ページ1に含まれる内容の要旨
Operating and Installation
Instructions
Built-in Plate Warmer
EGW 2062
To prevent accidents and en - US, CA
appliance damage read
these instructions
before
installation or use. M.-Nr. 07 342 340
ページ2に含まれる内容の要旨
2
ページ3に含まれる内容の要旨
Contents IMPORTANT SAFETY INSTRUCTIONS.................................4 Guide to the machine ..............................................7 Before using for the first time........................................8 Using the plate warmer.............................................9 Cleaning and care ................................................12 Frequently asked questions........................................13 Technical Service.................................................14 IMPORTANT
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Correct usage WARNING- When using your This appliance is intended for appliance follow basic residential use only. Only use the precautions, including the appliance for its intended purpose as following: described in this manual. Other uses are not permitted and can Read all instructions before be dangerous. installation or use to prevent injury and appliance damage. Persons who lack physical, sensory or mental abilities, or experience with This appliance confor
ページ5に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Technical safety Hardwiring the appliance should be performed by a certified electrician in Before installing the appliance, compliance with all local and national check for externally visible damage. codes, and requirements. Do not operate a damaged appliance. Do not operate any appliance with a Be certain your appliance is damaged cord or plug, or if the properly installed and grounded by a appliance has been damaged in any qualified technician. To guarant
ページ6に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Safety Do not use a steam cleaner to clean this appliance. Steam could penetrate The plate warmer interior, the top in electrical components and cause a particular, gets very hot when in use short circuit. Pressurized steam may and remains hot for some time once cause permanent damage to the turned off. Use caution. surface and to components of the Protect your hands with oven mitts appliance. or potholders when using the To prevent injuries, do not use appl
ページ7に含まれる内容の要旨
Guide to the machine On/Off button (lights up) Temperature selector Warming drawer Non-slip mat Indicator Warning sticker to indicate burn hazard 7
ページ8に含まれる内容の要旨
Before using for the first time Clean the appliance Heat the appliance Remove any protective wrapping. Heat the empty plate warmer for a minimum of 2 hours. Turn the Remove the non-slip mat and clean temperature selector to "Maximum" with a solution of warm water and (see "Selecting a temperature"). liquid dish soap. Dry with a soft cloth. Vent the room when heating the Clean the plate warmer, inside and drawer for the first time. out, with a damp cloth and wipe dry. Metal components h
ページ9に含まれる内容の要旨
Using the plate warmer The plate warmer is only intended for warming dishes. Do not use the plate warmer to reheat, cook or keep food and drinks warm. Condensation from food or drinks could cause moisture damage to the appliance. Use pot holders when removing dishes. The drawer can hold a maximum of 33 lbs (15 kg). Opening and Closing To open and close the plate warmer gently push the center of the drawer. Controls The controls include the temperature selector and the On/Off button. They are onl
ページ10に含まれる内容の要旨
Using the plate warmer Operating Place the dishes in the plate warmer. Select a temperature. Turn the appliance on (). The On/Off button will light. Close the drawer. The indicator at the front of the appliance drawer lights showing that the unit is on. Turn the appliance off (), before removing the warmed dishes. Pull the drawer out all the way to remove the dishes. Selecting a temperature The temperature selector allows you to select a temperature between 86° and 122°F (30° and
ページ11に含まれる内容の要旨
Using the plate warmer Warming times Various factors will affect the warming times: – type and thickness of the dishes, – quantity, – how the dishes are arranged, and – the temperature setting. As you use the plate warmer you will learn which settings suit your needs best. As a guideline: It will take approx. 30 - 40 minutes to evenly warm dishes at the maximum temperature setting of 122°F (50°C). Capacity The quantity which can be loaded will depend on the size of your dishes. Example: – 25 Cap
ページ12に含まれる内容の要旨
Cleaning and care To better maintain your appliance Allow the appliance to cool before avoid the following: cleaning. – cleaners containing soda, ammonia, thinners, or chlorides Do not use a steam cleaner to clean this appliance. Pressurized steam – cleaners containing descaling could penetrate electrical agents, components and cause a short – abrasive cleaners, circuit. – stainless steel cleaners, Do not use commercial cleaning – dishwasher soap (powder), agents. Only use agents – caustic (oven
ページ13に含まれる内容の要旨
Frequently asked questions Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. The dishes are not warm enough. Possible fault Solution The appliance is turned off. Turn the appliance on with the On/Off button. The wrong temperature was selected. Check the temperature setting. The dishes need more time to warm. Increase the timer setting. See "Warming times". The dish
ページ14に含まれる内容の要旨
Technical Service In the event of a fault which you cannot MieleCare easily fix yourself, please contact the (USA only) Miele Technical Service Department at the address on the back of this booklet. MieleCare, our Extended Service Contract program; gives you the When contacting Technical Service assurance of knowing that your please quote the serial number and appliance investment is covered by 5 model of the appliance. This years of worry free ownership. information is visible on the silver dat
ページ15に含まれる内容の要旨
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and appliance damage read these instructions before installation or use.
ページ16に含まれる内容の要旨
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Before installation make sure that To install the combination appliance the voltage and frequency listed on the please see the manual supplied with data plate correspond with the that machine. household electrical supply. This data This appliance is not designed for must correspond in order to avoid risk maritime use or for use in mobile of damage to the appliance. If in doubt, installations such as recreational consult a qualified technician. veh
ページ17に含まれる内容の要旨
Installation Installation dimensions Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Combination with Coffee system * Machine with glass front ** Machine with stainless steel front 17
ページ18に含まれる内容の要旨
Installation Installing the appliance Set the plate warmer into the niche, push is all the way in. Be sure that is it aligned it at a right angle. Open the drawer and fix the appliance with the two supplied screws at the side panels of the cabinet. Install the combination appliance regarding the manual supplied with that machine. 18
ページ19に含まれる内容の要旨
Installation Aligning the appliance front After installing the combination appliance it may be necessary to align the appliance front and/or even the gap between the plate warmer and the combination machine. Flat washers are supplied beneath the knurled nuts, which fix the drawer to the telescopic runners. Loosen the knurled nuts and take the drawer out. Align and even the gap with the flat washers by changing their position (above or below the drawer), on both sides. 19
ページ20に含まれる内容の要旨
Electrical connection Power supply CAUTION: Before servicing, This appliance is equipped witha5ft disconnect the power supply by (1.5 m) long power cord with a either removing the fuse, shutting off three-prong grounding plug ready for the power main or manually connection to a 120 V, 15 A, 60 Hz "tripping" the circuit breaker. power supply. Installation work and repairs should Further installation details are on the only be performed by a qualified wiring diagram. technician in accordance with
