ページ1に含まれる内容の要旨
Angle Sander
MODEL 9060DBL
001015
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ページ2に含まれる内容の要旨
SPECIFICATIONS Model 9060DBL No load speed (RPM) 6,000/min Overall length 458 mm (18”) Net weight 4.2 kg (9.3 lbs) Spindle thread 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work
ページ3に含まれる内容の要旨
5. Avoid body contact with grounded sur- be used for appropriate conditions. Ordinary faces such as pipes, radiators, ranges and eye or sun glasses are NOT eye protection. refrigerators. There is an increased risk of Tool Use and Care electric shock if your body is grounded. 15. Use clamps or other practical way to 6. Do not expose power tools to rain or wet secure and support the workpiece to a conditions. Water entering a power tool will stable platform. Holding the work by hand or increase th
ページ4に含まれる内容の要旨
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
ページ5に含まれる内容の要旨
9. Make sure the abrasive disc or the wheel IF USED AS A GRINDER is not contacting the workpiece before the 16. Always use proper guard with grinding switch is turned on. wheel. A guard protects operator from bro- 10. Watch out for flying sparks. Hold the tool ken wheel fragments. so that sparks fly away from you and other 17. When using depressed center grinding persons or flammable materials. wheels, be sure to use only fiberglass- 11. Do not leave the tool running. Operate the reinforced whee
ページ6に含まれる内容の要旨
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001026 Shaft lock CAUTION: 1 • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock 001041 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns t
ページ7に含まれる内容の要旨
001112 Installing or removing abrasive disc 1 (optional accessory) 2 NOTE: 3 • Use sander accessories specified in this manual. These must be purchased separately. Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the lock nut onto the spindle. To 1. Lock nut tighten the lock nut, press the shaft lock firmly so that the 2. Abrasive disc 3. Rubber pad spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. 001089 To remove the disc, foll
ページ8に含まれる内容の要旨
001064 Installing or removing wheel guard 1 CAUTION: • When using a depressed center grinding wheel/Multi- disc, flex wheel or wire wheel brush, the wheel guard must be fitted on the tool so that the closed side of the 3 guard always points toward the operator. 2 Mount the wheel guard with the protrusion on the wheel 1. Wheel guard guard band aligned with the notch on the bearing box. Then 2. Bearing box rotate the wheel guard around 180 degrees. Be sure to 3. Screw tighten the screw securely. T
ページ9に含まれる内容の要旨
001101 Installing or removing flex wheel 1 (optional accessory) 2 3 WARNING: 4 • Always use specific guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. 1. Lock nut Follow instructions for depressed center grinding wheel/ 2. Flex wheel 3. Plastic pad Multi-disc but also use plastic pad over wheel. See order of 4. Inner flange assembly on accessories page in this manual. 001089 1 2 1. Lock nut wrench
ページ10に含まれる内容の要旨
ALWAYS hold the tool firmly with one hand on rear handle and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction. 001141
ページ11に含まれる内容の要旨
• ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injury. Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pres- sure which causes over bending of wires, leading to prema- ture breakage. MAINTENANCE 001170 CA
ページ12に含まれる内容の要旨
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. • If you decide to use your Makita sander with approved accessories which you purchase from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in th
ページ13に含まれる内容の要旨
001188 1 2 2 8 2 12 3 3 9 11 13 4 6 10 5 7 5 C00169 9060DBL 1 Grip 36 2 Wheel guard 3 Inner flange 89 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 5/8-40 6 Plastic pad 7Flex wheel 8 Rubber pad 170 9 Abrasive disc 10 Sanding lock nut 5/8-48 11 Wire wheel brush 12 Urethane washer 14 13 Wire cup brush - Lock nut wrench 28 - Accessory kit 7” or 9” 13
ページ14に含まれる内容の要旨
Memo 14
ページ15に含まれる内容の要旨
Memo 15
ページ16に含まれる内容の要旨
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
