ページ1に含まれる内容の要旨
VP-6228(T)
USB 2.0, 5.25-inch External Enclosure
User’s Manual
ページ2に含まれる内容の要旨
PROPRIETARY NOTICE We makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this document may be p
ページ3に含まれる内容の要旨
Contents 1. Introduction ................................................................................. 4 1-1 Features and Specifications ........................................................... 4 1-2 USB 2.0 External Drive ................................................................ 5 1-3 Package Checklist ......................................................................... 5 2. Hardware Installation ................................................................. 6 2-1 An
ページ4に含まれる内容の要旨
1. Introduction Congratulation on your purchase of VP-6228(T) USB2.0, 5.25” External Enclosure. This External Enclosure has been designed to provide hot-swapping and Plug-n-Play operations of internal 5.25” IDE devices and 3.5” MobileRocks. Supplied with this external en- closure is a USB 2.0 cable, power vertival-holder adapter, stand for enclosure and a CD containing installation driver(s). The USB 2.0 cable enables connection of the external enclosure to your PC, Notebook or MAC. 1-1 Featur
ページ5に含まれる内容の要旨
5. Supports ATA PIO modes 0-4: ATA interface operation mode is automatically selected during device initialization or manually programmed with configuration data 6. Supports UDMA modes 0-4 7. Supports 48-bit LBA (large HDD), when the VP-6228(T) con- nects with one 3.5” HDD installed in the MobileRACK 1-2 USB 2.0 External Drive The USB 2.0 External Drive is a portable compact storage drive that incorporates the USB 2.0 (Universal Serial Bus 2.0) high speed interface. The USB 2.0 External Drive p
ページ6に含まれる内容の要旨
2. Hardware Installation 2-1 Analog Audio Connector(JP1) Bulid-in connector (JP1) has two channels,right(“R”) and left (“L”) audio outputs, and allows you to direct audio output from your CD/ DVD-ROM Drive to your sound device. JP1 L GNDGND R 2-2 Jumper Settings 2-2.1 Jumper Settings for assembling with MobileRack Jumper JP6, located on the rear PCB panel of the VP-6228(T), is used to set running the VP-6228(T) external enclosure. The producer setting is JP6 pins 1-2 ON. 3 JP6 1-2 :ON -->VP-6
ページ7に含まれる内容の要旨
2-2.2 Temperature Control Jumper Settings (Only VP-6228T) Jumpers JP7 and JP8, located on the rear PCB panel of the VP-6228T, are used to set the cooling fan for controlling the operating temperature. The default setting is JP8 pins 1-2 ON. The fan will always run continuously to disperse the heat. Note: Only one jumper can be set at the same time. The following identifies the jumper options for setting the operation of the cooling fan. JP8 (2-pin) Jumper Temperature JP7 JP8 When JP8 pins 1-2 ar
ページ8に含まれる内容の要旨
2-3 Assemble the USB 2.0, 5.25” External Enclosure VP-6228(T) With One 5.25” IDE Device or One Mobile Rack Step1. Remove the four rubber stands on the VP-6228(T) external enclosure by gently prying them off. Step2. Remove the four cover retaining screws securing the top enclo- sure cover. (The four cover retaining screws are located in the mounting holes on the Top enclosure cover.) 8 VP-6228(T) USER MANUAL
ページ9に含まれる内容の要旨
Step3. Separate the top and bottom enclosure covers. Step4. a) Place the 5.25” IDE Device or the Mobile Rack in the bottom enclosure cover. (Place one 5.25” IDE Device in the bottom enclosure cover) OR (Place one 5.25” IDE Device in the bottom enclosure cover) (--->Next Page) VP-6228(T) USER MANUAL 9
ページ10に含まれる内容の要旨
(Place one 5.25” IDE Device in the bottom enclosure cover) b) Attach the IDE 40-pin data cable from the rear panel of the bottom cover to the 40-pin connector on the back of the 5.25 “ device or Mobile Rack. To ensure pin-1 to pin-1 connection, orient the cable so the colored stripe edge is closest to the power connector. c) Attach the 4-pin power cable from the rear panel of the bottom cover to the 4-pin connector on the back of the 5.25” device or Mobile Rack. The connector is “D” shaped to en
ページ11に含まれる内容の要旨
Step5. a) Make sure the the 5.25” IDE device’s front face panel or the MobileRack’s front face panel should be flush with the front corners (positioned in front of the guide flanges) of the bottom enclosure cover. b) Align the 5.25” IDE device or the Mobile Rack mounting holes with the mounting holes on the bottom cover and secure with four drive retaining screws (two on each side). OR VP-6228(T) USER MANUAL 11
ページ12に含まれる内容の要旨
Step6. Place the top enclosure cover over the drive assembly. OR 12 VP-6228(T) USER MANUAL
ページ13に含まれる内容の要旨
Step7. Align the 5.25” IDE device or the Mobile Rack mounting holes with the mounting holes on the bottom cover and secure with four cover retaining screws (two on each side). OR VP-6228(T) USER MANUAL 13
ページ14に含まれる内容の要旨
Step8. (Assemble the VP-6228(T) with one 5.25” IED Device) Replace the four rubber stands, one on each of the four corners. Orient each stand so the raised nub is on the bottom. 14 VP-6228(T) USER MANUAL
ページ15に含まれる内容の要旨
( OR Assemble the VP-6228(T) with one MobileRACK) Replace the four rubber stands, one on each of the four corners. Orient each stand so the raised nub is on the bottom. VP-6228(T) USER MANUAL 15
ページ16に含まれる内容の要旨
Step9. A vertical-holder stand is also provided as a convenient, space- saving method for setup of the VP-6228(T) external enclosure on your desktop. Simply align the grooves of the VP-6228(T) external enclosure with the guides on the stand and slide together. VP-6228(T) External Enclosure with Vertical-Holder Stand (Assembled with one 5.25” IDE Device) OR VP-6228(T) External Enclosure with Vertical-Holder Stand (Assembled with one Mobile Rack) The installation is complete and the VP-6228(T) Ext
ページ17に含まれる内容の要旨
2-4 Connect the USB 2.0, 5.25” External Enclosure VP-6228(T) to Your Computer Computer system requirements Hardware Notebook or desktop computer with support for USB or USB 2.0. Operating System Windows 98SE/Me/2000/XP, and Mac OS 9.0 or above. Proceed the following steps to connect to Your Computer Step1: Boot-up your computer. Make sure the USB/USB 2.0 host adapter and driver are installed in your computer. Step2: Connect one USB connector end of the USB cable into the USB Port of your USB 2.
ページ18に含まれる内容の要旨
3. Drivers Installation 3-1 Windows 98SE If this is the first time using your USB 2.0 External Drive, you must first run the [SETUP.EXE] from the USB 2.0 “Drivers and Utility Installation” CD after you connect your USB 2.0 External Drive to your computer. Then proceed with the following: 1. Connect your USB 2.0 external drive to an available USB port on your computer. 2. An “Add New Hardware Wizard” screen will appear. Click [Next]. 3. Select “Display a list of all drivers” then click [Next].
ページ19に含まれる内容の要旨
4. Click [Browse]. 5. Double click on the ViPowER CD icon of the [My Computer] directory. 6. Select “Win98” under the “Drivers” directory, then click [OK]. VP-6228(T) USER MANUAL 19
ページ20に含まれる内容の要旨
7. Click [Next]. 8. Click [Next]. 9. The system will request you to restart your computer. Click [FINISH]. 20 VP-6228(T) USER MANUAL
