ページ1に含まれる内容の要旨
IM10066
®
November, 2010
AIR VANTAGE 500 (AU)
For use with machine having Code Number: 11656
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ-
ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT. And,
most importantly, think before
you act and be care
ページ2に含まれる内容の要旨
i i SAFETY WARNING CALIFORNIA PROPOSITION 65 WARNINGS Diesel engine exhaust and some of its constituents The engine exhaust from this product contains are known to the State of California to cause can- chemicals known to the State of California to cause cer, birth defects, and other reproductive harm. cancer, birth defects, or other reproductive harm. The Above For Gasoline Engines The Above For Diesel Engines ARC WELDING CAN bE HAzARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIbLE SERIOUS INJURY
ページ3に含まれる内容の要旨
ii ii SAFETY ARC RAYS can burn. ELECTRIC SHOCK can 4.a. Use a shield with the proper filter and cover kill. plates to protect your eyes from sparks and 3.a. The electrode and work (or ground) circuits the rays of the arc when welding or observing are electrically “hot” when the welder is on. open arc welding. Headshield and filter lens Do not touch these “hot” parts with your bare should conform to ANSI Z87. I standards. skin or wet clothing. Wear dry, hole-free gloves to insulate hands. 4.b. Us
ページ4に含まれる内容の要旨
iii iii SAFETY WELDING and CUTTING CYLINDER may explode SPARKS can if damaged. cause fire or explosion. 7.a. Use only compressed gas cylinders 6.a. Remove fire hazards from the welding area. containing the correct shielding gas for the If this is not possible, cover them to prevent process used and properly operating the welding sparks from starting a fire. regulators designed for the gas and Remember that welding sparks and hot pressure used. All hoses, fittings, etc. should be suitable for mat
ページ5に含まれる内容の要旨
iv iv SAFETY PRÉCAUTIONS DE SÛRETÉ 6. Eloigner les matériaux inflammables ou les recouvrir afin de prévenir tout risque d’incendie dû aux étincelles. Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce 7. Quand on ne soude pas, poser la pince à une endroit isolé de manuel aussi bien que les précautions de sûreté générales suiv- la masse. Un court-circuit accidental peut provoquer un antes: échauffement et un risqu
ページ6に含まれる内容の要旨
v v SAFETY Electromagnetic Compatibility (EMC) Conformance Products displaying the CE mark are in conformity with European Community Council Directive of 15 Dec 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility, 2004/108/EC. It was manufactured in conformity with a national standard that implements a harmonized standard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It is for use with other Lincoln E
ページ7に含まれる内容の要旨
vi vi SAFETY Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises. Methods of Reducing Emissions Mains Supply Welding equipment should be connected to the mains supply according to the manufacturer’s recommenda- tions. If interference occurs, it may be necessary to take additional precautions such as filter
ページ8に含まれる内容の要旨
vii vii for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product Thank You ••• as much pride as we have in bringing this product to you! CUSTOMER ASSISTANCE POLICY The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip- ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask L
ページ9に含まれる内容の要旨
viii viii TAbLE OF CONTENTS Page Installation.......................................................................................................................Section A Technical Specifications.......................................................................................................A-1 Safety Precautions ........................................................................................................A-2 Location and Ventilation...........................................
ページ10に含まれる内容の要旨
ix ix TAbLE OF CONTENTS Accessories........................................................................................................Section c Optional Field Installed Accessories......................................................................C-1 ________________________________________________________________________ Maintenance.......................................................................................................Section D Safety Precautions .........................
