる内容の要旨
G0514X3 Circuit Requirements 220V Figure Nominal Voltage Range ................. 220V–240V Cycle ..........................................................60 Hz Phase .................................................... 3-Phase Power Supply Circuit ......................... 15 Amps Connection Type..Locking Disconnect Switch G0514X3 Circuit Requirements 440V Voltage Conversion Nominal Volt
ページ15に含まれる内容の要旨
3. G0514X3 440V G0514X3 Wiring Diagram Page 72. Conversion 4. Note: The reference motor wiring diagram on Page 72 was current at the time of printing, but always use the wiring diagram provided inside the motor junction box, as it will reflect any changes to the motor shipped with your machine. To rewire the Model G0514X3 for 440V opera- tion: 1. 2. Figure 9 Figure 9.
ページ16に含まれる内容の要旨
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Get lifting help or use Unpacking power lifting equipment such as a forklift to move heavy ite
ページ17に含まれる内容の要旨
G0514X Inventory Crate Contents (Figure 10 & 11 Qty A. Figure 10. B. C. D. E. F. G. Hardware and Tools (not shown): Qty Figure 11. NOTICE If you cannot find an item on this list, care- fully check the machine and the packaging materials. Some of these items may be pre- installed for shipping or become misplaced during unpacking.
ページ18に含まれる内容の要旨
G0514X2 & G0514X3 Inventory Figure 12. Crate Contents (Figure 12–14 Qty A. B. C. D. E. F. G. H. I. J. Hardware and Tools (not shown): Qty Figure 13. Figure 14 NOTICE If you cannot find an item on this list, care- fully check the machine and the packaging materials. Some of these items may be pre- installed for shipping or become misplaced
ページ19に含まれる内容の要旨
G0514X2B Crate Contents (Figure 15–17 Qty A. Figure 15. B. C. D. E. F. G. H. I. J. K. Hardware and Tools (not shown): Qty Figure 16. Figure 17
ページ20に含まれる内容の要旨
Hardware Recognition Chart
