ページ1に含まれる内容の要旨
ENNHD-1GS
3.5” SATA HDD Network Storage Enclosure
User’s Guide
ページ2に含まれる内容の要旨
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com
ページ3に含まれる内容の要旨
TABLE OF CONTENTS OVERVIEW ....................... 5 UNPACKING INFORMATION ............................................. 5 INTRODUCTION TO THE GIGABIT SATA NAS WITH USB .. 6 Key Features ...............................................................................6 Front Panel...................................................................................7 Power Button................................................................... 7 LEDs Definition................................
ページ4に含まれる内容の要旨
STARTING THE GRAPHIC USER INTERFACE (GUI) ........... 23 USING THE GRAPHIC USER INTERFACE (GUI) ................ 24 Understanding the GUI.......................................................................24 Management items list .......................................................................24 STATUS..................................................................... 26 Items ..............................................................................................26 Infor
ページ5に含まれる内容の要旨
MAINTENANCE ........................................................... 47 Upload/ Download Your Configuration..............................47 Backup the Device Configuration Status:.......................... 47 Reload the Device Configuration Status: .......................... 48 Code Page ..................................................................................48 Firmware Upgrade...................................................................48 Restart the System ............
ページ6に含まれる内容の要旨
Overview Thank you for purchasing the product. Read this chapter to know about your Gigabit SATA NAS with USB. Unpacking information Before getting started, please verify that your package includes the following items: 1. One Gigabit SATA NAS with USB 2. One Power adapter and one AC power (Hard Disk not Included) cable. 3. One Quick Installation Guide 4. One Utility/ Manual CD 5. HD Fastening screw x 4 5
ページ7に含まれる内容の要旨
Introduction to the GIGABIT SATA NAS with USB Easily back-up your data and share them, this Gigabit SATA NAS with USB is a high-speed, economical, powerful NAS (Network Attached Storage), using the efficient SATA interface and providing an excellent data storage and sharing solution for your small business, SOHO (Small Office or Home Office) or personal requirement. You may also back-up those files from your USB storage devices with pressing the “Backup” button. Embedding FTP server
ページ8に含まれる内容の要旨
Front Panel Power Button To activate the device, press this Power button for 2 seconds after connecting the device to an appropriate power outlet with the provided power cord. To power off, press the button for two seconds until Power LED starts to blink. LEDs Definition LED Status Power Steady Blue Power on Blinking Blue System starting\ closing Off Power off LAN Steady Green Valid Connection at 1000 Mbps Blinking Green Data transmitting at 1000 Mbps
ページ9に含まれる内容の要旨
Backup Button Press this button to copy those files from USB I port to the internal HD. A new folder will be created automatically in the “share” folder. This new folder is named according to the time you press this button. Note: 1. Only USB I port support this quick backup function. 2. The Backup LED illuminates while data copying. Do not remove this device from USB I port before the Backup LED turns off. eSATA connector Connect this port with your eSATA device. 8
ページ10に含まれる内容の要旨
Rear Panel Reset to Default Button Press and hold the Reset Default Button for 4 seconds to reset all configurations to factory default settings. Note: 1. All configurations that are done by users will be removed from the device. 2. The device also supports restoring factory default settings by software. To get instruction restoring factory default parameters, see” Reset to Factory Default” LAN Port Connect the port with RJ-45 cable to y
ページ11に含まれる内容の要旨
Installation Guide Hardware Installation Install a Hard Disk Drive for the Device 1. Lie the device down as the following picture. Please make sure that the device is oriented correctly. 2. Unscrew the screws on both the top and bottom side of the device. 3. Remove the HD cover from the device evenly. 10
ページ12に含まれる内容の要旨
4. Place the Hard Disk drive evenly on the hard disk drive base. Slides the Hard Drive to connect to the connector on the device. 5. Secure your hard disk with the included screws in the package. 6. Place the HD cover back on to the device and screw the cover on. Connect this device to your Local Area Network (LAN) 1. Connect one end of a RJ-45 cable to the LAN port on the device. 2. Connect the other end of the cable to your IP sharing router or switch 11
ページ13に含まれる内容の要旨
Connect this device to your USB devices The device equips two USB ports that allow users to connect the device to a USB storage device . 1. Find the USB cable that came with your USB storage device. Insert the USB Type A end of the cable to the device, the other end to your USB storage. Note: a. The Type A end of the USB cable is usually the end that connects to your computer. b. If you are connecting an external HD to the USB ports on the device, we recommend users to connect t
ページ14に含まれる内容の要旨
Power on the device 1. Connect the included power cord with the power adapter 2. Connect the connector end to the device and the plug to an outlet. 3. Push the power button to power on. 13
ページ15に含まれる内容の要旨
Software Installation Installing the PNMD This PNMD program helps users to get accessed to those NAS in your LAN. Please follow the instructions to install the software. 1. Insert the CD-Rom that came with this product to your CD-Rom drive. The main menu pops up automatically. Click the “Install PNMD” button to start installation. Note: If the auto-run program is not activated, please click on “My Computer” your CD-Rom Drive then click the InstallMenu icon to start the main m
ページ16に含まれる内容の要旨
3. Fill your User Name and Company name in their respective blanks. Select if you want this software to be used by anyone who uses this computer or yourself only. Click Next to proceed. 4. Choose the destination folder for this software and click “Next” to start installation. You may click Browse to change the location. 5. Click “Finish” to complete the software installation. 15
ページ17に含まれる内容の要旨
6. After successful installation, the shortcut shows on your windows desktop. Note: For instructions using the software, please refer to chapter “Making Connection with the Device”. Installing the EZIP Backup This EZIP Backup helps users to backup files on your computer to NAS. Please follow the instructions below to install the software. 1. Insert the CD-Rom that came with this product to your CD-Rom drive. The main menu pops up automatically. Click the “Install EZIP Backup”
ページ18に含まれる内容の要旨
3. Fill your User Name and Company name in their respective blanks. Select if you want this software to be used by anyone who uses this computer or yourself only. Click Next to proceed. 4. Choose the destination folder for this software and click “Next” to start installation. You may click Browse to change the location. 5. Click “Finish” to complete the software installation. 17
ページ19に含まれる内容の要旨
6. After successful installation, the shortcut shows on your windows desktop. Note: For instructions using the software, please refer to chapter “ Using EZIP Backup to backup your files” in Appendix. Making Connection with the Device Connecting the device with PNMD 1. Double click the shortcut on your desktop. The PNMD begins scanning NAS in your LAN. Please click “Next” to proceed after the Welcome window pops up. Note: This window pops up only when there is no device det
ページ20に含まれる内容の要旨
3. Connect the LAN port to your switch or IP sharing router. The PNMD scanning the device again. 4. After scanning, the menu shows the NAS in your LAN. You may click the button to search for NAS in your LAN again. 19