ページ11に含まれる内容の要旨
A-1 A-1 INSTALLATION TECHNICAL SPECIFICATIONS - AIR VANTAGE® 500 (AU) (K32012-1) INPUT - DIESEL ENGINE Make/Model Description Speed (RPM) Displacement Starting Capacities cu. in. (ltrs.) System 4 cylinder High Idle 1900 199(3.3) 12VDC Battery & Fuel: 25 gal. Cummins 56 HP (42kw) starter (94.6 L) B3.3 1800 RPM Full Load 1800 Bore x Stroke inch (mm) Oil: 2 gal. (7.5L) Diesel Engine Low Idle 1425 3.74 X 4.53 Radiator Coolant: (95 x 115mm) 2.6gal. (9.8L) RATED OUTPUT @ 104°F(40°
ページ12に含まれる内容の要旨
A-2 A-2 INSTALLATION SAFETY PRECAUTIONS LOCATION AND VENTILATION WARNING The welder should be located to provide an unrestrict- ed flow of clean, cool air to the cooling air inlets and to Do not attempt to use this equipment until you avoid restricting the cooling air outlets. Also, locate have thoroughly read the engine manufacturer’s the welder so that the engine exhaust fumes are prop- manual supplied with your welder. It includes erly vented to an outside area. important safety precaution
ページ13に含まれる内容の要旨
A-3 A-3 INSTALLATION TOWING LIFTING The recommended trailer for use with this equipment The AIR VANTAGE® 500 (AU) lift bale should be used (1) for road, in-plant and yard towing by a vehicle is to lift the machine. The Air Vantage 500 is shipped Lincoln’s K2636-1. If the user adapts a non-Lincoln with the lift bale retracted. Before attempting to lift the trailer, he must assume responsibility that the method AIR VANTAGE® 500 (AU) the lift bale must be secured of attachment and usage does not
ページ14に含まれる内容の要旨
A-4 A-4 INSTALLATION PRE-OPERATION ENGINE AND COM- ENGINE COOLANT PRESSOR SERVICE WARNING READ the engine and compressor operating and maintenance instructions supplied with this machine. HOT COOLANT can burn skin. •Do not remove cap if radiator is hot. WARNING • Keep hands away from the engine ------------------------------------------------------------------------ muffler or HOT engine parts. The welder is shipped with the engine and radiator • Stop engine and allow to cool before filled wi
ページ15に含まれる内容の要旨
A-5 A-5 INSTALLATION The AIR VANTAGE® 500 (AU) is shipped with the Listed in Table A.1 are copper cable sizes recom- negative battery cable disconnected. Before you oper- mended for the rated current and duty cycle. Lengths ate the machine, make sure the Engine Switch is in stipulated are the distance from the welder to work the OFF position and attach the disconnected cable and back to the welder again. Cable sizes are securely to the negative (-) battery terminal. increased for greater leng
ページ16に含まれる内容の要旨
A-6 A-6 INSTALLATION REMOTE CONTROL STANDbY POWER CONNECTIONS The AIR VANTAGE® 500 (AU) is equipped with a 6- pin and a 14-pin connector. The 6-pin connector is for The AIR VANTAGE® 500 (AU) is suitable for tempo- connecting the K857 or K857-1 Remote Control or for rary, standby or emergency power using the engine TIG welding, the K870 foot Amptrol or the K963-3 manufacturer’s recommended maintenance schedule. hand Amptrol. When in the CC-STICK or CV-WIRE modes and when a remote control is co
ページ17に含まれる内容の要旨
A-7 A-7 INSTALLATION CONNECTION OF LINCOLN ELEC- • Set the "WELD TERMINALS" switch to "WELD TRIC WIRE FEEDERS TERMINALS ON". WARNING • When the gun trigger is closed, the current sens- ing circuit will cause the AIR VANTAGE® 500 Shut off welder before making any electrical con- (AU) engine to go to the high idle speed, the wire nections. will begin to feed and the welding process start- ed. When welding is stopped, the engine will --------------------------------------------------------------
ページ18に含まれる内容の要旨
A-8 A-8 INSTALLATION CONNECTION OF THE LN-25 TO THE AIR CONNECTION OF AN NA-3 AUTOMATIC VANTAGE® 500 (AU). WELDING SYSTEM TO THE AIR VAN- TAGE® 500 (AU) WARNING For connection diagrams and instructions for connect- ing an NA-3 Welding System to the AIR VANTAGE® Shut off welder before making any electrical con- 500 (AU), refer to the NA-3 Welding System instruc- nections. tion manual. The connection diagram for the LN-8 can ----------------------------------------------------------------------
ページ19に含まれる内容の要旨
b-1 b-1 OPERATION RECOMMENDED APPLICATIONS SAFETY PRECAUTIONS The AIR VANTAGE® 500 (AU) provides excellent con- Read and understand this entire section before stant current DC welding output for stick (SMAW) and operating your AIR VANTAGE® 500 (AU). TIG welding. The AIR VANTAGE® 500 (AU) also pro- vides excellent constant voltage DC welding output for WARNING MIG (GMAW), Innershield (FCAW), Outershield (FCAW-G) and Metal Core welding. In addition the AIR VANTAGE® 500 (AU) can be used for Arc Do
ページ20に含まれる内容の要旨
b-2 b-2 OPERATION CONTROLS AND SETTINGS All welder and engine controls are located on the case front panel. Refer to Figure B.1 and the explanations that follow. FIGURE b.1 1 1 1 1 1 1 1 2 2 2 1 4 6 5 3 3 3 3 9 7 8 1 01 0 2 12 4 5 6 7 33 2 1 2 11 2 2 2 2 2 2 2 9 8 3 5 0 6 7 8 9 4 2 1 3 8 6 12 4 5 7 33 9 14 10 13 11 16 25 15 21 24 21 26 19 27 2 28 1 22 17 3 18 23 20 29 30 31 32 ENGINE CONTROLS (Items 1 through 9) 4. HOUR METER 1. RUN STOP SWITCH The hour meter displays the t
