ページ9に含まれる内容の要旨
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool-specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bull point Cold chisel 410 mm (16-118”) 36 mm (1-318”) x 410 mm (16-118“) Part No. 751407-0 Part No. 751207-8 Scaling chisel Clay spade 100 mm (4“) x 310 mm (12-114”) 120 mm (4-314“) x 5
ページ10に含まれる内容の要旨
July-16-'84 US DEMOLITION HAMMER Model HM1301 Note: The switch and other part configurations may differ from country to country. 10
ページ11に含まれる内容の要旨
MODEL HM1301 Nov-09-'84 US ""0" SD DESCRIPTION At, DESCRIPTION MACHINE MACHINE ~ ~ 1 2 Hex Socket Head Bolt M6x16 54 6 Hex 0011 M5x14 (With Washer) 2 2 Spring Washer 6 55 1 011 Tank Cover 3 I Rear Cover 56 1 081 Tank Packing 57 1 4 1 Motor Housing Compression Spring 4 5 1 CORD ASSEMBLY 58 1 Steel Ball 4 8 IAssembled Cord Plug & Item 61 59 1 Plunger 6 1 Cord Guard 60 2 Pan Head Screw M4x14 IWith Washer) 61 1 7 1 Pan Head Screw M4~18 (With Washer1 Tool Retainer 8 1 Strain Relief 62
ページ12に含まれる内容の要旨
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or mater
ページ1に含まれる内容の要旨
Demolition Hammer
MODEL HM1301
INSTRUCTION MANUAL
SPEC1 F ICATIONS
Blows per minute Overall length Net weight
I
1,200
643 mm (25-5/16") 16.3 kg (36 Ibs)
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp lit. Don't expose power tools to rain. or wet locations. Keep work area well Don't use tool in presen
ページ3に含まれる内容の要旨
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turn- ing it on, 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't oper- ate tool when you a
ページ4に含まれる内容の要旨
For all grounded tools with American type plug. GROUNDING INSTRUCTIONS: Thistool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a threetonductor cord and three-prong grounding- to fit the proper grounding-type receptacle. The green (or green and yellow) conductor type plug in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal. Your unit is for use on 115 volts and has a plug that look
ページ5に含まれる内容の要旨
0 Installing or removing'hull point or other bits (cold chisel, etc.) CAUTION : Always be sure that the tool is switched off and unplugged before installing or remov- ing the bit. Pull out and turn the tool retainer so that the boss on the tool retainer faces in the direction of the arrow. Insert the bit into the tool holder as far as it will go. Then turn the tool retainer 180 degrees to secure the bit. To remove the bit, follow the installation procedure in reverse. Fig. 1 Fig. :
ページ6に含まれる内容の要旨
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. Trigger switch Fig. 1 CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the “OFF” position when released. Demolishing . Chipping - Scaling Choose the right accessories for your work. After mounting the suitable acces- sory and switching on the demolition hammer, let the mere weight of the tool itself apply pressure to the work surfa
ページ7に含まれる内容の要旨
MAINTENANCE CAUTION : ALWAYS be sure that the tool is switched off and unplugged before attempting to per- form inspection and maintenance. e Oiling Oiling should be performed every three hours (once a day before use). Hold the tool vertically and pull the lubrication knob three to five times. Oil in the tank should be replenished about every 20 days, presuming 3 - 4 hours’ operation daily, or when oil is out of sight through the window after placing the tool ver- tically. Fig. 6
ページ8に含まれる内容の要旨
Use the screwdriver to remove the screw holding the holder cap plate as shown in the figure. Fig. 9 Use the screwdriver to remove the brush holder cap as shown in the figure. Take out the worn brush, insert the new one and secure the brush holder cap. Fig. 1 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 8
