ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade- marks of NVIDIA C
ページ3に含まれる内容の要旨
Safety Instructions 1. Always read the safety instructions carefully. 2. Keep this User’s Manual for future reference. 3. Keep this equipment away from humidity. 4. Lay this equipment on a reliable flat surface before setting it up. 5. The openings on the enclosure are for air convection hence protects the equip- ment from overheating. DO NOT COVER THE OPENINGS. 6. Make sure the voltage of the power source and adjust properly 110/220V be- fore connecting the equipment to the power inlet. 7. Pla
ページ4に含まれる内容の要旨
FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communications. Howev
ページ5に含まれる内容の要旨
WEEE (Waste Electrical and Electronic Equipment) Statement v 7563v1.1-0 Preface.p65 5 2008 /11/11, 下午 05:36
ページ6に含まれる内容の要旨
vi 7563v1.1-0 Preface.p65 6 2008 /11/11, 下午 05:36
ページ7に含まれる内容の要旨
vii 7563v1.1-0 Preface.p65 7 2008/11/11, 下午 05:36
ページ8に含まれる内容の要旨
CONTENTS Copyright Notice ..............................................................................................................ii Trademarks .......................................................................................................................ii Revision History ..............................................................................................................ii Technical Support .............................................................................
ページ9に含まれる内容の要旨
DOT (Dynamic OverClocking) ............................................................................. B-5 Clock ..................................................................................................................... B-6 Voltage ................................................................................................................. B-7 FAN Speed ........................................................................................................... B-8 Temperature ...
ページ10に含まれる内容の要旨
Getting Started Chapter 1 Getting Started Thank you for choosing the G41M Series (MS-7563 v1.X) Micro-ATX mainboard. The G41M Series mainboards are ® based on Intel G41M & ICH7 chipsets for optimal system ® efficiency. Designed to fit the advanced Intel Core 2 Duo/ Quad/Pentium/Celeron LGA775 processor, the G41M Se- ries deliver a high performance and professional desktop platform solution. 1-1 7563v1.0-1.p65 1 2008 /11/11, 下午 05:36
ページ11に含まれる内容の要旨
MS-7563 Mainboard Mainboard Specifications Processor Support ® - Intel Core 2 Quad/ Core 2 Duo/ / Yorkfield/ Wolfdale processors in LGA775 package - Supports 4 pin CPU Fan Pin-Header with Fan Speed Control (For the latest information about CPU, please visit http://global.msi.com.tw/index.php?func=cpuform2) Supported FSB - 1333/ 1066/ 800 MHz Chipset ® - North Bridge: Intel G41 chipset ® - South Bridge: Intel ICH7 chipset Memory Support - DDR2 667/800 SDRAM (8GB Max) - 2 DDR2 DIMMs (240pin / 1.8V
ページ12に含まれる内容の要旨
Getting Started - 1 DisplayPort jack - 4 USB 2.0 Ports - 1 RJ-45 LAN jack - 1 1394 port (optional) - 6 flexible audio jacks On-Board Pinheaders/ Connectors - 2 USB 2.0 pinheaders - 1 CD-in pinheader - 1 SPDIF-Out pinheader - 1 IEEE 1394 pinheader (optional) - 1 Front Panel Audio pinheader - 1 Serial port pinheader - 1 TPM (optional) - 1 Chassis Intrusion Switch pinheader - 1 Parallel Port pinheader Slots - 1 PCI Express x16 slot - 1 PCI Express x 1 slot - 2 PCI slots - Support 3.3V/ 5V PCI bus
ページ13に含まれる内容の要旨
MS-7563 Mainboard Mainboard Layout JCI1 Top : Mouse Bottom:Keyboard Fintek F71882FG Top: VGA port Bottom:DVI-D port DisplayPort Jack T: 1394 port(optional) JPW1 B: USB ports Top: LAN Jack Intel Bottom: USB ports G41 T:Line-In Realtek M:Line-Out B:Mic SYSFAN1 T:RS-Out M:CS-Out B:SS-Out PCI _E1 PCI _E2 RTM875T-605 BATT PCI 1 + Intel ICH7 ALC888 PCI 2 SATA2 SATA4 JUAD1 CD_IN1 JSPD1 JUSB1 JUSB2 J1394_1(optional) JBAT1 SATA1 SATA3 G41M Series (MS-7563 v1.X) Micro-ATX Mainboard 1-4 7563v1
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
Hardware Setup Chapter 2 Hardware Setup This chapter provides you with the information about hardware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly. Use a grounded wrist strap before handling computer components. Static electricity may damage the components. 2-1 7563v1.0CH2 Hardware Setup.p65 1 2008/11/11, 下午 05:36
ページ16に含まれる内容の要旨
MS-7563 Mainboard Quick Components Guide JCI1, ATX1, p.2-14 p.2-9 SYSFAN1,JPW1, CPU, CPUFAN1, DDR2, p.2-14 p.2-9 p.2-3 p.2-14 p.2-7 FDD1, p.2-12 Back Panel, p.2-10 JLPT1, p.2-19 JTPM1, p.2-17 JCOM1, p.2-18 SYSFAN2, p.2-14 PCIE, p.2-21 IDE1, PCI, p.2-12 p.2-21 J1394_1, JUSB1/2, SATA1~4, p.2-15 p.2-18 p.2-13 JBAT1, JSPD1, p.2-20 p.2-15 JFP1/2, CD_IN1, p.2-16 p.2-16 JAUD1, p.2-17 2-2 7563v1.0CH2 Hardware Setup.p65 2 2008 /11/11, 下午 05:36
ページ17に含まれる内容の要旨
Hardware Setup CPU (Central Processing Unit) When you are installing the CPU, make sure to install the cooler to prevent overheating. If you do not have the CPU cooler, consult your dealer before turning on the computer. For the latest information about CPU, please visit http://global.msi.com.tw/index.php? func=cpuform2 Important Overheating Overheating will seriously damage the CPU and system. Always make sure the cooling fan can work properly to protect the CPU from overheating. Make sure that
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
Hardware Setup 5. Lift the load lever up and open the 6. After confirming the CPU direction load plate. for correct mating, put down the CPU in the socket housing frame. Be sure to grasp on the edge of the CPU base. Note that the align- ment keys are matched. alignment key 7. Visually inspect if the CPU is 8. Cover the load plate onto the seated well into the socket. If not, package. take out the CPU with pure vertical motion and reinstall. 2-5 7563v1.0CH2 Hardware Setup.p65 5 2008/11/11, 下午 05
ページ20に含まれる内容の要旨
MS-7563 Mainboard 9. Press down the load lever lightly 10. Align the holes on the mainboard onto the load plate, and then se- with the heatsink. Push down the cure the lever with the hook under cooler until its four clips get retention tab. wedged into the holes of the mainboard. 11. Press the four hooks down to fasten 12.Turn over the mainboard to con- the cooler. Then rotate the locking firm that the clip-ends are correctly switch (refer to the correct direction inserted. marked on it) to lock
