ページ1に含まれる内容の要旨
Users Manual
®
ioSafe SoloPRO External Hard Drive – eSATA/USB 2.0
eSATA/USB 2.0
Fireproof
Waterproof
Data Recovery Service
FloSafe Cooling Technology
3 Year Limited Warranty
910-10920-00 REV 02
ページ2に含まれる内容の要旨
Contents Welcome ............................................................................................................ 3 Precautions ........................................................................................................ 7 Package Contents ............................................................................................... 8 Specifications ..................................................................................................... 9 System Require
ページ3に含まれる内容の要旨
Welcome ® Thank you for purchasing the ioSafe SoloPRO external hard drive - the first high capacity external hard drive available with protection from fires and floods. For years, ioSafe has continued to set the standard for disaster proof hardware. The ioSafe SoloPRO brings our technology forward with an unprecedented combination of security, reliability, capacity and price. The ioSafe SoloPRO has been rigorously tested to protect the data contained in the device to meet the following sp
ページ4に含まれる内容の要旨
Copyrights Copyright ioSafe, Inc. 2010. All rights reserved. No part of this publication may be reproduced or transmitted in any form by any means, electronic, mechanical photocopying, recording or otherwise, without prior written consent. Trademarks All Trademarks mentioned or appearing in this document are the property of their respective owners. Federal Communication Commission (FCC) Radio Frequency Interference Statement This product complies with Part 15 of the FCC Rules. Operati
ページ5に含まれる内容の要旨
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that in
ページ6に含まれる内容の要旨
CE Compliance For Europe Marking by the CE symbol indicates compliance of this system to the applicable Council Directives of the European Union, including the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC). A “Declaration of Conformity” in accordance with the applicable directives has been made and is on file at ioSafe, Inc. Changes The material in this document is for information only and subject to change without notice. While reasonable efforts have been made
ページ7に含まれる内容の要旨
Precautions Please read the precautions listed below. Failure to do so may result in damage to the device, loss of data, and voiding of the warranty If you are using the SoloPRO for primary storage (as opposed to data backup) we strongly recommend that you backup your data. If the SoloPRO has a three-prong plug, do not plug the unit into a two- prong outlet. Do not bump, jar or drop the SoloPRO. Do not disconnect any cables while the SoloPRO is powered on without first stopping th
ページ8に含まれる内容の要旨
Package Contents Included in the package: A. ioSafe SoloPRO external hard drive B. AC power Module C. US Power Cord D. USB 2.0 Cable E. eSATA Cable F. Users guide (This booklet) G. Attention notice (Not shown) 8
ページ9に含まれる内容の要旨
Specifications Dimensions (Inches) .......................................................... 5.0W X 7.1H X 11.0L Weight (Lb) ................................................................................................... 15 Interface Transfer Rate USB 2.0 .................................................................... up to 480 Mbps eSATA ........................................................................ up to 3.0 Gbps External Power Supply AC Input ..............
ページ10に含まれる内容の要旨
System Requirements For Windows: The SoloPRO drive is formatted with an NTFS file system, a default for the Windows OS. For Mac: The Solo is supported on Mac’s using the G3 (or later) or Intel processor. When connecting to a Mac, the SoloPRO drive will need to be reformatted once connected. (See page 21 - Formatting the SoloPRO for Mac OS) Supported OS/interface connection: Linux .............................................................................................. eSATA O
ページ11に含まれる内容の要旨
About USB 2.0 USB 2.0 has a maximum interface transfer rate, or bandwidth, of 480 Mbps (Megabits per second). The performance depends on many factors including: CPU, file system overhead, number of attached USB devices and more. Given these and other factors, in day-to-day use you can expect maximum, sustained transfer rates around 25 MB/s (Megabytes per second). USB 2.0 is backwards compatible with USB 1.1. This means you can connect a USB 2.0 device to USB 1.1 port, and vice versa.
ページ12に含まれる内容の要旨
About eSATA eSATA, or external SATA, is a high performance interface that provides up to 6x faster transfer rates than USB 2.0 (up to 3 Gbits/sec). It was developed to extend the internal SATA interface to external devices. eSATA supports hot- swapping by design, however, this feature requires proper support and setup at the host, device (drive), and operating-system level. Connecting the SoloPRO through eSata is recommended for best drive performance and OS compatibility. NOTE: The cab
ページ13に含まれる内容の要旨
Securing the SoloPRO (Suggestions) Kensington® Security Slot For drive security, the SoloPRO is equipped with a Kensington security slot, which supports a standard Kensington security cable (sold separately). For more information on the Kensington security slot and available products, visit www.kensington.com. Kensington® Security Slot 13
ページ14に含まれる内容の要旨
For Added Security For added security, the SoloPRO can be secured with a cable and padlock or bolted to a floor. See the pictures below for suggested methods on physically securing the SoloPRO. 14
ページ15に含まれる内容の要旨
Connecting the SoloPRO to Your Computer Using the USB connection 1. Connect the included power supply to the back of the SoloPRO. CAUTION! To avoid damage to the power supply connector, make sure it is aligned correctly before plugging it into the drive. Do not move the drive while it is powered up to avoid drive damage or data loss. a) Plug in the AC cord in the power supply. b) Plug the small end of the power supply into the Solo’s power port. c) Plug the AC cord into an AC outlet.
ページ16に含まれる内容の要旨
4. Verify that the Drive Mounts. Before storing data on the SoloPRO, the drive must be “mounted” to the computers operating system. This means that the computers operating system has recognized at least one readable partition on the drive and established a communication link with it. For Windows PC, once the SoloPRO is powered on the operating system should mount the drive in a few moments. A new drive icon/letter will appear in My Computer/Windows Explorer. You are now ready to use th
ページ17に含まれる内容の要旨
eSATA Connection For best performance and compatibility with Windows Server and Linux, connect the drive to an eSATA host adapter or a built-in external eSATA connection. Connect the drive to USB if a supported eSATA connection is not available. 1. Verify eSATA drivers are properly installed. NOTE: You do not need to install special drivers for the SoloPRO hard drive. It is supported by the drivers included with the eSATA host adapter or built-in eSATA connection. 2. Shut down the
ページ18に含まれる内容の要旨
3. Connect the included power supply to the SoloPRO. CAUTION! To avoid damage to the power supply connector, make sure it is aligned correctly before plugging it into the drive. Do not move the drive while it is powered up to avoid drive damage or data loss. a) Plug in the AC cord to the power supply. b) Plug the small end of the power supply into the SoloPRO’s power port. c) Plug the AC cord into an AC outlet. 4. Connect the eSATA cable from the PC to the SoloPRO. NOTE: Never conn
ページ19に含まれる内容の要旨
6. Verify that the Drive Mounts. Before storing data on the SoloPRO, the drive must be “mounted” to the computers operating system. This means that the computers operating system has recognized at least one readable partition on the drive and established a communication link with it. For Windows, once the OS boots, a new drive icon/letter will appear in My Computer/Windows Explorer. You are now ready to use the SoloPRO. For Mac, once the OS boots, a new drive icon will appear on the Des
ページ20に含まれる内容の要旨
Disconnecting and Reconnecting the Drive using eSATA eSATA supports hot-swapping by design, however, this feature requires proper support and setup at the host, device (drive), and operating-system level. If not properly configured you may have to power off your computer and the SoloPRO before disconnecting. CAUTION! To avoid data loss, make sure you shut down your computer before turning off power to the drive. Do not move or disconnect the drive while it is powered up. The system sh
