ページ1に含まれる内容の要旨
PoE Splitter
Power over Ethernet Splitter
802.3af
PN: POE-22001T
USER’S MANUAL
ページ2に含まれる内容の要旨
Content Overview ...........................................................1 Features............................................................1 Hardware Description......................................2 Package Contents............................................2 Installation ........................................................5 Technical Specification ...................................6
ページ3に含まれる内容の要旨
Overview Unicom's new Power over Ethernet (PoE) Splitter Adapter provides Ethernet data and DC power to a network device that is not compliant with the IEEE802.3af standard (non-PoE). This adapter effectively provides Ethernet data and DC power to a non-PoE device with a single cable and allows it to operate within a PoE network. PoE is an efficient and convenient solution for remote applications where available space is limited and/or no power source is readily available. Following is a sample
ページ4に含まれる内容の要旨
Package Contents (1) Power over Ethernet Splitter (2) DC Power Cables – 5.5x2.0mm and 5.5x2.5mm User's Manual PoE Splitter DC Power Cables User's Manual With adjustable output Figure 1-1. Package Contents Compare the contents of your Power over Ethernet Splitter package with the standard checklist above. If any item is missing or damaged, please contact your local dealer for service.
ページ5に含まれる内容の要旨
Hardware Description Unicom's Power over Ethernet Splitter Adapter has three connection ports, one LED indicator, and a voltage adjustment DIPswitch. Data In port: This is an RJ-45 Ethernet interface port for data transmission into the PoE Splitter. This port connects with a PoE injector. The Data In port Data Out port: This is an RJ-45 Ethernet port and has a detachable RJ-45 cable for connecting with a PoE device such as a camera. Power Out port: The adapter supports and includes two typ
ページ6に含まれる内容の要旨
System Power LED indicator DIPswitch: The DIPswitch changes the splitter voltage allowing for it to operate with a variety of products. It provides four voltage values – 5V, 7.5V, 9V and 12V. The default is 5V. Before adjusting the DIPswitch, disconnect the power from Splitter Adapter. DIPswitch
ページ7に含まれる内容の要旨
Installation To install the Power over Ethernet Splitter, please follow the steps below. 1. Use an RJ-45 cable to connect the Data In port on the Power over Ethernet Splitter Adapter with the Data Out port of a PoE Hub. If the hub does not support PoE function, you'll need to install a PoE Injector (pn: POE-32001T) between the hub and splitter. 2. Use an RJ-45 cable to connect the Data Out port on the PoE Splitter Adapter to a remote device (Such as a router, access point, camera, etc.). 3. Choo
ページ8に含まれる内容の要旨
Technical Specification IEEE802.3 10BASE-T Standard IEEE802.3u 100BASE-TX IEEE802.3af Power over Ethernet (2) Power Cables, Power jack each with straight and a right angle plugs diameter Plug dimension: 5.5 x 2.0mm, 5.5 x 2.5mm DIPswitch Four-segment output voltage switch Data / Power In: 1 x RJ-45.Data pin 1,2,3,6 Power pin: 4,5(V+), 7,8(V-) and 1,2(V+), 3,6(V-) Connector Data Out: 1 x RJ-45, Data pin 1,2,3,6 Power out jack: 5V, 7.5V, 9V, 12V (Adjustable) Maximum feeding current: 2.0A@5V 10Base
ページ9に含まれる内容の要旨
908 Canada Court City of Industry, CA 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880 www.unicomlink.com e-mail: info@unicomlink.com UNIDOC020905
