ページ1に含まれる内容の要旨
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
XM-6802B
CD-ROM DRIVE
USER MANUAL
ページ2に含まれる内容の要旨
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the CD-ROM Drive.........................................................6 Troubleshooting.......................................................................9 Specifications ........................................................................10 Drive Connectors...................
ページ3に含まれる内容の要旨
INTRODUCTION – XM-6802B CD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (eject button, software, emergency eject hole) DAE (Digital Audio Extraction) Audio Capability MPC3 and Photo-CD Multi-session Compatibility Headphone Output Volume Control Supports CD-RW Play: Drive Speed 52X BUS Interface ATAPI Types of Disc Formats Supported CD • CD-DA (Red Book) – Standard Audio CD & CD-Text • CD-ROM (Yellow Book Mode 1 & 2) – Standard Data • CD-ROM-XA (Mo
ページ4に含まれる内容の要旨
Insert CD Disc in tray ① CD Tray When you install a disc into the CD-ROM drive, the BUSY light flashes ➁ Busy Indicator slowly as it attempts to locate the disc. One of the following will occur: • BUSY light goes out. The CD-ROM drive is ready to read data from the disc. • BUSY light flashes slowly. The disc may be dirty. • BUSY light remains ON. The CD-ROM is accessing data. • BUSY light remains ON indefinitely. The CD-ROM is experiencing an error The EJECT button is used to o
ページ5に含まれる内容の要旨
SETUP – XM-6802B CD-ROM The following steps must be performed to properly install your drive: • Set CD-ROM Drive Jumper Settings • Connect Audio Cable (optional) • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the CD-ROM drive. By placing a jumper on the pins, you can select the following functions: CS Drive is configured using host interface signal CSEL SL Configures dr
ページ6に含まれる内容の要旨
Placing CD-ROM Drive inside your Computer Now that you have set the jumpers, you are ready to install your CD-ROM drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. Your Toshiba CD-ROM drive can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vert
ページ7に含まれる内容の要旨
Power Cable - Connect an internal computer power supply cable to the power socket at the back of the CD- ROM drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly. Figure 4.Installing Power Cable Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD audio cable. Toshiba's CD-ROM
ページ8に含まれる内容の要旨
USING THE CD-ROM Drive – XM-6802B Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close. Inserting a Disc - Vertically To insert a disc in a drive that is mounted vertically,
ページ9に含まれる内容の要旨
Removing a Disc To remove a disc from the CD-ROM drive, perform the following steps: 1. Open the Loading Tray by pressing the Eject Button. 2. Grasp disc by edges, and lift out of loading tray. 3. Press Eject Button again to close Loading Tray. Usage Guidelines • Keep the disc tray closed when not using the CD-ROM Drive. • Do not press down on the disc tray when opening or closing it. • Do not place objects on the disc tray. • Never use a damaged, broken, or deformed disc. • Do
ページ10に含まれる内容の要旨
Cleaning Media Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed. If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather from the inner side outward. 8
ページ11に含まれる内容の要旨
TROUBLESHOOTING – XM-6802B Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables). • Are the drive configuration jumpers on the CD-ROM drive set properly? • Is the software driver loaded? On a step-by-step (F8) Boot of the system is the CD-ROM dri
ページ12に含まれる内容の要旨
SPECIFICATIONS –XM-6802B General Interface ATAPI Compatible CD-ROM Standards CD-DA (Red-Book) - Standard Audio CD & CD-Text CD-ROM (Yellow-Book Mode 1 & 2) - Standard Data CD-ROM XA (Mode2 Form 1&2) - Photo CD, Multi-Session CD-I/FMV (Green Book, Mode 2 Form1&2, Ready, Bridge) CD-Extra/CD-Plus (Blue Book) - Audio & Text/Video Video-CD (White Book) - MPEG1 Video Performance Data Transfer Rate CD-ROM/R Read (mode 1): 7,800 Kbytes/s CD-RW Read Mode 1) 6,000 Kbytes/s Transfer
ページ13に含まれる内容の要旨
Power DC Voltage and Current Requirements 5V 5%, 12V 10% Physical Height 5.83" (148.2mm) Width 1.65" (42mm) Depth 7.24" (184mm) Weight 1.66lbs (740g) Connectors DC input AMP 1-480424-0 or equivalent, 2m max ATAPI Interface Connector 40 Pin ATAPI Standard, 0.46m max length Analog Audio Line Output Connector 4 Pin ATAPI Standard, 3m max) Regulatory The XM-6802B CD-ROM drive has been certified by the following regulatory agencies: UL 1950 E225119 CAN/CSA C22.2 No. 950
ページ14に含まれる内容の要旨
DRIVE CONNECTORS –XM-6802B Figure 1.XM-6802B CD-ROM Drive Rear Panel - Connectors Power Power is supplied to your CD-ROM drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug Connector has chamfered edges, so the power connector fits only one way CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON. Audio Supplies Analog sound to your system
ページ15に含まれる内容の要旨
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN I/O SIGNAL HOST SIGNAL NAME PIN I/O SIGNAL HOST SIGNAL NAME NO. NAME NO. NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 - GND 3 I/O HD7 Host Data Bus BIT 7 23 I HWR-,STOP Host I/O Write 4 I/O HD8 Host Data Bus BIT 8 24 - GND 5 I/O HD6 Host Data Bus BIT 6 25 I HRD-, Host I/O Read HDMARDY, - HSTROBE 6 I/O HD9 Host Data Bus BIT 9 26 - GND 7 I/O HD5 Host Data Bus BIT 5 27 O IORDY, I/O Channel Ready
